On Monday 10 July 2006 19:40, Kenneth Hester wrote:
> The hardware seems to work under Windows 2k with Sage trial version.
> I can record 2 shows at once.
Can you upgrade to gcc-4.1.1 and recompile the driver?
> What does the message mean that says Encoder/Decode Mailbox not
> found? Is that some hardware probe that doesn't work or is it some
> software piece that is not right?
The firmware is loaded to the card and then the driver tries to find a
so-called mailbox (read: a magic memory value). These messages mean
that it cannot find it. In the past it was related to 64-bit errors,
but that's eliminated, and there are some indications that it may be a
gcc-4.1 code generation issue (hence the request to upgrade to 4.1.1).
Hans
>
> Thanks,
>
> Kenneth
>
> -----Original Message-----
> From: [EMAIL PROTECTED]
> [mailto:[EMAIL PROTECTED] Behalf Of Hans Verkuil
> Sent: Saturday, July 01, 2006 4:16 PM
> To: Discussion list for development of the IVTV driver
> Subject: Re: [ivtv-devel] [UNKNOWN CARD] PVR 500 MCE
>
> On Thursday 29 June 2006 23:32, Kenneth Hester wrote:
> > I have a new card that is not recognized. In addition there is
> > other odd behavior. On both the first and second card, the driver
> > reports that it is the second unit of a PVR 500.
> >
> > I can't get the card to work. I am running SUSE 10.1 with
> > ivtv-0.6.3 compiled with (raise the flag please) gcc 4.1.0-25 and
> > the suse built 2.6.16.13-default kernel. I added the ID to the
> > ivtv_pci_pvr150[] list and that makes the unknown card message go
> > away but it still doesn't work.
> >
> > Does the card need to be added somewhere else also or do other
> > changes need to be made?
> >
> > Right now only one card works at all. It has complete static on
> > lower channels but only slight static on upper channels. Audio is
> > good on all channels and it seems to tune to the correct
> > frequencies for us-cable.
> >
> > What problems does compiling with gcc 3.x solve? Do I have to
> > recompile the kernel with gcc 3.x if I recompile ivtv with gcc 3.x?
> >
> > Any ideas or solutions would be greatly appreciated.
>
> Can you verify in a Windows PC that the second tuner is really
> working? It could be broken hardware.
>
> Also make sure you are using gcc-4.1.1. I've seen rumors that 4.1 has
> bugs causing problems with this driver.
>
> Thanks,
>
> Hans
>
> > Thanks
> >
> > dmesg output:
> > ivtv: ==================== START INIT IVTV ====================
> > ivtv: version 0.6.3 (tagged release) loading
> > ivtv: Linux version: 2.6.16.13-4-default 586 REGPARM gcc-4.1
> > ivtv: In case of problems please include the debug info between
> > ivtv: the START INIT IVTV and END INIT IVTV lines, along with
> > ivtv: any module options, when mailing the ivtv-users mailinglist.
> > ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based)
> > tveeprom 0-0050: Hauppauge model 23552, rev D487, serial# 9525425
> > tveeprom 0-0050: tuner model is Samsung TCPN 2121P30A (idx 87, type
> > 70) tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08)
> > tveeprom 0-0050: second tuner model is Philips TEA5768HL FM Radio
> > (idx 101, type 62)
> > tveeprom 0-0050: audio processor is CX25843 (idx 37)
> > tveeprom 0-0050: decoder processor is CX25843 (idx 30)
> > tveeprom 0-0050: has radio, has no IR remote
> > ivtv0: This is the second unit of a PVR500
> > ivtv0: Correcting tveeprom data: no radio present on second unit
> > usb 1-1: new full speed USB device using uhci_hcd and address 2
> > tuner 0-0060: TEA5767 detected.
> > tuner 0-0060: chip found @ 0xc0 (ivtv i2c driver #0)
> > tuner 0-0060: type set to 62 (Philips TEA5767HN FM Radio)
> > tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0)
> > usb 1-1: new device found, idVendor=0609, idProduct=031d
> > usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=3
> > usb 1-1: Product: eHome Infrared Transceiver
> > usb 1-1: Manufacturer: SMK
> > usb 1-1: SerialNumber: SM0059g4
> > usb 1-1: configuration #1 chosen from 1 choice
> > cx25840 0-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
> > i8xx TCO timer: initialized (0x1060). heartbeat=30 sec (nowayout=0)
> > Linux agpgart interface v0.101 (c) Dave Jones
> > agpgart: Detected an Intel i810 Chipset.
> > agpgart: AGP aperture is 64M @ 0xf0000000
> > JBD: barrier-based sync failed on hda3 - disabling barriers
> > cx25840 0-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
> > lirc_dev: module not supported by Novell, setting U taint flag.
> > lirc_dev: IR Remote Control driver registered, at major 61
> > wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0)
> > lirc_mceusb2: module not supported by Novell, setting U taint flag.
> >
> > lirc_mceusb2: USB remote driver for LIRC v0.22
> > lirc_mceusb2: Martin Blatter <[EMAIL PROTECTED]>
> > usb 1-1: reset full speed USB device using uhci_hcd and address 2
> > lirc_dev: lirc_register_plugin: sample_rate: 0
> > lirc_mceusb2[2]: SMK eHome Infrared Transceiver on usb1:2
> > usbcore: registered new driver lirc_mceusb2
> > ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
> > ivtv0: Encoder revision: 0x02050032
> > ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers
> > (4096KB total) ivtv0: Allocate DMA encoder YUV stream: 194 x 10800
> > buffers (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 120
> > x 17472 buffers (2048KB total) ivtv0: Allocate DMA encoder PCM
> > audio stream: 455 x 4608 buffers (2048KB total)
> > tuner 0-0061: type set to 70 (Samsung TCPN 2121P30A)
> > ivtv0: Initialized WinTV PVR 500 (unit #2), card #0
> > ivtv: ====================== NEXT CARD ======================
> > ivtv1: Unknown card: vendor/device: 4444/0016
> > ivtv1: subsystem vendor/device: 0070/b7f7
> > ivtv1: cx23416 based
> > ivtv1: Defaulting to Hauppauge WinTV PVR-150 card
> > ivtv1: Please mail the vendor/device and subsystem vendor/device
> > IDs and what kind of
> > ivtv1: card you have to the ivtv-devel mailinglist
> > (www.ivtvdriver.org) ivtv1: Prefix your subject line with [UNKNOWN
> > CARD].
> > tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #1)
> > cx25840 1-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #1)
> > cx25840 1-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
> > wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #1)
> > tveeprom 1-0050: Hauppauge model 23552, rev D487, serial# 9525425
> > tveeprom 1-0050: tuner model is Samsung TCPN 2121P30A (idx 87, type
> > 70) tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08)
> > tveeprom 1-0050: second tuner model is Philips TEA5768HL FM Radio
> > (idx 101, type 62)
> > tveeprom 1-0050: audio processor is CX25843 (idx 37)
> > tveeprom 1-0050: decoder processor is CX25843 (idx 30)
> > tveeprom 1-0050: has radio, has no IR remote
> > ivtv1: This is the second unit of a PVR500
> > ivtv1: Correcting tveeprom data: no radio present on second unit
> > ivtv1: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
> > ivtv1 warning: Encoder mailbox not found
> > ivtv1 warning: Decoder mailbox not found
> > ivtv1: Error locating firmware.
> > ivtv1: Error -12 on initialization
> > ivtv: probe of 0000:02:09.0 failed with error -12
> > ivtv: ==================== END INIT IVTV ====================
> >
> >
> > _______________________________________________
> > ivtv-devel mailing list
> > [email protected]
> > http://ivtvdriver.org/mailman/listinfo/ivtv-devel
>
> _______________________________________________
> ivtv-devel mailing list
> [email protected]
> http://ivtvdriver.org/mailman/listinfo/ivtv-devel
>
>
> _______________________________________________
> ivtv-devel mailing list
> [email protected]
> http://ivtvdriver.org/mailman/listinfo/ivtv-devel
_______________________________________________
ivtv-devel mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-devel
