----- Original Message ----- From: "Vignesh Rajendran" <[email protected]> To: "ILUG-C" <[email protected]> Sent: Wednesday, September 26, 2012 6:44:47 PM Subject: Re: [Ilugc] key board & Mouse not working with CENTOS 6.0
On Wed, Sep 26, 2012 at 1:02 PM, <[email protected]> wrote: > Hi > > As the USB devices are becoming inactive during the runlelvel 5, I had to > switch over to runlevel 1 to trouble shoot it. But here the nework is not > active. Hence, I am clueless as to what to do further? > Why you looking for usb devices.Anyway we only need that log,right.Do ssh to this box and get the log from neighbour PC. > > with thanx > s.mahalingam > > > ----- Original Message ----- > From: "Vignesh Rajendran" <[email protected]> > To: "ILUG-C" <[email protected]> > Sent: Wednesday, September 26, 2012 6:27:08 PM > Subject: Re: [Ilugc] key board & Mouse not working with CENTOS 6.0 > > On Wed, Sep 26, 2012 at 12:08 PM, <[email protected]> wrote: > > > Hi > > > > Thanx for your reply. On runlevel 1, the network is not active and is not > > reachable/inaccessible over the network to transfer the contents of the > > /var/log/Xorg.0.log files. What Shall I do further? > > > > K. boot in runlevel 5 and do ssh with ip address. > > > > > > with thanx > > s.mahalingam > > > > ----- Original Message ----- > > From: "Vignesh Rajendran" <[email protected]> > > To: "ILUG-C" <[email protected]> > > Sent: Wednesday, September 26, 2012 3:09:57 PM > > Subject: Re: [Ilugc] key board & Mouse not working with CENTOS 6.0 > > > > On Wed, Sep 26, 2012 at 7:01 AM, <[email protected]> wrote: > > > > > Hi > > > > > > All of a sudden the key board & mouse were not working with machine > > loaded > > > with CENTOS 6.0. I had checked with bios settings while booting and > could > > > not find any fault with factory settings. > > > could anybody guide further to find a solution to this? The machine is > > > DELL OPTIPLEX GX620. > > > > > > > Did you update xorg-server?It seems like a problem with Xorg. The newer X > > have the feature of hotplug support of adding input devices.Please switch > > to single user mode and check any /dev/input/event files present.If the > > files are there, post the contents of /var/log/Xorg.log in pastebin site > > and send the link to list.Please dont paste the log in list > > > > > > > > > > with thanks in advance > > > S mahalingam > > > > > > _______________________________________________ > > > ILUGC Mailing List: > > > http://www.ae.iitm.ac.in/mailman/listinfo/ilugc > > > > > > > > > > > > -- > > *Regards > > > > Vignesh Rajendran > > * > > > > *“Learning never exhausts the mind” > > -- Leonardo da Vinci--* > > _______________________________________________ > > ILUGC Mailing List: > > http://www.ae.iitm.ac.in/mailman/listinfo/ilugc > > > > _______________________________________________ > > ILUGC Mailing List: > > http://www.ae.iitm.ac.in/mailman/listinfo/ilugc > > > > > > > -- > *Regards > > Vignesh Rajendran > * > > *“Learning never exhausts the mind” > -- Leonardo da Vinci--* > _______________________________________________ > ILUGC Mailing List: > http://www.ae.iitm.ac.in/mailman/listinfo/ilugc > > _______________________________________________ > ILUGC Mailing List: > http://www.ae.iitm.ac.in/mailman/listinfo/ilugc Hi sorry to say that the default machine is not accessible through N/W. However, booting through run level 1, I could check the contents displayed using "lsusb" command as follows, Bus 002 Device 002: ID 413C:2003 Dell Computer Corp. keyboard Bus 002 Device 003: ID 413C:3010 Dell Computer Corp. Optical Wheel Mouse with thanx s.mahalingam -- *Regards Vignesh Rajendran * *“Learning never exhausts the mind” -- Leonardo da Vinci--* _______________________________________________ ILUGC Mailing List: http://www.ae.iitm.ac.in/mailman/listinfo/ilugc
<<attachment: smal.vcf>>
_______________________________________________ ILUGC Mailing List: http://www.ae.iitm.ac.in/mailman/listinfo/ilugc
