I have called it for many years from COBOL using the C string parameter
format (NULL terminated parameter string in the doc). No wrappers
needed. Here's a short snippet:
WORKING-STORAGE SECTION.
01 WORKAREA.
05 BPXWDYN PIC X(08) VALUE 'BPXWDYN'.
05 WS-BPXWDYN-RETCODE PIC 9(08) COMP SYNC.
05 WS-OUT1-ALLOC-STRING.
10 PIC X(15) VALUE
'ALLOC MSG(WTP) '.
10 PIC X(14) VALUE
'DD(OUT1) DSN('''.
10 WS-OUT1-DSN PIC X(45).
10 PIC X(01) VALUE SPACE.
10 PIC X(23) VALUE
'NEW DELETE UNIT(SYSDA) '.
10 PIC X(27) VALUE
'CYL SPACE(01,01) DSORG(PS) '.
10 PIC X(34) VALUE
'RECFM(FB) LRECL(80) BLKSIZE(27920)'.
*** TERMINATE COMMAND STRING
*** COULD SET THE LAST PARM AS A Z STRING
10 PIC X(01) VALUE LOW-VALUE.
PROCEDURE DIVISION.
STRING 'A.DYNAMIC.DSNAME'
''')' DELIMITED BY SPACE
INTO WS-OUT1-DSN.
CALL BPXWDYN USING WS-OUT1-ALLOC-STRING
RETURNING WS-BPXWDYN-RETCODE.
IF WS-BPXWDYN-RETCODE EQUAL ZERO
OPEN OUTPUT OUT-FILE
MOVE 'THIS IS SOME DATA !!!!' TO OUT-REC
WRITE OUT-REC
CLOSE OUT-FILE
ELSE
DISPLAY 'ERROR BPX RC=' WS-BPXWDYN-RETCODE
END-IF.
GOBACK.
Alan
Farley, Peter x23353 wrote:
I don't know in which language CA Easytrieve is coded, but a few years back I
tried setting up calls to BPXWDYN in Enterprise COBOL (V4.1 at the time) and
they did not work because COBOL does not zero R0 as BPXWDYN requires. I had to
code an assembler stub routine to put between the COBOL program and BPXWDYN to
get it to work. For simplicity the stub was non-reentrant to be able use the
LOAD macro to find a copy of BPXWDYN and save the entry point address for later
use.
Email me privately if you want a copy of the stub routine. It wasn't hard to
code, 40 actual code lines and 7 lines of comments.
Peter
-----Original Message-----
From: IBM Mainframe Discussion List [mailto:[email protected]] On Behalf
Of Hardee, Chuck
Sent: Tuesday, January 31, 2017 7:41 AM
To: [email protected]
Subject: Calling bpxwdyn from CA-Easytrieve
I have a need to be able to call bpxwdyn from within an CA-Easytrieve "program".
According to the manual, IBM says that bpxwdyn can be called from non-REXX
environments as long as certain rules are followed.
It also states that values can be returned as long as the return value
parameter follows the following format:
PARMx DC Y(L'PARMxVAL+1)
PARMxVAL DC C'parameter value '
(Notice the very important space at the end of the value string!)
The manual states that the length must be 1 greater than the maximum length
possible for the returned attribute. Since a dataset name can only be 44 bytes,
the length value should be fine.
My need it to call bpxwdyn and have it return to me the dataset name associated
with a specific DD name.
I have built the "command" string as follows:
bpxwdyn-command DC Y(L'bpxwdyn-info)
bpxwdyn-info DC C'INFO FI(MYDDN) '
I have built the information return parameter as follows:
bpxwdyn-dsname-p DC Y(102)
bpxwdyn-dsname DC CL100'INRTDSN '
The call in Easytrieve is CALL BPXWDYN USING (bpxwdyn-command, bpxwdyn-dsname-p)
What's happening is that I getting a return code of 20, invalid parameter.
What I don't get is whether it is with my command string or my returned value
strings.
The manual states that on a call from a non-REXX environment, R0 must be zero.
According to the Easytrieve manual, the CALL verb generates an MVS convention
calling list. So, based on that I can only assume that the last address in the
parameter list has it's high order bit on. Also, have written several routines
which trigger off of the number of parameters with the number of parameters
signaled by the high order but of the last one being on, and having called
these routines successfully in Easytrieve, I suspect my assumption is correct.
What I don't know is whether Easytrieve sets R0 to zero for the call. If it
doesn't, that could account for the return code of 20.
So, my question is, has anyone ever called bpxwdyn from within an Easytrieve
program?
Thanks,
Chuck
Charles (Chuck) Hardee<mailto:[email protected]>
Senior Systems Engineer/Database Administration
EAS Information Technology<mailto:DBA%20Engineering%20-%20DB2_IDMS>
Thermo Fisher Scientific
300 Industry Drive | Pittsburgh, PA 15275
Phone +1 (724) 517-2633 | Mobile +1 (412) 877-2809 | FAX: +1 (412) 490-9230
[email protected]<mailto:[email protected]> |
www.thermofisher.com
WORLDWIDE CONFIDENTIALITY NOTE: Dissemination, distribution or copying of this
e-mail or the information herein by anyone other than the intended recipient,
or an employee or agent of a system responsible for delivering the message to
the intended recipient, is prohibited. If you are not the intended recipient,
please inform the sender and delete all copies.
----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions,
send email to [email protected] with the message: INFO IBM-MAIN
