Tyler Trafford wrote: > Hans Verkuil wrote: > >>On Sunday 27 November 2005 20:24, Sigurd Nes wrote: >> >> >>>Hans Verkuil wrote: >>> >>> >>>>On Sunday 27 November 2005 19:23, Sigurd Nes wrote: >>>> >>>> >>>>>Hans Verkuil wrote: >>>>> >>>>> >>>>>>Have you tested r2950 and r2961? Please provide the results for >>>>>>these specific revisions. My guess is that 2950 works and 2961 >>>>>>doesn't, but I need the test results for these revisions. >>>>>> >>>>>>If my guess is wrong, then please report that. If I am correct, >>>>>>then I'd like you to do the following test with r2961: >>>>>> >>>>>>Before loading ivtv, first load the tuner with 'modprobe tuner >>>>>>tuner_debug=1', and then load ivtv. Select a known channel and >>>>>>again run ivtvctl --log-status. Please post the kernel log >>>>>>starting with the debug tuner messages from the channel change. >>>>>>It all looks like something is wrong with the tuner settings. >>>>>> >>>>>>Oh, and don't use MythTV. Use ivtv-tune to select the channel and >>>>>>just run 'cat /dev/videoX >test.mpg' to capture video. Look at it >>>>>>with xine or mplayer. Nothing wrong with MythTV but I prefer to >>>>>>keep the chain of events as short as possible. >>>>>> >>>>>> Hans >>>>> >>>>>I did this to r3007 (I will check r2961 when the kids are put to >>>>>bed) >>>>> >>>>>/sbin/modprobe tuner tuner_debug=1 >>>>>/sbin/modprobe ivtv ivtv_std=2 ivtv_debug=1 >>>>> >>>>>'ivtvctl -d /dev/video2 --log-status' gives: >>>>>ivtv2: ================= START STATUS CARD #2 ================= >>>>>cx25840 2-0044: Video signal: not present >>>>>cx25840 2-0044: Detected format: NTSC-M >>>>>cx25840 2-0044: Detected audio mode: mono >>>>>cx25840 2-0044: Detected audio standard: no detected audio >>>>>standard cx25840 2-0044: Audio muted: yes >>>>>cx25840 2-0044: Audio microcontroller: running >>>>>cx25840 2-0044: Configured audio standard: automatic detection >>>>>cx25840 2-0044: Configured audio system: automatic standard and >>>>>mode detection >>>>>cx25840 2-0044: Specified standard: PAL-BDGHI >>>>>cx25840 2-0044: Specified input: Tuner >>>>>cx25840 2-0044: Specified audio input: Tuner >>>>>cx25840 2-0044: Specified audioclock freq: 48 kHz >>>>>cx25840 2-0044: Preferred audio mode: stereo >>>>>cx25840 2-0044: Selected 65 MHz format: autodetect >>>>>cx25840 2-0044: Selected 45 MHz format: chroma >>>>>wm8775 2-001b: Input: default >>>>>tda9887 2-0043: Data bytes: b=d4 c=70 e=09 >>>>>ivtv2: ================== END STATUS CARD #2 ================== >>>>> >>>>>Static - no sound >>>>> >>>>>'ivtv-tune -t europe-west -d /dev/video2 -c E8' >>>>>and >>>>>'ivtvctl -d /dev/video2 --log-status' gives: >>>>> >>>>>ivtv2: ================= START STATUS CARD #2 ================= >>>>>cx25840 2-0044: Video signal: present >>>>>cx25840 2-0044: Detected format: PAL-BDGHI >>>>>cx25840 2-0044: Detected audio mode: stereo >>>>>cx25840 2-0044: Detected audio standard: NICAM-BG >>>>>cx25840 2-0044: Audio muted: no >>>>>cx25840 2-0044: Audio microcontroller: running >>>>>cx25840 2-0044: Configured audio standard: automatic detection >>>>>cx25840 2-0044: Configured audio system: automatic standard and >>>>>mode detection >>>>>cx25840 2-0044: Specified standard: PAL-BDGHI >>>>>cx25840 2-0044: Specified input: Tuner >>>>>cx25840 2-0044: Specified audio input: Tuner >>>>>cx25840 2-0044: Specified audioclock freq: 48 kHz >>>>>cx25840 2-0044: Preferred audio mode: stereo >>>>>cx25840 2-0044: Selected 65 MHz format: autodetect >>>>>cx25840 2-0044: Selected 45 MHz format: chroma >>>>>wm8775 2-001b: Input: default >>>>>tda9887 2-0043: Data bytes: b=d4 c=70 e=09 >>>>>ivtv2: ================== END STATUS CARD #2 ================== >>>>> >>>>>Video and sound is perfect with 'cat /dev/video2 >test.mpg' and >>>>>mplayer - but mythtv chokes after 2 sec, claiming there is a >>>>>problem >>>> >>>>I'm confused. Do you mean it now works? Based on the log status I'd >>>>say it is working. There should be tuner debug messages in the log >>>>too, please post those too. >>>> >>>> Hans >>> >>>Although it is working with cat /dev/videoX >test.mpg after forcing >>>the channel - it is not working in mythtv (for more than 2 sec - the >>>video is fine for those two sec) >>> >>>Could it be that mythtv tries to interact with something moved or >>>renamed ? >> >> >>Probably. It's definitely a MythTV problem. Which MythTV version are you >>using? > > > Oh, I bet I know what this is. The input numbering changed for the > 150/500 cards. "Tuner 0" = 0 instead of 6, for instance. So that will > need to be reconfigured in MythTV. I had completely forgotten about > this myself.
Is this something I can set in the database (through setup) - or is it hardcoded? Sigurd _______________________________________________ ivtv-devel mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-devel
