1. Do you have any module options specified? 2. Make sure you are using the newest firmware versions: http://ivtvdriver.org/index.php/Firmware
On 10/10/05, Johan Asterholm <[EMAIL PROTECTED]> wrote: > Hi, > > I have two different hauppauge cards, and i have problems with both of them. > > I live in Sweden and uses Europe-pal. using .0.4.0 > > First of is a PVR-250. With this one i get a nice clear picture, but > no sound (except for one channel. > > it has a label with PAL-B/G-I-D/K-SECAM 32059. > > Output from dmesg can be found below. > > The second card is a PVR-500 where i have sound, but quite bad > reception (some channels are better than the others). Same thing on > both tuners. > > This one has the following under the sticker on one of the tuner: > > FQ1216AME/R H-4 > > The output from dmesg can be found below. > > Any help would be appreciated allot! > > BR / Johan > > ivtv: ==================== START INIT IVTV ==================== > ivtv: version 0.4.0 (tagged release) loading > ivtv: Linux version: 2.6.10-5-686-smp SMP preempt 686 gcc-3.3 > ivtv: In case of problems please include the debug info > ivtv: between the START INIT IVTV and END INIT IVTV lines when > ivtv: mailing the ivtv-devel mailinglist. > ivtv0: Autodetected WinTV PVR 250 card (iTVC16 based) > ACPI: PCI interrupt 0000:02:0a.0[A] -> GSI 22 (level, low) -> IRQ 22 > tveeprom: ivtv version > tveeprom: Hauppauge: model = 32059, rev = B143, serial# = 7263640 > tveeprom: tuner = Temic 4046FM5 (idx = 43, type = 22) > tveeprom: tuner fmt = PAL(B/G) PAL(I) SECAM(L/L') PAL(D/K) (eeprom = > 0x74, v4l2 = 0x00400e17) > tveeprom: audio processor = MSP4418 (type = 19) > tveeprom: decoder processor = SAA7115 (type = 13) > ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50] > tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 > ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61] > saa7115 1-0021: saa7115 found @ 0x42 (ivtv i2c driver #0) > ivtv0: i2c attach to card #0 ok [client=saa7115, addr=21] > msp34xx: ivtv version > msp34xx: init: chip=MSP3418W-A2, has NICAM support, simple (D) mode, > simpler (G) no-thread mode > msp34xx: $Id$ compiled on: Oct 10 2005 17:44:36 > ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e01800008d7503] > ivtv0: i2c attach to card #0 ok [client=MSP3418W-A2, addr=40] > ivtv0: loading /lib/modules/ivtv-fw-enc.bin > ivtv0: Encoder revision: 0x02040011 > ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) > ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total) > ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total) > ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB > total) > tuner: type set to 22 (Temic PAL/SECAM multi (4046 FM5)) by ivtv i2c driver #0 > ivtv0: Initialized WinTV PVR 250, card #0 > ivtv: ====================== NEXT CARD ====================== > ivtv1: Autodetected WinTV PVR 150 card (iTVC16 based) > ACPI: PCI interrupt 0000:03:08.0[A] -> GSI 21 (level, low) -> IRQ 21 > tveeprom: Second (radio) tuner idx 101 > tveeprom: ivtv version > tveeprom: Hauppauge: model = 23559, rev = D591, serial# = 2989473 > tveeprom: tuner = Philips FQ1216AME MK4 (idx = 91, type = 56) > tveeprom: tuner fmt = PAL(B/G) PAL(I) SECAM(L/L') PAL(D/K) (eeprom = > 0x74, v4l2 = 0x00400e17) > tveeprom: audio processor = CX25843 (type = 25) > tveeprom: decoder processor = CX25843 (type = 1e) > ivtv1: i2c attach to card #1 ok [client=tveeprom, addr=50] > tuner (ivtv): chip found at addr 0xc0 i2c-bus ivtv i2c driver #1 > TEA5767 detected. > ivtv1: i2c attach to card #1 ok [client=(tuner unset), addr=60] > tuner: type set to 62 (Philips TEA5767HN FM Radio) by autodetect > type set to 62 (Philips TEA5767HN FM Radio) > tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #1 > ivtv1: i2c attach to card #1 ok [client=(tuner unset), addr=61] > tda9885/6/7: (ivtv) chip found @ 0x86 > ivtv1: i2c attach to card #1 ok [client=tda9887, addr=43] > ivtv1: This is the first unit of a PVR500 > cx25840 2-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #1) > cx25840 2-0044: loaded /lib/modules/HcwMakoA.ROM firmware (14264 bytes) > ivtv1: i2c attach to card #1 ok [client=cx25840, addr=44] > wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #1) > ivtv1: i2c attach to card #1 ok [client=wm8775, addr=1b] > ivtv1: Detected a TEA5767 radio tuner. Enabling radio support. > ivtv1: loading /lib/modules/ivtv-fw-enc.bin > ivtv1: Encoder revision: 0x02040011 > ivtv1: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) > ivtv1: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total) > ivtv1: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total) > ivtv1: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB > total) > ivtv1: Create encoder radio stream > tuner: type set to 56 (Philips PAL/SECAM multi (FQ1216AME MK4)) by > ivtv i2c driver #1 > ivtv1: Initialized WinTV PVR 500 (unit #1), card #1 > ivtv: ====================== NEXT CARD ====================== > ivtv2: Autodetected WinTV PVR 150 card (iTVC16 based) > ACPI: PCI interrupt 0000:03:09.0[A] -> GSI 22 (level, low) -> IRQ 22 > tveeprom: Second (radio) tuner idx 101 > tveeprom: ivtv version > tveeprom: Hauppauge: model = 23559, rev = D591, serial# = 2989473 > tveeprom: tuner = Philips FQ1216AME MK4 (idx = 91, type = 56) > tveeprom: tuner fmt = PAL(B/G) PAL(I) SECAM(L/L') PAL(D/K) (eeprom = > 0x74, v4l2 = 0x00400e17) > tveeprom: audio processor = CX25843 (type = 25) > tveeprom: decoder processor = CX25843 (type = 1e) > ivtv2: i2c attach to card #2 ok [client=tveeprom, addr=50] > tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #2 > ivtv2: i2c attach to card #2 ok [client=(tuner unset), addr=61] > tda9885/6/7: (ivtv) chip found @ 0x86 > ivtv2: i2c attach to card #2 ok [client=tda9887, addr=43] > cx25840 3-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #2) > cx25840 3-0044: loaded /lib/modules/HcwMakoA.ROM firmware (14264 bytes) > ivtv2: i2c attach to card #2 ok [client=cx25840, addr=44] > wm8775 3-001b: chip found @ 0x36 (ivtv i2c driver #2) > ivtv2: i2c attach to card #2 ok [client=wm8775, addr=1b] > ivtv2: This is the second unit of a PVR500 > ivtv2: Correcting tveeprom data: no radio present on second unit > ivtv2: loading /lib/modules/ivtv-fw-enc.bin > ivtv2: Encoder revision: 0x02040011 > ivtv2: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) > ivtv2: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total) > ivtv2: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total) > ivtv2: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB > total) > tuner: type set to 56 (Philips PAL/SECAM multi (FQ1216AME MK4)) by > ivtv i2c driver #2 > ivtv2: Initialized WinTV PVR 500 (unit #2), card #2 > ivtv: ==================== END INIT IVTV ==================== > > _______________________________________________ > ivtv-devel mailing list > [email protected] > http://ivtvdriver.org/mailman/listinfo/ivtv-devel > _______________________________________________ ivtv-devel mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-devel
