Thanks for responding Stephen,
It tells me:
FATAL: module tveeprom not found.
I installed ivtv from the atrpms through apt-get following the howto I mentioned in my first message.
I'm useing fedora core 3, mostly My backround is with SuSE so I'm kind of lost in fedora :/
Thanks again!
-Ben
Stephen Webb wrote:
What is the output of dmesg when you load tveeprom module?
AKA modprobe tveeprom && dmesg
On Sat, 2005-02-05 at 15:50 -0500, [EMAIL PROTECTED] wrote:
Greetings,
The fellow that runs http://www.wilsonet.com/mythtv/ suggested that if i have any troubles with my tuner that i send an email to this list and include:
Feb 5 14:12:31 localhost kernel: ivtv: ==================== START INIT IVTV ==================== Feb 5 14:12:31 localhost kernel: ivtv: version 0.2.0 (rc3e) loading Feb 5 14:12:31 localhost kernel: ivtv: Linux version: 2.6.9-1.724_FC3 686 REGPARM 4KSTACKS gcc-3.4 Feb 5 14:12:31 localhost kernel: ivtv: In case of problems please include the debug info Feb 5 14:12:31 localhost kernel: ivtv: between the START INIT IVTV and END INIT IVTV lines when Feb 5 14:12:31 localhost kernel: ivtv: mailing the ivtv-devel mailinglist. Feb 5 14:12:31 localhost kernel: ivtv: Autodetected WinTV PVR 250 card Feb 5 14:12:31 localhost kernel: ivtv: Found an iTVC15 based chip Feb 5 14:12:31 localhost kernel: ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 9 (level, low) -> IRQ 9 Feb 5 14:12:31 localhost kernel: ivtv: VIA PCI device: 0x0691 vendor: 0x1106 Feb 5 14:12:31 localhost kernel: ivtv: Failed to load module tveeprom Feb 5 14:12:31 localhost kernel: ivtv: i2c client addr: 0x50 not found! Feb 5 14:12:31 localhost kernel: ivtv: Error -19 reading Hauppauge eeprom. Feb 5 14:12:31 localhost kernel: ivtv: Possible causes: the tveeprom module was not loaded, or Feb 5 14:12:32 localhost kernel: ivtv: the eeprom kernel module was loaded before the tveeprom module. Feb 5 14:12:32 localhost kernel: tuner: Ignoring new-style parameters in presence of obsolete ones Feb 5 14:12:32 localhost kernel: tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 Feb 5 14:12:32 localhost kernel: ivtv: i2c attach [client=(tuner unset),ok] Feb 5 14:12:32 localhost kernel: saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005) Feb 5 14:12:32 localhost kernel: saa7115: detecting saa7115 client on address 0x42 Feb 5 14:12:32 localhost kernel: saa7115: writing init values Feb 5 14:12:32 localhost kernel: ivtv: i2c attach [client=saa7115[0],ok] Feb 5 14:12:32 localhost kernel: saa7115: status: (1E) 0x48, (1F) 0xc0 Feb 5 14:12:32 localhost kernel: msp3400: Ignoring new-style parameters in presence of obsolete ones Feb 5 14:12:32 localhost kernel: msp34xx: init: chip=MSP3445G-B8 +nicam +simple +radio Feb 5 14:12:32 localhost kernel: ivtv: i2c attach [client=MSP3445G-B8,ok] Feb 5 14:12:32 localhost kernel: msp3410: daemon started Feb 5 14:12:33 localhost kernel: ivtv: Encoder revision: 0x02040024 Feb 5 14:12:33 localhost kernel: ivtv: Encoder Firmware is buggy, use version 0x02040011 Feb 5 14:12:33 localhost kernel: ivtv: Decoder revision: 0x02020023 Feb 5 14:12:33 localhost kernel: ivtv: Configuring WinTV PVR 250 card with 4 streams Feb 5 14:12:33 localhost kernel: ivtv: Create DMA stream 0 using 256 16384 byte buffers 4194304 kbytes total Feb 5 14:12:33 localhost kernel: ivtv: Registered v4l2 device, streamtype 0 min Feb 5 14:12:33 localhost kernel: ivtv: Create DMA stream 1 Feb 5 14:12:33 localhost kernel: ivtv: Registered v4l2 device, streamtype 1 min Feb 5 14:12:33 localhost kernel: ivtv: Create stream 2 using 40 52224 byte buff Feb 5 14:12:33 localhost kernel: ivtv: Registered v4l2 device, streamtype 2 min Feb 5 14:12:33 localhost kernel: ivtv: Create DMA stream 3 using 455 4608 byte Feb 5 14:12:33 localhost kernel: ivtv: Registered v4l2 device, streamtype 3 min Feb 5 14:12:33 localhost kernel: ivtv: Could not detect tuner standard, default Feb 5 14:12:33 localhost kernel: tuner: tuner type not set Feb 5 14:12:33 localhost kernel: ivtv: Setting audio matrix to input 3, output Feb 5 14:12:33 localhost kernel: ivtv: Switching standard to NTSC. Feb 5 14:12:33 localhost kernel: tuner: tuner type not set Feb 5 14:12:33 localhost kernel: saa7115: decoder set norm NTSC Feb 5 14:12:33 localhost kernel: ivtv: ivtv_enc_thread: pid = 3544, itv = 0xd8c Feb 5 14:12:33 localhost kernel: saa7115: set audio: 0x01 Feb 5 14:12:33 localhost kernel: ivtv: Initialized WinTV PVR 250, card #0 Feb 5 14:12:33 localhost kernel: ivtv: ==================== END INIT IVTV ===
I'm just getting static when I try to capture from the card. Also I have to /sbin/depmod -a and /sbin/modprobe ivtv after every reboot, the modules won't take at boot time.
Any assistance you folks can provide is greatly appreciated! I did get this card working in WinXp with hauppauge's drivers as I bought it off ebay for extremely cheap and wanted to prove that the card did work and I was successfull at getting my cable channels there.
-Ben
------------------------------------------------------- This SF.Net email is sponsored by: IntelliVIEW -- Interactive Reporting Tool for open source databases. Create drag-&-drop reports. Save time by over 75%! Publish reports on the web. Export to DOC, XLS, RTF, etc. Download a FREE copy at http://www.intelliview.com/go/osdn_nl _______________________________________________ ivtv-devel mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/ivtv-devel
------------------------------------------------------- This SF.Net email is sponsored by: IntelliVIEW -- Interactive Reporting Tool for open source databases. Create drag-&-drop reports. Save time by over 75%! Publish reports on the web. Export to DOC, XLS, RTF, etc. Download a FREE copy at http://www.intelliview.com/go/osdn_nl _______________________________________________ ivtv-devel mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/ivtv-devel
