I found information about check stop in the z/architecture POP CH11 PG 11-10
System Check Stop In a multiprocessing configuration, some errors, malfunctions, and damage conditions are of such severity that the condition causes all CPUs in the configuration to enter the check-stop state. This condition is called a system check stop. The state of the channel subsystem and I/O activity is unpredictable. I could not find a table that described reason code 0C. _________________________________________________________________ Dave Jousma Assistant Vice President, Mainframe Engineering [email protected] 1830 East Paris, Grand Rapids, MI 49546 MD RSCB2H p 616.653.8429 f 616.653.2717 -----Original Message----- From: IBM Mainframe Discussion List [mailto:[email protected]] On Behalf Of Jousma, David Sent: Friday, January 22, 2016 10:39 AM To: [email protected] Subject: Re: System check stopped state - what is it? I didn't look the code up, but I'm assuming you did a POR with an updated IOCDS? _________________________________________________________________ Dave Jousma Assistant Vice President, Mainframe Engineering [email protected] 1830 East Paris, Grand Rapids, MI 49546 MD RSCB2H p 616.653.8429 f 616.653.2717 -----Original Message----- From: IBM Mainframe Discussion List [mailto:[email protected]] On Behalf Of R.S. Sent: Friday, January 22, 2016 10:02 AM To: [email protected] Subject: Re: System check stopped state - what is it? Unfortunately no HW message: A logically partitioned mode event occurred. Select Details for information. Details: Logical partition LPAR01 is in the system check stopped state. Reason code = 0C. Note, it's not wait state, just "system check stopped state". I tried to use google, searched PoP and some other sources with no effect. I believe it is documented, but where??? Regards -- Radoslaw Skorupka Lodz, Poland W dniu 2016-01-22 o 15:51, Vernooij, CP (ITOPT1) - KLM pisze: > No messges id? > POP has some information about machine-checks and check-stop conditions, but > I couldn't find a 0C quickly. > > Kees. > > -----Original Message----- > From: IBM Mainframe Discussion List [mailto:[email protected]] On > Behalf Of R.S. > Sent: 22 January, 2016 15:35 > To: [email protected] > Subject: System check stopped state - what is it? > > I tried to perform LOAD on some LPAR. > I've got the following message: > > Logical partition LPAR01 is in the system check stopped state. Reason > code = 0C. > > Where to find the meaning of the code? > > > It is z13 machine. > -- Treść tej wiadomości może zawierać informacje prawnie chronione Banku przeznaczone wyłącznie do użytku służbowego adresata. Odbiorcą może być jedynie jej adresat z wyłączeniem dostępu osób trzecich. Jeżeli nie jesteś adresatem niniejszej wiadomości lub pracownikiem upoważnionym do jej przekazania adresatowi, informujemy, że jej rozpowszechnianie, kopiowanie, rozprowadzanie lub inne działanie o podobnym charakterze jest prawnie zabronione i może być karalne. Jeżeli otrzymałeś tę wiadomość omyłkowo, prosimy niezwłocznie zawiadomić nadawcę wysyłając odpowiedź oraz trwale usunąć tę wiadomość włączając w to wszelkie jej kopie wydrukowane lub zapisane na dysku. This e-mail may contain legally privileged information of the Bank and is intended solely for business use of the addressee. This e-mail may only be received by the addressee and may not be disclosed to any third parties. If you are not the intended addressee of this e-mail or the employee authorized to forward it to the addressee, be advised that any dissemination, copying, distribution or any other similar activity is legally prohibited and may be punishable. If you received this e-mail by mistake please advise the sender immediately by using the reply facility in your e-mail software and delete permanently this e-mail including any copies of it either printed or saved to hard drive. mBank S.A. z siedzibą w Warszawie, ul. Senatorska 18, 00-950 Warszawa, www.mBank.pl, e-mail: [email protected] Sąd Rejonowy dla m. st. Warszawy XII Wydział Gospodarczy Krajowego Rejestru Sądowego, nr rejestru przedsiębiorców KRS 0000025237, NIP: 526-021-50-88. Według stanu na dzień 01.01.2016 r. kapitał zakładowy mBanku S.A. (w całości wpłacony) wynosi 168.955.696 złotych. ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [email protected] with the message: INFO IBM-MAIN This e-mail transmission contains information that is confidential and may be privileged. It is intended only for the addressee(s) named above. If you receive this e-mail in error, please do not read, copy or disseminate it in any manner. If you are not the intended recipient, any disclosure, copying, distribution or use of the contents of this information is prohibited. Please reply to the message immediately by informing the sender that the message was misdirected. After replying, please erase it from your computer system. Your assistance in correcting this error is appreciated. ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [email protected] with the message: INFO IBM-MAIN This e-mail transmission contains information that is confidential and may be privileged. It is intended only for the addressee(s) named above. If you receive this e-mail in error, please do not read, copy or disseminate it in any manner. If you are not the intended recipient, any disclosure, copying, distribution or use of the contents of this information is prohibited. Please reply to the message immediately by informing the sender that the message was misdirected. After replying, please erase it from your computer system. Your assistance in correcting this error is appreciated. ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [email protected] with the message: INFO IBM-MAIN
