On 18/03/2025 5:07, Faizal Rahim wrote:
This patch implements the "ethtool --set-mm" callback to trigger the frame preemption verification handshake.Uses the MAC Merge Software Verification (mmsv) mechanism in ethtool to perform the verification handshake for igc. The structure fpe.mmsv is set by mmsv in ethtool and should remain read-only for the driver. Other mmsv callbacks: a) configure_tx() -> not used yet at this point - igc lacks registers to configure FPE in the transmit direction, so this API is not utilized for now. When igc supports preemptible queue, driver will use this API to manage its configuration. b) configure_pmac() -> not used - this callback dynamically controls pmac_enabled at runtime. For example, mmsv calls configure_pmac() and disables pmac_enabled when the link partner goes down, even if the user previously enabled it. The intention is to save power but it is not feasible in igc because it causes an endless adapter reset loop: 1) Board A and Board B complete the verification handshake. Tx mode register for both boards are in TSN mode. 2) Board B link goes down. On Board A: 3) mmsv calls configure_pmac() with pmac_enabled = false. 4) configure_pmac() in igc updates a new field based on pmac_enabled. Driver uses this field in igc_tsn_new_flags() to indicate that the user enabled/disabled FPE. 5) configure_pmac() in igc calls igc_tsn_offload_apply() to check whether an adapter reset is needed. Calls existing logic in igc_tsn_will_tx_mode_change() and igc_tsn_new_flags(). 6) Since pmac_enabled is now disabled and no other TSN feature is active, igc_tsn_will_tx_mode_change() evaluates to true because Tx mode will switch from TSN to Legacy. 7) Driver resets the adapter. 8) Registers are set, and Tx mode switches to Legacy. 9) When link partner is up, steps 3–8 repeat, but this time with pmac_enabled = true, reactivating TSN. igc_tsn_will_tx_mode_change() evaluates to true again, since Tx mode will switch from Legacy to TSN. 10) Driver resets the adapter. 11) Adapter reset completes, registers are set, and Tx mode switches to TSN. On Board B: 12) Adapter reset on Board A at step 10 causes it to detect its link partner as down. 13) Repeats steps 3–8. 14) Once reset adapter on Board A is completed at step 11, it detects its link partner as up. 15) Repeats steps 9–11. - this cycle repeats indefinitely. To avoid this issue, igc only uses mmsv.pmac_enabled to track whether FPE is enabled or disabled. Co-developed-by: Vinicius Costa Gomes <[email protected]> Signed-off-by: Vinicius Costa Gomes <[email protected]> Co-developed-by: Choong Yong Liang <[email protected]> Signed-off-by: Choong Yong Liang <[email protected]> Co-developed-by: Chwee-Lin Choong <[email protected]> Signed-off-by: Chwee-Lin Choong <[email protected]> Reviewed-by: Vladimir Oltean <[email protected]> Signed-off-by: Faizal Rahim <[email protected]> --- drivers/net/ethernet/intel/Kconfig | 1 + drivers/net/ethernet/intel/igc/igc.h | 12 +- drivers/net/ethernet/intel/igc/igc_base.h | 1 + drivers/net/ethernet/intel/igc/igc_defines.h | 8 +- drivers/net/ethernet/intel/igc/igc_ethtool.c | 21 +++ drivers/net/ethernet/intel/igc/igc_main.c | 52 ++++++- drivers/net/ethernet/intel/igc/igc_tsn.c | 146 ++++++++++++++++++- drivers/net/ethernet/intel/igc/igc_tsn.h | 50 +++++++ 8 files changed, 286 insertions(+), 5 deletions(-)
Tested-by: Mor Bar-Gabay <[email protected]>
