Hello again.
Well, I tried both the starter system default password and the new password I changed it to to logon on as root for the full-service starter system from my SSH client and neither one works. Also, when I logo as root, it does asks for a password. Is there a different default password for root for the full-service server? Thanks, Alyce ________________________________ From: The IBM z/VM Operating System [mailto:[EMAIL PROTECTED] On Behalf Of Scott Rohling Sent: Tuesday, September 30, 2008 3:18 PM To: [email protected] Subject: Re: SLES10 Client Don't be afraid -- you're not going to break anything... And besides - we're here if you do :-) Best of luck - Scott On Tue, Sep 30, 2008 at 4:02 PM, Austin, Alyce (CIV) <[EMAIL PROTECTED]> wrote: I was afraid I might get locked out.... -----Original Message----- From: The IBM z/VM Operating System [mailto:[EMAIL PROTECTED] On Behalf Of Mike Walter Sent: Tuesday, September 30, 2008 2:54 PM To: [email protected] Subject: Re: SLES10 Client Why not just try the default NOVSTART root password and find out for yourself? If it works (which it should) you have your answer. But if you followed the instructions, you changed your NOVSTART root password immediately. So try that one, if the default fails. Mike Walter Hewitt Associates Any opinions expressed herein are mine alone and do not necessarily represent the opinions or policies of Hewitt Associates. "Austin, Alyce (CIV)" <[EMAIL PROTECTED]> Sent by: "The IBM z/VM Operating System" <[email protected]> 09/30/2008 04:33 PM Please respond to "The IBM z/VM Operating System" <[email protected]> To [email protected] cc Subject Re: SLES10 Client OK...i was able to ssh to my new client. Is the default root password the same as it was for the starter system? Thanks, Alyce -----Original Message----- From: The IBM z/VM Operating System [mailto:[EMAIL PROTECTED] On Behalf Of Mike Walter Sent: Tuesday, September 30, 2008 2:20 PM To: [email protected] Subject: Re: SLES10 Client As long as you left it "RUNNING" in the bottom right hand corner of the screen, having issued at some point since logon, (perhaps in the "PROFILE EXEC"), you should be good to SSH in right away. Also, see SHARE session "Installing a Novell SLES 10 Starter System without a Net(work)" at: http://linuxvm.org/Present/SHARE111/S9287mw.pdf some parts may have helped you, and still may. You're right at the end of the session. Mike Walter Hewitt Associates Any opinions expressed herein are mine alone and do not necessarily represent the opinions or policies of Hewitt Associates. "Austin, Alyce (CIV)" <[EMAIL PROTECTED]> Sent by: "The IBM z/VM Operating System" <[email protected]> 09/30/2008 04:01 PM Please respond to "The IBM z/VM Operating System" <[email protected]> To [email protected] cc Subject Re: SLES10 Client OOPs...I already disonnected from "Client" Do I need to start the process again before SSH'g? Thanks, Alyce -----Original Message----- From: The IBM z/VM Operating System [mailto:[EMAIL PROTECTED] On Behalf Of Mark Post Sent: Tuesday, September 30, 2008 1:33 PM To: [email protected] Subject: Re: SLES10 Client >>> On 9/30/2008 at 4:20 PM, in message <[EMAIL PROTECTED]>, "Austin, Alyce (CIV)" <[EMAIL PROTECTED]> wrote: > Hi Everyone, > > Well, I made it to: > > > > *** login using 'ssh -X [EMAIL PROTECTED]' *** > *** run 'yast' to start the installation *** > > > > Am I suppose to disconnect from client and then ssh to it and enter > YAST; or, do I enter YAST from here? Neither. Leave your TN3270 session as it is, since you'll need it later. From your desktop, SSH to the IP address shown in the message, then issue the yast command. Mark Post The information contained in this e-mail and any accompanying documents may contain information that is confidential or otherwise protected from disclosure. If you are not the intended recipient of this message, or if this message has been addressed to you in error, please immediately alert the sender by reply e-mail and then delete this message, including any attachments. Any dissemination, distribution or other use of the contents of this message by anyone other than the intended recipient is strictly prohibited. All messages sent to and from this e-mail address may be monitored as permitted by applicable law and regulations to ensure compliance with our internal policies and to protect our business. E-mails are not secure and cannot be guaranteed to be error free as they can be intercepted, amended, lost or destroyed, or contain viruses. You are deemed to have accepted these risks if you communicate with us by e-mail. The information contained in this e-mail and any accompanying documents may contain information that is confidential or otherwise protected from disclosure. If you are not the intended recipient of this message, or if this message has been addressed to you in error, please immediately alert the sender by reply e-mail and then delete this message, including any attachments. Any dissemination, distribution or other use of the contents of this message by anyone other than the intended recipient is strictly prohibited. All messages sent to and from this e-mail address may be monitored as permitted by applicable law and regulations to ensure compliance with our internal policies and to protect our business. E-mails are not secure and cannot be guaranteed to be error free as they can be intercepted, amended, lost or destroyed, or contain viruses. You are deemed to have accepted these risks if you communicate with us by e-mail.
