A DD Statement that uses INTRDR is a special DD.
INTRDR is used to submit REPORTS or JCL into SPOOL. So I am not sure exactly
what you are trying to do.
If you go to DA OSTC and PREFIX your STC name
Issue a ? next to the running task.
Next look in the list for JCLOUT
Is it there? And does it have any data in it?
Next go to O Panel in SDSF
Prefix your STC NAME.
See if there is anything on the spool for it. If there is, issue a ? next to
the Entry and see what DD statement it comes from
Here is what you should see when you do the ? next to the task name in the DA
OSTC panel
PREFIX=PRO* DEST=(ALL) OWNER=
NP DDNAME StepName ProcStep
JESMSGLG JES2
JESJCL JES2
JESYSMSG JES2
SYSPRINT PROJCLT
JESMSGLG JES2
JESYSMSG JES2
Here is what you could see if you do a ? next to an entry in the O panel display
PREFIX=* DEST=(ALL)
NP DDNAME StepName Output
REPORT IFOBAT I
Lizette
> -----Original Message-----
> From: IBM Mainframe Discussion List [mailto:[email protected]] On
> Behalf Of venkat kulkarni
> Sent: Sunday, May 07, 2017 4:16 AM
> To: [email protected]
> Subject: Re: job output into dataset
>
> Hello,
>
>
>
> Thanks for helping so far. I used below command
>
>
>
> $T JQ(IMS12RC3),SPIN,DDNAME=JCLOUT
>
>
>
> and output from this command is
>
>
>
> RESPONSE=TST4
>
> $HASP890 JOB(IMS12RC3)
>
> $HASP890 JOB(IMS12RC3) STATUS=(EXECUTING/TST4),CLASS=STC,
>
> $HASP890 PRIORITY=15,SYSAFF=(TST4),HOLD=(NONE)
>
>
>
>
>
>
>
> Job IMS12RC3 is,
>
>
>
> BROWSE SYS1.DEVL.PROCLIB(IMS12RC3) - 01.03 Line 0000000
>
> Command ===> Scr
>
> ********************************* Top of Data ********************
>
> // PROC RGN=0M,SOUT=A,
>
> // IMSID=IMS4,SYS2=
>
> //IEFPROC EXEC PGM=DFSMVRC0,REGION=&RGN,
>
> // PARM='DRC,&IMSID'
>
> //****************************************************
>
> //*
>
> //STEPLIB DD DSN=IMS4.V120.&SYS2.SDFSRESL,DISP=SHR
>
> //PROCLIB DD DSN=IMS4.V120.&SYS2.PROCLIB,DISP=SHR
>
> //JCLOUT DD SYSOUT=(A,INTRDR)
>
> //JCLPDS DD DSN=IMS4.V120.&SYS2.PROCLIB,DISP=SHR
>
> //SYSUDUMP DD SYSOUT=&SOUT
>
> //SYSABEND DD SYSOUT=&SOUT
>
> //*
>
> //************ DBRC RECON DD CARDS *******************
>
> //*
>
> //* USER SUPPLY THE DD CARDS
>
> //* REQUIRED FOR THE DBRC RECON DATA SET.
>
> //* IF NO DD STATEMENTS ARE SUPPLIED FOR RECON
>
> //* DATASETS, IMS ASSUMES THAT THE DATASETS
>
> //* HAVE BEEN DESCRIBED THROUGH THE DFSMDA MACRO.
>
> //*
>
> //RECON1 DD DSN=IMS4.V120.RECON1,DISP=SHR
>
> //RECON2 DD DSN=IMS4.V120.RECON2,DISP=SHR
>
> //RECON3 DD DSN=IMS4.V120.RECON3,DISP=SHR
>
> //*
>
>
>
> Can you please explain, what this command actually performed. As I mentioned,
> my plan was to cut messages from this job and put in one dataset using the
> command you suggested. Please correct , if I am missing anything.
>
>
----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions,
send email to [email protected] with the message: INFO IBM-MAIN
