The Intel IOMMU driver reports the DMA fault reason in a decimal number while the VT-d specification uses a hexadecimal one. It's inconvenient that users need to covert them everytime before consulting the spec. Let's use hexadecimal number for a DMA fault reason.
The fault message uses 0xffffffff as PASID for DMA requests w/o PASID. This is confusing. Tweak this by adding "NO_PASID" explicitly. Reviewed-by: Ashok Raj <[email protected]> Signed-off-by: Lu Baolu <[email protected]> --- drivers/iommu/intel/dmar.c | 23 +++++++++++++++-------- 1 file changed, 15 insertions(+), 8 deletions(-) Change log: v1->v2: - Add "0x" prefix to all hex numbers diff --git a/drivers/iommu/intel/dmar.c b/drivers/iommu/intel/dmar.c index 1757ac1e1623..1e31e6799d5c 100644 --- a/drivers/iommu/intel/dmar.c +++ b/drivers/iommu/intel/dmar.c @@ -1911,16 +1911,23 @@ static int dmar_fault_do_one(struct intel_iommu *iommu, int type, reason = dmar_get_fault_reason(fault_reason, &fault_type); if (fault_type == INTR_REMAP) - pr_err("[INTR-REMAP] Request device [%02x:%02x.%d] fault index %llx [fault reason %02d] %s\n", - source_id >> 8, PCI_SLOT(source_id & 0xFF), - PCI_FUNC(source_id & 0xFF), addr >> 48, - fault_reason, reason); - else - pr_err("[%s] Request device [%02x:%02x.%d] PASID %x fault addr %llx [fault reason %02d] %s\n", + pr_err("[INTR-REMAP] Request device [0x%02x:0x%02x.%d] fault index 0x%llx [fault reason 0x%02x] %s\n", + source_id >> 8, PCI_SLOT(source_id & 0xFF), + PCI_FUNC(source_id & 0xFF), addr >> 48, + fault_reason, reason); + else if (pasid == INVALID_IOASID) + pr_err("[%s NO_PASID] Request device [0x%02x:0x%02x.%d] fault addr 0x%llx [fault reason 0x%02x] %s\n", type ? "DMA Read" : "DMA Write", source_id >> 8, PCI_SLOT(source_id & 0xFF), - PCI_FUNC(source_id & 0xFF), pasid, addr, + PCI_FUNC(source_id & 0xFF), addr, fault_reason, reason); + else + pr_err("[%s PASID 0x%x] Request device [0x%02x:0x%02x.%d] fault addr 0x%llx [fault reason 0x%02x] %s\n", + type ? "DMA Read" : "DMA Write", pasid, + source_id >> 8, PCI_SLOT(source_id & 0xFF), + PCI_FUNC(source_id & 0xFF), addr, + fault_reason, reason); + return 0; } @@ -1987,7 +1994,7 @@ irqreturn_t dmar_fault(int irq, void *dev_id) if (!ratelimited) /* Using pasid -1 if pasid is not present */ dmar_fault_do_one(iommu, type, fault_reason, - pasid_present ? pasid : -1, + pasid_present ? pasid : INVALID_IOASID, source_id, guest_addr); fault_index++; -- 2.25.1 _______________________________________________ iommu mailing list [email protected] https://lists.linuxfoundation.org/mailman/listinfo/iommu
