Or you could do a LISTC ENT(/) ALL and see if the other datasets were altered and not just this one.
Lizette > -----Original Message----- > From: IBM Mainframe Discussion List [mailto:[email protected]] > On Behalf Of Pommier, Rex > Sent: Tuesday, May 05, 2015 12:00 PM > To: [email protected] > Subject: Re: IDCAMS QUESTION > > Try renaming the non-SMS one to something outside your mask and trying it > again. If it works, you have your answer and your SMS datasets altered. > Then just rename the non-SMS one back. > > -----Original Message----- > From: IBM Mainframe Discussion List [mailto:[email protected]] > On Behalf Of esmie moo > Sent: Tuesday, May 05, 2015 12:55 PM > To: [email protected] > Subject: Re: IDCAMS QUESTION > > The dsns are all SMS managed except for SYS2.CA1 .TMSA.ACTQUE. This dsn > is on a non-SMS volume. Since IDCAMS encountered this dsn did it prevent > the ALTER of the other dsns? > The SYS2.CA1.TMSA dsns are from an older version of CA1. The current > versions are on non-SMS vols. > > -------------------------------------------- > On Tue, 5/5/15, Lizette Koehler <[email protected]> wrote: > > Subject: Re: IDCAMS QUESTION > To: [email protected] > Received: Tuesday, May 5, 2015, 1:06 PM > > Your dataset is not > managed by SMS - So you cannot alter the management class > > IDC3194I > SMS CONSTRUCT MANAGEMENTCLASS SPECIFIED FOR NON-SMS > MANAGED > > Did you place > your SYS2.CA1.TMSA on SMS managed volumes? Do you have the under > control of SMS? - This is something I would not do for CA1 TMC. > > > Lizette > > > > -----Original Message----- > > From: IBM Mainframe Discussion List > [mailto:[email protected]] > > On Behalf Of esmie moo > > Sent: Tuesday, May 05, 2015 9:01 AM > > To: [email protected] > > Subject: Re: IDCAMS QUESTION > > > > Just to confirm that > there is no space between the CA1 & .TMSA. The error > occurred when I > performed the copy/paste. > > > > > Sorry. > > > -------------------------------------------- > > On Tue, 5/5/15, esmie moo <[email protected]> > wrote: > > > > Subject: > IDCAMS QUESTION > > To: "IBM > MAIN" <[email protected]> > > Received: Tuesday, May 5, 2015, 11:31 AM > > Gentle Readers, > > I > am trying to alter the Management Class of the the following dsns using > > IDCAMS: > SYS2.CA1 .TMSA.**. I have done this in the past and it used to > work > however for some reason I am unable to do so. The message error > > posted for one dsn is self explanatory, however when I check all the dsns it > > shows that the alter did not work. Is it because it detected a problem > with > one dsn and doesn't process any of the dsns? If so, is there a work > around > it? Below is the output of the job : > > > > IDCAMS SYSTEM > SERVICES > > > > > > > > > > > > ALTER > SYS2.CA1 .TMSA.* - > > > > > > > > MGMTCLAS (NOMIG) > > > > > > > > IDC3194I SMS > CONSTRUCT MANAGEMENTCLASS SPECIFIED FOR NON-SMS > > MANAGED IDC3194I OBJECT > > > > IDC0532I **ENTRY > SYS2.CA1 .TMSA.ACTQUE NOT ALTERED > > > > > > IDC3003I FUNCTION > TERMINATED. CONDITION CODE IS 12 > > > > > > > > > > IDC0002I IDCAMS > PROCESSING COMPLETE. MAXIMUM CONDITION CODE > WAS 12 > > > ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [email protected] with the message: INFO IBM-MAIN
