Hi Richard, It is Roles and it was a new Mountpoint that I tried.
On Tue, Feb 24, 2015 at 5:06 PM, Richards, Robert B. < [email protected]> wrote: > Is it "rolls" or "roles"? > > > -----Original Message----- > From: IBM Mainframe Discussion List [mailto:[email protected]] On > Behalf Of Jake anderson > Sent: Tuesday, February 24, 2015 3:34 AM > To: [email protected] > Subject: Re: [MVS-OE] Mount path more than 72 characters - error > > Hi lizette/All, > > The Syntax were in place : > > ----+----1----+----2----+----3----+----4----+----5----+----6----+----7-- > ***************************** Top of Data ****************************** > MOUNT FILESYSTEM('MFWSCC.MSPSINST.E1M40.QA.CE1MZFS') > MOUNTPOINT('/u/users/framewrk/mfwscc/mspsinst/chrr040/qa/roles/securit > y') TYPE(ZFS) MODE(RDWR) > > the above snapshot follows the correct syntax but during paste the > characters COLS value are changed. > > > > I tried mounting it via IKJEFT01 via Batch I received the below error > message > > READY > MOUNT FILESYSTEM('MMWSSS.ZSPPPPPP.EEM40.QA.AEZMZFS') > MISSING MOUNT POINT+ > MISSING PATH NAME OF THE MOUNT POINT IN QUOTES RETURN CODE 00000004 > RECEIVED DURING PARSING OF THE COMMAND. > READY > MOUNTPOINT('/u/users/ffffewkk/mmmsmc/mmmsinsz/zhrr040/qa/rolls/securi > INVALID COMMAND NAME SYNTAX > READY > y') TYPE(ZFS) MODE(RDWR) > INVALID COMMAND NAME SYNTAX > READY > END > > I am i missing anything on the above > > Regards, > Jake > > On Mon, Feb 23, 2015 at 7:50 PM, Lizette Koehler <[email protected]> > wrote: > > > Jake, > > > > When you are editing the BPXPRMxx member, turn on HILITE. Just type > > HILITE On the command line, then select the JCL option, place 3 in the > > right hand entry and then a / at the next entry > > > > It will help you see if you extended over column 71 > > > > Lizette > > > > > > > -----Original Message----- > > > From: MVS OpenEdition [mailto:[email protected]] On Behalf Of > > > Jake anderson > > > Sent: Monday, February 23, 2015 1:40 AM > > > To: [email protected] > > > Subject: [MVS-OE] Mount path more than 72 characters - error > > > > > > Hello, > > > > > > Cross Posted to IBM-MAIN and MVS-OE group. > > > > > > I am trying to mount the below paths using BPXPRM00(Used the '00' in > > > IEASYS00) but it fails. > > > > > > THE MOUNT POINT SPECIFIED IN BPXPRM00 DOES NOT EXIST. > > > BPXF008I FILE SYSTEM MMMMM.SSSSSS.EEEEE.QQ.ZFS 393 WAS NOT MOUNTED. > > > THE MOUNT POINT SPECIFIED IN BPXPRM00 DOES NOT EXIST. > > > BPXF008I FILE SYSTEM MMMMM.RRRRR.EEEEE.PP.ZFS 394 WAS NOT MOUNTED. > > > THE MOUNT POINT SPECIFIED IN BPXPRM00 DOES NOT EXIST. > > > > > > Mount point and File system: > > > > > > MOUNT FILESYSTEM('MMMMMM.SSSSSS.EEEEE.QQ.ZFS') > > > MOUNTPOINT('/u/users/fffworke/mfcharl/msinstal/chrr080/qq/rolll/secu > > > rit > > > y > > > ') TYPE(ZFS) MODE(RDWR) > > > > > > MOUNT FILESYSTEM('MMMMM.RRRRR.EEEEE.PP.ZFS') > > > MOUNTPOINT('/u/users/fffworke/mfcharl/msinstal/chrr080/qq/rolll/secu > > > rit > > > y > > > ') TYPE(ZFS) MODE(RDWR) > > > > > > As per the MVS tuning reference guide, the Mount definition can > > > given > > till > > > 71st line and the part of the definition can be continued in the > > > next > > line. > > > > > > I did the same based on Manual recommendation but during the MVS > > > SYNTAXCHECK it does not produces any error messages. After the IPL, > > > i get the above error messages. Then the same path I mount using > > > ISHELL.All the paths are in smaller case. > > > > > > Not sure if there is anything I missed. > > > > > > Any suggestions are advises much appreciated. > > > > > > z/OS : 2.1 > > > > > > Jake > > > > > > > ---------------------------------------------------------------------- > > For MVS-OE subscribe / signoff / archive access instructions, send > > email to [email protected] with the message: INFO MVS-OE > > > > ---------------------------------------------------------------------- > For IBM-MAIN subscribe / signoff / archive access instructions, send email > to [email protected] with the message: INFO IBM-MAIN > > ---------------------------------------------------------------------- > For IBM-MAIN subscribe / signoff / archive access instructions, > send email to [email protected] with the message: INFO IBM-MAIN > ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [email protected] with the message: INFO IBM-MAIN
