This card is supported since ivtv-0.6. You need kernel 2.6.16 or up for
this to work since the tuner (yes, it really has a tuner) isn't
supported in ivtv-0.4.6 or older (and that's not going to happen
either).
Hans
On Sunday 27 August 2006 06:36, Brian Litzinger wrote:
> Hi all,
>
> This is a YUAN Mini-PCI card based on the cx23416 chipset.
>
> It mostly works. Over the years I've been patching the various
> releases to make the card work correctly, but figure I'll go
> through official channels.
>
> So follows the log. The i2c errors don't bother anything.
> The board does not have a tuner. Just Composite and S-Video.
>
> Every once in a while I re-figure out the magic register
> bits to get the composite and S-Video bits correctly selected.
>
> If you make a space for this card, or perhaps support was
> added in post 0.4.6, I'll send along the bits for proper
> video mode selection.
>
> '-p 2' (I think) properly selects S-Video, or was it Composite?
> Well I had color PAL working awhile ago.
>
> --
> brian
>
>
> ivtv: ==================== START INIT IVTV ====================
> ivtv: version 0.4.6 (tagged release) loading
> ivtv: Linux version: 2.6.11-rc1 PENTIUMM gcc-3.3
> ivtv: In case of problems please include the debug info between
> ivtv: the START INIT IVTV and END INIT IVTV lines, along with
> ivtv: any module options, when mailing the ivtv-users mailinglist.
> ivtv0: Unknown card: vendor/device: 4444/0016
> ivtv0: subsystem vendor/device: ff01/d998
> ivtv0: cx23416 based
> ivtv0: Defaulting to WinTV PVR 150 card
> ivtv0: Please mail the vendor/device and subsystem vendor/device IDs
> and what ki nd of
> ivtv0: card you have to the ivtv-devel mailinglist
> (www.ivtvdriver.org) ivtv0: Prefix your subject line with [UNKNOWN
> CARD].
> ACPI: PCI interrupt 0000:00:14.0[A] -> GSI 12 (level, low) -> IRQ 12
> ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
> ivtv0 warning: i2c client addr: 0x50 not found for command 0x0!
> ivtv0: Error -19 reading Hauppauge eeprom.
> ivtv0: Possible causes: the tveeprom module was not loaded, or
> ivtv0: the eeprom kernel module was loaded before the tveeprom
> module. cx25840 0-0044: ivtv driver
> cx25840 0-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
> cx25840 0-0044: loaded /lib/modules/v4l-cx25840.fw firmware (13883
> bytes) ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44]
> ivtv0: loaded /lib/modules/v4l-cx2341x-enc.fw firmware (262144 bytes)
> ivtv0: Encoder revision: 0x02040011
> ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB
> total) ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers
> (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 120 x 17472
> buffers (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream:
> 455 x 4608 buffers (2048KB total) ivtv0 warning: i2c client addr:
> 0x1b not found for command 0x40046d11! ivtv0 warning: i2c client
> addr: 0x00 not found for command 0x40085618! ivtv0 warning: i2c
> client addr: 0x00 not found for command 0x402c5639! ivtv0 warning:
> i2c client addr: 0x1b not found for command 0x402c5639! ivtv0:
> Initialized WinTV PVR 150, card #0
> ivtv: ==================== END INIT IVTV ====================
> ivtv0 warning: i2c client addr: 0x1b not found for command
> 0x40046d11! ivtv0 warning: i2c client addr: 0x1b not found for
> command 0x40046d11! ivtv0 warning: i2c client addr: 0x1b not found
> for command 0x40046d11! ivtv0 warning: i2c client addr: 0x1b not
> found for command 0x40046d11! ivtv0 warning: i2c client addr: 0x1b
> not found for command 0x40046d11! ivtv0 warning: i2c client addr:
> 0x1b not found for command 0x40046d11! ivtv0 warning: i2c client
> addr: 0x1b not found for command 0x40046d11! ivtv0 warning: i2c
> client addr: 0x1b not found for command 0x40046d11! ivtv0 warning:
> i2c client addr: 0x1b not found for command 0x40046d11!
_______________________________________________
ivtv-devel mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-devel
