On Mon, 2008-07-07 at 10:46 +0100, Brian Hope wrote: > Pin 0 seems to do the trick:
Good. I've committed the ".xceive_pin = 0" change to http://linuxtv.org/hg/~awalls/v4l-dvb and asked Mauro to pull the change into the master repository. Give it a few days. BTW, Do you still have problems with audio not working on some of your S-Video and Composite inputs? If you still are, I'm guessing the Yuan MPC718 might be using an audio set-up similar to the Conexant Raptor PAL/SECAM board. I can try fixing that up too, if you'd want to test the changes. I'm not sure what to do about digital video yet... Regards, Andy > [ 6441.751294] xc2028 1-0061: Loading 48 firmware images from > xc3028-v27.fw, type: xc2028 firmware, ver 2.7 > [ 6441.751406] cx18-0 info: Resetting tuner > [ 6441.755935] xc2028 1-0061: Loading firmware for type=BASE (1), id > 0000000000000000. > [ 6441.755947] cx18-0 info: Resetting tuner > [ 6443.415638] xc2028 1-0061: Loading firmware for type=(0), id > 000000000000b700. > [ 6443.597174] cx18-0 info: Mute > [ 6443.597181] cx18-0 info: v4l2 ioctl: set frequency 1076 > [ 6443.752939] cx18-0 info: Unmute > [ 6443.831611] cx18-0 info: Mute > [ 6443.831624] cx18-0 info: Resetting tuner > [ 6443.836816] xc2028 1-0061: Loading firmware for type=BASE FM (401), > id 0000000000000000. > [ 6443.836825] cx18-0 info: Resetting tuner > [ 6446.606830] xc2028 1-0061: Loading firmware for type=FM (400), id > 0000000000000000. > [ 6446.784395] cx18-0 info: decoder set video input 2, audio input 0 > [ 6446.784484] cx18-0 info: Unmute > [ 6446.787051] cx18-0 info: Mute > On Sun, 2008-07-06 at 12:41 -0400, Andy Walls wrote: > > On Sun, 2008-07-06 at 09:00 +0100, Brian Hope wrote: > > > Using the latest firmware and drivers the cards load but I get i2c > > > errors. Any suggestions? > > > > Since all the I2C errors are related to loading the XC3028 tuner > > firmware, we need to find the correct GPIO pin of the CX23418 to reset > > the XC3028 tuner. > > > > Quoting Hans' May 30th post to the list: > > > > > You need to find the correct .xceive_pin setting in the card definition. > > > Try values 10 and 12 first, then the remaining values in the range > > > 8-15, then the whole range from 1-31. [ed. 0-31] [...] > > > > > > It's tedious, but one of the 32 pins is used to reset the xceive tuner > > > so that it can load the firmware. > > > > We never received feedback, so I'm pretty sure the ".xceive_pin = 15" > > setting in cx18-cards.c for the Yuan MPC-718 is wrong. Please go > > through the tedium of iteratively changing the xceive_pin value and > > recompiling and retesting the driver to find the right number. > > > > > > Regards, > > Andy _______________________________________________ ivtv-devel mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-devel
