Hi Jeremy, I think I am having the same problem as you. I am running the same kernel/distro.
I believe the correct firmware directory for this distro/kernel is /lib/firmware/2.6.22-14-generic. If you run the 'make unload' command then reload the cx18 module like this: modprobe cx18 debug=511 you will get more output in dmesg. If you look in the dmesg for the tveeprom messages, what model of card does it show? Mine is "Hauppauge model 74041, rev C5B2." There are several different versions of the HVR-1600 (74021, 74041). Maybe that is a factor? For anyone reading here are the full logs of loading the module and attempting to open video0: ### Loading module ### [ 5557.118919] Linux video capture interface: v2.00 [ 5557.140555] cx18: Start initialization, version 0.1.0 [ 5557.140645] cx18-0: Initializing card #0 [ 5557.140652] cx18-0: Autodetected Hauppauge card [ 5557.140657] cx18-0 info: base addr: 0xf8000000 [ 5557.140660] cx18-0 info: Enabling pci device [ 5557.140688] ACPI: PCI Interrupt 0000:02:02.0[A] -> GSI 17 (level, low) -> IRQ 22 [ 5557.140709] cx18-0 info: cx23418 (rev 0) at 02:02.0, irq: 22, latency: 64, memory: 0xf8000000 [ 5557.140714] cx18-0 info: attempting ioremap at 0xf8000000 len 0x04000000 [ 5557.140916] cx18-0: cx23418 revision 01010000 (B) [ 5557.213547] cx18-0 info: GPIO initial dir: 0000cffe out: 00003001 [ 5557.213554] cx18-0 info: activating i2c... [ 5557.213559] cx18-0 i2c: i2c init [ 5557.251500] cx18-0 info: Active card count: 1. [ 5557.305690] tveeprom 0-0050: Hauppauge model 74041, rev C5B2, serial# 2558553 [ 5557.305698] tveeprom 0-0050: MAC address is 00-0D-FE-27-0A-59 [ 5557.305705] tveeprom 0-0050: tuner model is TCL M2523_5N_E (idx 112, type 50) [ 5557.305709] tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08) [ 5557.305713] tveeprom 0-0050: audio processor is CX23418 (idx 38) [ 5557.305717] tveeprom 0-0050: decoder processor is CX23418 (idx 31) [ 5557.305723] tveeprom 0-0050: has no radio, has IR receiver, has IR transmitter [ 5557.305736] cx18-0: Autodetected Hauppauge HVR-1600 [ 5557.305748] cx18-0 info: NTSC tuner detected [ 5557.334386] cx18-0 info: Loaded module tuner [ 5557.346389] cx18-0 info: Loaded module cs5345 [ 5557.346397] cx18-0 i2c: i2c client register [ 5557.348649] tuner 1-0061: chip found @ 0xc2 (cx18 i2c driver #0-1) [ 5557.348662] cx18-0 i2c: i2c client register [ 5557.349444] cs5345 0-004c: chip found @ 0x98 (cx18 i2c driver #0-0) [ 5557.351968] cx18-0 info: Allocate encoder MPEG stream: 64 x 32768 buffers (2048kB total) [ 5557.352450] cx18-0 info: Allocate TS stream: 64 x 32768 buffers (2048kB total) [ 5557.352615] cx18-0 info: Allocate encoder YUV stream: 16 x 131072 buffers (2048kB total) [ 5557.352656] cx18-0 info: Allocate encoder PCM audio stream: 227 x 4608 buffers (1021kB total) [ 5557.352939] cx18-0: Disabled encoder IDX device [ 5557.353000] cx18-0: Registered device video0 for encoder MPEG (2 MB) [ 5557.353034] cx18-0: Registered device video16 for TS (2 MB) [ 5557.353069] cx18-0: Registered device video32 for encoder YUV (2 MB) [ 5557.353104] cx18-0: Registered device vbi0 for encoder VBI (1 MB) [ 5557.353136] cx18-0: Registered device video24 for encoder PCM audio (1 MB) [ 5557.353148] tuner-simple 1-0061: type set to 50 (TCL 2002N) [ 5557.354347] cx18-0: Initialized card #0: Hauppauge HVR-1600 [ 5557.354368] cx18: End initialization ### Open video0 (via v4l2-ctl --all) ### [ 5572.822636] cx18-0 info: load segment a00000-a07fff [ 5572.832039] cx18-0 info: load segment ae0000-ae00ff [ 5572.832118] cx18-0 info: load segment b00000-b1a65f [ 5572.868447] cx18-0: loaded v4l-cx23418-apu.fw firmware V00120000 (141200 bytes) [ 5572.883482] cx18-0: Mismatch at offset 0 [ 5572.883520] cx18-0: Retry loading firmware [ 5572.901262] cx18-0 info: load segment a00000-a07fff [ 5572.910920] cx18-0 info: load segment ae0000-ae00ff [ 5572.911004] cx18-0 info: load segment b00000-b1a65f [ 5572.947220] cx18-0: loaded v4l-cx23418-apu.fw firmware V00120000 (141200 bytes) [ 5572.955623] cx18-0: Mismatch at offset 0 [ 5572.955659] cx18-0: Failed to initialize on minor 0 -Andrew On Dec 29, 2007 7:56 PM, Jeremy A. Hudnall <[EMAIL PROTECTED]> wrote: > Hi, > I am having some problems getting this HVR 1600 working with the new > beta drivers. First let me get some info for you. > > Kernel version: 2.6.22-14-generic > Distro: Ubuntu Gutsy 7.10 > > Here is some commands I have ran trying to see what is going on. > > [EMAIL PROTECTED]:~$ cat /dev/video16 > tst.mpg > cat: /dev/video16: No such device or address > > [EMAIL PROTECTED]:~$ cat /dev/video0 > tst.mpg > cat: /dev/video0: No such device or address > > [EMAIL PROTECTED] :~$ lspci | grep video > > 03:02.0 Multimedia video controller: Conexant CX23418 Single-Chip MPEG-2 > Encoder with Integrated Analog Video/Broadcast Audio Decoder > > [EMAIL PROTECTED]:~$ modprobe -v cx18 > > I think it is odd that the above modprobe does not output anything. Is > it supposed to print something? > > [EMAIL PROTECTED] :~$ dmesg | grep cx18 > [ 52.705719] cx18: Start initialization, version 0.1.0 > [ 52.705794] cx18-0: Initializing card #0 > [ 52.705799] cx18-0: Autodetected Hauppauge card > [ 52.706086] cx18-0: cx23418 revision 01010000 (B) > [ 52.856064] cx18-0: Autodetected Hauppauge HVR-1600 > [ 53.028634] tuner 1-0061: chip found @ 0xc2 (cx18 i2c driver #0-1) > [ 53.028684] cs5345 0-004c: chip found @ 0x98 (cx18 i2c driver #0-0) > [ 53.031479 ] cx18-0: Disabled encoder IDX device > [ 53.031540] cx18-0: Registered device video0 for encoder MPEG (2 MB) > [ 53.031574] cx18-0: Registered device video16 for TS (2 MB) > [ 53.031607] cx18-0: Registered device video32 for encoder YUV (2 MB) > [ 53.031646] cx18-0: Registered device vbi0 for encoder VBI (1 MB) > [ 53.031681] cx18-0: Registered device video24 for encoder PCM audio > (1 MB) > [ 53.032891] cx18-0: Initialized card #0: Hauppauge HVR-1600 > [ 53.032925] cx18: End initialization > [ 176.054655] cx18-0: Mismatch at offset 8130 > [ 176.054699] cx18-0: Retry loading firmware > [ 176.092942] cx18-0: Mismatch at offset 8130 > [ 176.093003] cx18-0: Failed to initialize on minor 0 > [ 178.322270] cx18-0: Failed to initialize on minor 0 > [ 331.134016] cx18-0: Failed to initialize on minor 0 > [ 399.633871] cx18-0: Failed to initialize on minor 0 > [ 772.030026] cx18-0: Failed to initialize on minor 0 > [ 849.635194] cx18-0: Failed to initialize on minor 32 > [ 885.339320] cx18-0: Failed to initialize on minor 0 > [ 901.762636] cx18-0: Failed to initialize on minor 0 > [ 1631.775526] cx18-0: Failed to initialize on minor 0 > [ 1862.017339] cx18-0: Failed to initialize on minor 16 > [ 2949.709601] cx18-0: Failed to initialize on minor 16 > [ 2953.371977] cx18-0: Failed to initialize on minor 0 > [EMAIL PROTECTED]:~$ > > Also my agp nvidia 6800gs video card does not want to work with either > the nv or nvidia drivers now. I think this started after installing or > "messng" around with the cx18 drivers. > > I also put the windows haupuage firmware in the /lib/firmware directory > and renamed them as in the how to. I am not sure if this is the exact > location those are supposed to be or not. > > > regards, JEremy > > > > > _______________________________________________ > ivtv-devel mailing list > [email protected] > http://ivtvdriver.org/mailman/listinfo/ivtv-devel > _______________________________________________ ivtv-devel mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-devel
