* Hans Verkuil <[EMAIL PROTECTED]> [2006-12-02 20:21]: > On Saturday 02 December 2006 20:55, Nuno Oliveira wrote: > > Hey, > > > > Similarly to what Martin Dauskardt ([EMAIL PROTECTED]) reported on Nov 19, > > I also get a lot of these errors > > > > ivtv0: i2c addr 0x21 not found for command 0xc0445624! > > last message repeated 3 times > > > > with a PVR-350 board, using 2.6.19 and ivtv-0.9.0. I can't get the > > card to work with these versions, although it works perfectly with > > 2.6.18 and ivtv-0.8.0. > > > > The kernel startup log follows. In the init phase there are already a > > number of these errors. Any ideas? > > Please add the following to the /etc/modprobe.conf file and try again: > > options saa7115 debug=1 > > Post the same log again, it should now contain some saa7115 debugging. > > Thanks, > > Hans
Hans, Thanks for the help. With 0.9.0, I don't get a saa7115 module installed. I presume you mean 'saa717x', which is what I got. Anyway, I added both lines to /etc/modprobe.conf: options saa7115 debug=1 options saa717x debug=1 Starting with an empty kernel, I did: modprobe -v saa717x modprobe -v ivtv This is the result I got from dmesg: ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.9.0 (tagged release) loading ivtv: Linux version: 2.6.19 SMP preempt mod_unload PENTIUM4 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected Hauppauge card (cx23415 based) ACPI: PCI Interrupt 0000:01:0b.0[A] -> GSI 22 (level, low) -> IRQ 22 ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes) input: i2c IR (Hauppauge) as /class/input/input6 ir-kbd-i2c: i2c IR (Hauppauge) detected at i2c-3/3-0018/ir0 [ivtv i2c driver #0] i2c_adapter i2c-3: Client creation failed at 0x40 (-5) msp3400 3-0040: MSP4418G-B3 found @ 0x80 (ivtv i2c driver #0) msp3400 3-0040: MSP4418G-B3 supports nicam and radio, mode is autodetect and autoselect i2c_adapter i2c-3: Client creation failed at 0x44 (-1) tuner 3-0043: chip found @ 0x86 (ivtv i2c driver #0) tda9887 3-0043: tda988[5/6/7] found @ 0x43 (tuner) tuner 3-0061: chip found @ 0xc2 (ivtv i2c driver #0) saa717x 3-0021: saa717x not found (id=01) saa717x 3-0021: saa717x not found (id=01) tveeprom 3-0050: Hauppauge model 48139, rev K257, serial# 2979907 tveeprom 3-0050: tuner model is Philips FM1216 ME MK3 (idx 57, type 38) tveeprom 3-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) (eeprom 0x74) tveeprom 3-0050: audio processor is MSP4418 (idx 25) tveeprom 3-0050: decoder processor is SAA7115 (idx 19) tveeprom 3-0050: has radio, has IR remote ivtv0: Autodetected Hauppauge WinTV PVR-350 ivtv0: Encoder revision: 0x02050032 ivtv0: Decoder revision: 0x02020023 ivtv0: Registered device video0 for encoder MPEG ivtv0: Registered device video32 for encoder YUV ivtv0: Registered device vbi0 for encoder VBI ivtv0: Registered device video24 for encoder PCM audio ivtv0: Registered device radio0 for encoder radio ivtv0: Registered device video16 for decoder MPEG ivtv0: Registered device vbi8 for decoder VBI ivtv0: Registered device vbi16 for decoder VOUT ivtv0: Registered device video48 for decoder YUV ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 bytes) tuner 3-0061: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3)) ivtv0: i2c addr 0x21 not found for command 0x4008646f! ivtv0: Initialized Hauppauge WinTV PVR-350, card #0 ivtv: ==================== END INIT IVTV ==================== A problem with saa717x detection? Thanks again, Nuno. _______________________________________________ ivtv-devel mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-devel
