Hi, I have a new Winttv pvr 150, model 26552 rev F0A3 (as read off the card itself). When detected through ivtv 0.7.0, it lists correctly but almost seems to be the wrong configuration, as initialization commands give errors.
Here's the ivtv dmesg log: ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.7.0 (tagged release) loading ivtv: Linux version: 2.6.17-chw-8 SMP preempt mod_unload 586 gcc-3.4 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based) tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0) tda9887 0-0043: chip found @ 0x86 (ivtv i2c driver #0) wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0) tveeprom 0-0050: Hauppauge model 26552, rev F0A3, serial# 9499727 tveeprom 0-0050: tuner model is TCL MFNM05-4 (idx 103, type 43) tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08) tveeprom 0-0050: audio processor is CX25843 (idx 37) tveeprom 0-0050: decoder processor is CX25843 (idx 30) tveeprom 0-0050: has radio, has no IR remote ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv0: Encoder revision: 0x02050032 ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) ivtv0: Create encoder radio stream tuner 0-0061: type set to 43 (Philips NTSC MK3 (FM1236MK3 or FM1236/F)) ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c! ivtv0: i2c addr 0x44 not found for command 0x4008646f! ivtv0: i2c hardware 0x00000001 not found for command 0x4008646d! ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c! ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c! ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c! ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 ivtv: ==================== END INIT IVTV ==================== ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c! ivtv0: i2c addr 0x44 not found for command 0x4008646f! ivtv0: i2c hardware 0x00000001 not found for command 0x4008646d! ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c! ivtv0: i2c addr 0x44 not found for command 0xc0445624! ivtv0: i2c addr 0x44 not found for command 0xc0445624! ivtv0: i2c addr 0x44 not found for command 0xc0445624! ivtv0: i2c addr 0x44 not found for command 0xc0445624! I have a different pvr-150 of a differnt model that does work correctly in the system, so I believe the other components are ok. I have also attempted to force ivtv to tuner mode 50 with no improvement. I've been asking for help on some mythtv forums, and a moderator suggested I post the errors here. Thank you in advance for any information you can provide. -- Mike _______________________________________________ ivtv-devel mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-devel
