Hi All, I finally got the Tata Indicom Plug2Surf Whiz USB modem. Now I am unable to get it started. Below are some details.
dmesg output: usb 5-1: new full speed USB device using uhci_hcd and address 2 usb 5-1: device descriptor read/64, error -71 usb 5-1: device descriptor read/64, error -71 usb 5-1: new full speed USB device using uhci_hcd and address 3 usb 5-1: new full speed USB device using uhci_hcd and address 4 usb 5-1: configuration #1 chosen from 1 choice usb 5-1: New USB device found, idVendor=1b7d, idProduct=070a usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 5-1: Product: Qualcomm CDMA Technologies MSM usb 5-1: Manufacturer: Qualcomm, Incorporated cdc_acm 5-1:1.0: ttyACM0: USB ACM device usbcore: registered new interface driver cdc_acm drivers/usb/class/cdc-acm.c: v0.25:USB Abstract Control Model driver for USB modems and ISDN adapters cat /proc/bus/usb/devices ... T: Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 9 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=02(comm.) Sub=00 Prot=00 MxPS=16 #Cfgs= 1 P: Vendor=1b7d ProdID=070a Rev= 0.00 S: Manufacturer=Qualcomm, Incorporated S: Product=Qualcomm CDMA Technologies MSM C:* #Ifs= 3 Cfg#= 1 Atr=c0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=02 Prot=01 Driver=cdc_acm E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=32ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_acm E: Ad=8a(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=0b(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=00 Driver=usbserial_generic E: Ad=83(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms ... #modprobe usbserial vendor=0x1b7d product=0x070a #lsmod |grep -i usb usbserial 40272 0 hci_usb 23068 2 bluetooth 59044 8 bnep,rfcomm,l2cap,hci_usb #wvdialconf #cat /etc/wvdial.conf [Dialer Defaults] Init1 = ATZ Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 Modem Type = USB Modem Phone = #777 ISDN = 0 Username = internet Password = internet Modem = /dev/ttyACM0 Baud = 460800 ; SetVolume = 0 ; FlowControl = Hardware (CRTSCTS) ; Dial Command = ATDT Stupid Mode = 1 #wvdial --> WvDial: Internet dialer version 1.60 --> Cannot get information for serial port. --> Initializing modem. --> Sending: ATZ ATZ OK --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 OK --> Modem initialized. --> Sending: ATDT#777 --> Waiting for carrier. ATDT#777 CONNECT --> Carrier detected. Starting PPP immediately. --> Starting pppd at Sat Dec 20 18:10:10 2008 --> Pid of pppd: 5386 --> Using interface ppp0 --> pppd: 2 --> pppd: 2 --> pppd: 2 --> pppd: 2 --> pppd: 2 --> Disconnecting at Sat Dec 20 18:10:41 2008 --> The PPP daemon has died: A modem hung up the phone (exit code = 16) --> man pppd explains pppd error codes in more detail. --> Try again and look into /var/log/messages and the wvdial and pppd man pages for more information. --> Auto Reconnect will be attempted in 5 seconds --> Cannot get information for serial port. --> Initializing modem. --> Sending: ATZ ATZ OK --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 OK ... /var/log/messages Dec 20 18:00:31 av1984 pppd[5233]: pppd 2.4.4 started by root, uid 0 Dec 20 18:00:31 av1984 pppd[5233]: Using interface ppp0 Dec 20 18:00:31 av1984 pppd[5233]: Connect: ppp0 <--> /dev/ttyACM0 Dec 20 18:00:34 av1984 pppd[5233]: Terminating on signal 15 Dec 20 18:10:10 av1984 pppd[5386]: pppd 2.4.4 started by root, uid 0 Dec 20 18:10:10 av1984 pppd[5386]: Using interface ppp0 Dec 20 18:10:10 av1984 pppd[5386]: Connect: ppp0 <--> /dev/ttyACM0 Dec 20 18:10:40 av1984 pppd[5386]: LCP: timeout sending Config-Requests Dec 20 18:10:40 av1984 pppd[5386]: Connection terminated. Dec 20 18:10:40 av1984 pppd[5386]: Modem hangup Dec 20 18:10:40 av1984 pppd[5386]: Exit. Dec 20 18:10:46 av1984 pppd[5404]: pppd 2.4.4 started by root, uid 0 Dec 20 18:10:46 av1984 pppd[5404]: Using interface ppp0 Dec 20 18:10:46 av1984 pppd[5404]: Connect: ppp0 <--> /dev/ttyACM0 Dec 20 18:10:48 av1984 pppd[5404]: Terminating on signal 15 I also tried to create a tata file in init.d, as mentioned in http://www.indiangnu.org/2008/tata-indicom-usb-modem-epi-valley-on-ubuntu-linux/. but then got the below error. service tata start stop: missing job name Try `stop --help' for more information. /etc/init.d/tata: line 36: status}": command not found I do not run the NetworkManager instead just use the network service. Please help. Regards, Ashish _______________________________________________ To unsubscribe, email [email protected] with "unsubscribe <password> <address>" in the subject or body of the message. http://www.ae.iitm.ac.in/mailman/listinfo/ilugc
