If I've understood correctly you're trying to define AHHC MPC CTC links. You'll need to define and activate a LOCAL PU mapped to the TRLE before the TRLE becomes active.
As William said, be careful to understand if you need to cross-over the READ-WRITE device addresses. Regards, Mike Mike Wawiorko Global z/OS Connectivity and Service Management GISD Platforms GRCB Technology Barclays Bank Ground Floor (C6), Turing House, Radbroke Hall, WA16 9EU (Mail Van 49) Tel: +44(0)1565 613467 or internal 7-2000-3467 Mobile: 07824527120 Email: mailto:[email protected] <mailto:[email protected]> P Please consider the environment before printing this e-mail _____ From: The IBM z/VM Operating System [mailto:[email protected]] On Behalf Of Boyer, William Sent: 04 June 2009 16:48 To: [email protected] Subject: Virtual Devices for VTAM in RESET status We are attempting to move from SNA network to APPN. We have two guest ZOS systems which I have executed a DEFINE CTCA 200 and DEFINE CTCA 201 on both systems. I issued the COUPLE 200 TO ZOSB 200 and COUPLE 201 TO ZOSB 201 from ZOSA. The addresses are defined in the HCD for both ZOS systems. We currently do a similar connection for the SNA connection. When vary the TRL active on ZOS and then display the LINE it is showing the Channel in RESET status and the line does not come active. Did I miss something in the VM virtual device definitions? Is there a way of clearing the RESET status. Here is the display of the LINE from ZOS. D NET,ID=TRLEZOSA IST097I DISPLAY ACCEPTED IST075I NAME = TRLEZOSA, TYPE = TRLE IST486I STATUS= NEVAC, DESIRED STATE= INACT IST087I TYPE = LEASED , CONTROL = MPC , HPDT = *NA* IST1954I TRL MAJOR NODE = TRLZOSA IST1715I MPCLEVEL = HPDT MPCUSAGE = SHARE IST1221I WRITE DEV = 0200 STATUS = RESET STATE = N/A IST1221I READ DEV = 0201 STATUS = RESET STATE = N/A IST1500I STATE TRACE = OFF IST314I END William Boyer Principal Administrator, Mainframe Systems ViPS, a General Dynamics Information Technology Company Business & Technology Services One West Pennsylvania Avenue Baltimore, MD 21204 Tel. 410.832.8300 Fax. 410.832.8329 <mailto:[email protected]> [email protected] <http://www.vips.com/> www.vips.com This message is confidential, intended only for the named recipient (s) and may contain information that is privileged or exempt from disclosure under applicable law. If you are not the intended recipient (s), you are notified that the dissemination, distribution or copying of this message is strictly prohibited. If you receive this message in error or are not the named recipient (s), please notify the sender at either the fax address or telephone number above and delete this message. Thank you. This e-mail and any attachments are confidential and intended solely for the addressee and may also be privileged or exempt from disclosure under applicable law. If you are not the addressee, or have received this e-mail in error, please notify the sender immediately, delete it from your system and do not copy, disclose or otherwise act upon any part of this e-mail or its attachments. Internet communications are not guaranteed to be secure or virus-free. The Barclays Group does not accept responsibility for any loss arising from unauthorised access to, or interference with, any Internet communications by any third party, or from the transmission of any viruses. Replies to this e-mail may be monitored by the Barclays Group for operational or business reasons. Any opinion or other information in this e-mail or its attachments that does not relate to the business of the Barclays Group is personal to the sender and is not given or endorsed by the Barclays Group. Barclays Bank PLC.Registered in England and Wales (registered no. 1026167). Registered Office: 1 Churchill Place, London, E14 5HP, United Kingdom. Barclays Bank PLC is authorised and regulated by the Financial Services Authority.
