Hello, I have a problem with Secam standard on my PVR 350 cards. Picture is ok but i don't have any sound. I know that the format i am receiving is Secam G and i know that PVR 350 works ok with secam L. Diference in these two scams is SOund Carrier (Secam G = 5.5MHz , Secam L = 6.5MHz).
I am using ivtv driver 0.4.6 with kernel 2.6.12. I can't use kernels 2.6.16 and higher becouse i am using VLC to stream channels on my STB. And VLC doesn't have V4L2 module for now. IVTV detect log: [4433624.327000] ivtv: ==================== START INIT IVTV ==================== [4433624.327000] ivtv: version 0.4.6 (tagged release) loading [4433624.327000] ivtv: Linux version: 2.6.15.7-ubuntu1-iskratel 686 gcc-4.0 [4433624.327000] ivtv: In case of problems please include the debug info between [4433624.327000] ivtv: the START INIT IVTV and END INIT IVTV lines, along with [4433624.327000] ivtv: any module options, when mailing the ivtv-users mailinglist. [4433624.332000] ivtv0: Autodetected WinTV PVR 350 card (cx23415 based) [4433624.333000] ACPI: PCI Interrupt 0000:01:03.0[A] -> GSI 16 (level, low) -> IRQ 17 [4433624.333000] ivtv0: Unreasonably low latency timer, setting to 64 (was 16) [4433624.389000] tveeprom: ivtv version [4433624.389000] tveeprom: Hauppauge: model = 48139, rev = K2B7, serial# = 8612420 [4433624.389000] tveeprom: tuner = Philips FM1216ME MK5 (idx = 117, type = 4) [4433624.389000] tveeprom: tuner fmt = PAL(B/G) PAL(I) SECAM(L/L') PAL(D/K) (eeprom = 0x74, v4l2 = 0x00400e17) [4433624.389000] tveeprom: audio processor = MSP4418 (type = 19) [4433624.389000] tveeprom: decoder processor = SAA7115 (type = 13) [4433624.389000] ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50] [4433624.410000] tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 [4433624.410000] ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61] [4433624.615000] saa7115 2-0021: ivtv driver [4433624.615000] saa7115 2-0021: saa7115 found @ 0x42 (ivtv i2c driver #0) [4433624.779000] ivtv0: i2c attach to card #0 ok [client=saa7115, addr=21] [4433624.843000] saa7127 2-0044: ivtv driver [4433624.846000] saa7127 2-0044: saa7129 found @ 0x88 (ivtv i2c driver #0) [4433624.849000] ivtv0: i2c attach to card #0 ok [client=saa7127, addr=44] [4433624.871000] msp3400 2-0040: ivtv driver [4433624.871000] msp3400 2-0040: chip=MSP4418G-B3 +nicam +simple +simpler +radio mode=simpler [4433624.878000] ivtv0: i2c attach to card #0 ok [client=MSP4418G-B3, addr=40] [4433624.878000] msp3400 2-0040: msp34xxg daemon started [4433624.897000] tda9887 2-0043: (ivtv) chip found @ 0x86 (ivtv i2c driver #0) [4433624.897000] ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43] [4433625.332000] ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) [4433625.443000] ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes) [4433625.499000] ivtv0: Encoder revision: 0x02050032 [4433625.501000] ivtv0: Decoder revision: 0x02020023 [4433625.502000] ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) [4433625.503000] ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total) [4433625.505000] ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total) [4433625.506000] ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) [4433625.508000] ivtv0: Create encoder radio stream [4433625.509000] ivtv0: Allocate DMA decoder MPEG stream: 16 x 65536 buffers (1024KB total) [4433625.510000] ivtv0: Allocate DMA decoder VBI stream: 512 x 2048 buffers (1024KB total) [4433625.511000] ivtv0: Create decoder VOUT stream [4433625.513000] ivtv0: Allocate DMA decoder YUV stream: 20 x 51840 buffers (1024KB total) [4433625.606000] ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 bytes) [4433625.633000] tuner: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3)) by ivtv i2c driver #0 [4433625.823000] ivtv0: Initialized WinTV PVR 350, card #0 ivtvctl -d /dev/video0 -I --log-status SAA7115 reg[STATUS#1 - 0x1E] = 83 Color Standard (D0-D1): SECAM White peak loop (D2): Not activated Gain value for act.lum. (min) (D3): Not limited Gain value for act.lum. (max) (D4): Not limited WIPA-mode slow-time constant (D5): Not activated Horizontal frequency (D6): Locked Field length (D7): Standard SAA7115 reg[STATUS#2 - 0x1F] = 91 Ready for capture (D0): Yes Macrovision 7.01 (D1): No MV Colorstripe burst (D2): No MV Colorstripe burst type 3 (D3): No Input signal timebase (D4): Stable (broadcast/DVD) Field frequency (D5): 50Hz H & V loops (D6): Locked Interlace (D7): Detected ioctl VIDIOC_LOG_STATUS ok [4306273.339000] ivtv0: ================= START STATUS CARD #0 ================= [4306273.339000] saa7115 0-0021: Audio frequency: 48 kHz [4306273.341000] saa7115 0-0021: Video signal: broadcast/DVD [4306273.341000] saa7115 0-0021: Frequency: 50Hz [4306273.341000] saa7115 0-0021: Detected format: SECAM [4306273.341000] saa7127 0-0044: Standard: 50 Hz [4306273.341000] saa7127 0-0044: Input: normal [4306273.341000] saa7127 0-0044: Output: S-Video + Composite [4306273.341000] saa7127 0-0044: WSS: disabled [4306273.341000] saa7127 0-0044: VPS: disabled [4306273.341000] saa7127 0-0044: CC: disabled [4306273.341000] tda9887 0-0043: Data bytes: b=94 c=70 e=09 [4306273.341000] ivtv0: ================== END STATUS CARD #0 ================== If someone know solution for this please help me? Thanks, Gregor Fuis _______________________________________________ ivtv-devel mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-devel
