Having spoken to a number of the authors at length
I think the text changes that Matthew has proposed
are correct (with Greg's change) and thank the authors
for picking this up.
I propose to let this sit until a week tomorrow (23/Feb)
and provided that there are no technical issues with the
proposed changes I will ask the RFC Editor to make
the changes and to publish the RFC.
- Stewart
On 16/02/2012 10:02, Bocci, Matthew (Matthew) wrote:
Greg,
That is fine with me.
Best regards
Matthew
On 15/02/2012 22:14, "Gregory Mirsky" <gregory.mir...@ericsson.com
<mailto:gregory.mir...@ericsson.com>> wrote:
Dear Matthew, Authors, et al.,
I think that new text of fourth para in Section 5.3 adds some
confusion. If intension is to stop sending 'all clear' after three
one-second intervals went unacknowledged but before refresh timer
expires then perhpas new text can be more explicit:
NEW:
To clear a particular status fault, the PE need only send an
updated message with the corresponding bit cleared. If the PW status
code is zero, the PW OAM message will be sent like any other PW OAM
status message using the procedures described above; however,
transmission will cease after 3 PW status messages have been
sent/_at one second intervals and before refresh timer expires_/. A PW
status message of zero MAY be acknowledged as per the procedures
described
in Section 5.3.1. If it is acknowledged, then a timer
value of zero MUST be used. This SHOULD cause the PE sending the
PW status
notification message with a PW status code equal to zero to stop
sending
and to continue normal operation.
Regards,
Greg
------------------------------------------------------------------------
*From:* pwe3-boun...@ietf.org <mailto:pwe3-boun...@ietf.org>
[mailto:pwe3-boun...@ietf.org] *On Behalf Of *Bocci, Matthew (Matthew)
*Sent:* Wednesday, February 15, 2012 7:10 AM
*To:* p...@ietf.org <mailto:p...@ietf.org>; ietf@ietf.org
<mailto:ietf@ietf.org>
*Cc:* pwe3-cha...@tools.ietf.org
<mailto:pwe3-cha...@tools.ietf.org>; Stewart Bryant
*Subject:* [PWE3] Auth48 comments on
draft-ietf-pwe3-static-pw-status-10
During Auth 48, the authors of draft-ietf-pwe3-static-pw-status
found some issues with the acknowledgement procedures in Section
5.3 of the draft that we feel should be addressed before
publication. Since the draft has already been through WG and IETF
last call, we would like to highlight the proposed changes to the
working group and solicit feedback.
Best regards,
Matthew
Section 5.3, 3rd paragraph:
Reason for change:
The current suggested default refresh timer value is too short to
allow scaling
to very large numbers of PWs while minimising the overhead. It is
also inconsistent
with the suggested default requested in an ACK packet. Therefore
we suggest increasing
the default to 600secs.
OLD: The suggested default value for the refresh timer is 30 seconds.
NEW: The suggested default value for the refresh timer is 600 seconds.
Section 5.3, 4th paragraph:
Reason for change:
The current text requires that a receiving PE must acknowledge a
PW status message
of 'clear all faults' in order to force a transmitter to stop
sending PW status
messages at 1 second intervals. We are concerned that a mandatory
acknowledgement
adds an unnecessary complexity to the protocol which is
inconsistent with
the use of the acknowledgement as per the following section
(5.3.1). Additionally,
we are also concerned that this may cause problems if a transmitter
is flapping between 'clear all faults' and a non-zero value, and
if the
acknowledgement is lost. We therefore suggest that the
acknowledgement to
'clear all faults' be made optional, and that the transmitter
behavior be changed so
that it sends up to 3 status messages of zero in a row, and then
goes silent.
OLD:
To clear a particular status fault, the PE need only send an
updated message with the corresponding bit cleared. If the PW status
code is zero, the PW OAM message will be sent like any other PW OAM
status message using the procedures described above; however, it
MUST be
acknowledged with a packet with a timer value of zero. This will
cause
the PE sending the PW status notification message with a PW status
code
equal to zero to stop sending and to continue normal operation.
NEW:
To clear a particular status fault, the PE need only send an
updated message with the corresponding bit cleared. If the PW status
code is zero, the PW OAM message will be sent like any other PW OAM
status message using the procedures described above; however,
transmission will cease after 3 PW status messages have been sent.
A PW
status message of zero MAY be acknowledged as per the procedures
described
in Section 5.3.1. If it is acknowledged, then a timer
value of zero MUST be used. This SHOULD cause the PE sending the
PW status
notification message with a PW status code equal to zero to stop
sending
and to continue normal operation.
Section 5.3.1, 1st paragraph:
Reason for change:
The procedures currently defined in this paragraph can lead to a
receiver
of the static status message timing out if it requests, throught
the use of the
ACK mechanism, a longer refresh timer from the transmitter. This
is because the
current text implies that the transmitter change its referesh
timer immediately
on receipt of the ack packet from the receiver. The new text
clarifies that
the refresh timer be updated at the end of the current refresh
interval, as
well as making some other editorial clarifications.
OLD:
The PE receiving a PW OAM message containing a PW status message
can acknowledge the PW status message by simply building an almost
identical reply packet with the A bit set, and transmitting it on
the PW
ACH back to the source of the PW status message. The timer value
set in
the reply packet SHOULD then be used by the PE as the new transmit
interval. If the transmitting PE does not want to use the new timer
value (for local policy reasons, or because it simply cannot support
it), it MUST refresh the PW OAM message with the timer value it
desires.
The receiving PE will then set its timeout timer according to the
timer
value that is in the packet received, regardless of what timer
value it
sent. The receiving PE MUST NOT retry to set the timer value more
than
once per timer value.
NEW:
A PE receiving a PW OAM message containing a PW status message MAY
acknowledge the PW status message by simply building a reply packet
with the same format and status code as the received PW OAM message,
but with the A bit set, and transmitting it on the PW ACh back
to the source of the PW OAM message. The receiving PE MAY use the
refresh timer field in the acknowledgement packet to request a new
refresh interval from the originator of the PW OAM message. The timer
value set in the reply packet SHOULD then be used by the originator of
the PW OAM message as the new transmit interval. If the requested
refresh timer value is used, the PW OAM message transmission
interval is
only set to the new value and the new value sent in the next PW OAM
message, when the current timer expires. If the transmitting PE
does not
want to use the new timer value (for local policy reasons, or
because it
simply cannot support it), it MUST refresh the PW OAM message with the
timer value it desires. The receiving PE will then set its timeout
timer
according to the new refresh timer value that is in the packet
received,
regardless of what timer value it requested. The receiving PE
MUST NOT
request a new refresh timer value more than once per refresh interval.
--
For corporate legal information go to:
http://www.cisco.com/web/about/doing_business/legal/cri/index.html
_______________________________________________
Ietf mailing list
Ietf@ietf.org
https://www.ietf.org/mailman/listinfo/ietf