While I hesitate to correct David, in this case a correction is warranted.
The proper command is:
CP TERMINAL CONMODE 3270
Perhaps David's suffering Monday Syndrome?
Respectfully,
Mike Walter
Hewitt Associates
Any opinions expressed herein are mine alone and do not necessarily
represent the opinions or policies of Hewitt Associates.
"David Boyes" <[EMAIL PROTECTED]>
Sent by: "The IBM z/VM Operating System" <[email protected]>
02/11/2008 12:25 PM
Please respond to
"The IBM z/VM Operating System" <[email protected]>
To
[email protected]
cc
Subject
Re: z/vm dfdss standalone ipl console
Also, some non-VM utilities really want CONMODE 3270. If Mike?s suggestion
doesn?t work, try SET CONMODE 3270 before you IPL 181, eg:
CP SET CONMODE 3270#IPL 181 CLEAR
(the SET CONMODE will cause CMS to choke, so be prepared). Press Enter
after the tape has stopped moving.
From: The IBM z/VM Operating System [mailto:[EMAIL PROTECTED] On
Behalf Of Mike Walter
Sent: Monday, February 11, 2008 1:20 PM
To: [email protected]
Subject: Re: z/vm dfdss standalone ipl console
Some IPLable utilities require an interrupt so that the utility can
identify the specific terminal to which it should reply (this goes back to
ancient days of coax-connected terminals). I'm not sure about DFDSS.
But it can't hurt to try pressing "ENTER" (wherever it is mapped on your
3270 terminal emulator keyboard, but usually the right-Ctrl key).
If that doesn't work, give the ATTN or SysReq key each a try.
If all those fail, try pressing the "PA1" key, which should cause a "CP
READ", then enter: D PSW (or "D PSWG" on z/Architecture virtual machines)
and report back here with the displayed PSW.
Mike Walter
Hewitt Associates
Any opinions expressed herein are mine alone and do not necessarily
represent the opinions or policies of Hewitt Associates.
Caleb <[EMAIL PROTECTED]>
Sent by: "The IBM z/VM Operating System" <[email protected]>
02/11/2008 10:29 AM
Please respond to
"The IBM z/VM Operating System" <[email protected]>
To
[email protected]
cc
Subject
z/vm dfdss standalone ipl console
Hi,
We are running z/VM Version 5 Release 2.0 service level 0702 (64-bit)
We have a standalone z/OS DFDSS 1.7 which we intend to IPL
from a z/VM guest to restore a tape backup to a dasd.
Upon IPL from tape (i.e. IPL 181 clear), we were able to load
the standalone dfdss program successfully:
5694-A01 DFSMSDSS STAND-ALONE v1.07.0 ....
...
ADRY005E DEFINE INPUT DEVICE, REPLY 'DDD,CCUU' OR 'CONSOLE'
ENTER INPUT/COMMAND:
.
We reply to message above with "CONSOLE" ,but the program
just hangs without any error message. z/vm shows the status as "running".
Other programs such as standalone ICKDSF seems to have no problem.
We know our SADFDSS is a working tape because when we ipled without z/vm,
there is no problem replying "CONSOLE" to the ADRY0005E message.
Can anyone guide me on what to check ? thanks.
Caleb
The information contained in this e-mail and any accompanying documents
may contain information that is confidential or otherwise protected from
disclosure. If you are not the intended recipient of this message, or if
this message has been addressed to you in error, please immediately alert
the sender by reply e-mail and then delete this message, including any
attachments. Any dissemination, distribution or other use of the contents
of this message by anyone other than the intended recipient is strictly
prohibited. All messages sent to and from this e-mail address may be
monitored as permitted by applicable law and regulations to ensure
compliance with our internal policies and to protect our business. Emails
are not secure and cannot be guaranteed to be error free as they can be
intercepted, amended, lost or destroyed, or contain viruses. You are
deemed to have accepted these risks if you communicate with us by email.
The information contained in this e-mail and any accompanying documents may
contain information that is confidential or otherwise protected from
disclosure. If you are not the intended recipient of this message, or if this
message has been addressed to you in error, please immediately alert the sender
by reply e-mail and then delete this message, including any attachments. Any
dissemination, distribution or other use of the contents of this message by
anyone other than the intended recipient is strictly prohibited. All messages
sent to and from this e-mail address may be monitored as permitted by
applicable law and regulations to ensure compliance with our internal policies
and to protect our business. Emails are not secure and cannot be guaranteed to
be error free as they can be intercepted, amended, lost or destroyed, or
contain viruses. You are deemed to have accepted these risks if you communicate
with us by email.
