I took a look under the sticker to make sure the tuner is actually the one tveeprom reports.
It sais: FM1216ME/I H-3. Is this exactly the same as the Philips FM1216 ME MK3 being identified by tveeprom? /Mat ----- Original Message ----- From: "Raymond Scholz" <[EMAIL PROTECTED]> To: <[email protected]> Sent: Wednesday, March 16, 2005 10:02 AM Subject: [ivtv-devel] Re: PVR-350 Tuner problem I'm experiencing the same problem with my PVR350. Composite4 works, Tuner0 doesn't - only static :-/ Kernel 2.6.11.3 ivtv 0.3.2i (tried with latest 0.2 too) PAL country (Germany) Epia M10000 with Unichrome drivers+DRM � "MythTV user" <[EMAIL PROTECTED]> wrote: > I diffed our IVTV outputs (from when I had the 2.6.10 kernel and there's not > much difference. >< saa7115: status: (1E) 0x00, (1F) 0xc0 >--- >> saa7115: status: (1E) 0x40, (1F) 0xc0 Does this matter? I can observe the same output (0x40). Here is my output: ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.3.2 (i) loading ivtv: Linux version: 2.6.11.3 preempt VIAC3-2 gcc-3.3 ivtv: In case of problems please include the debug info ivtv: between the START INIT IVTV and END INIT IVTV lines when ivtv: mailing the ivtv-devel mailinglist. ivtv: Autodetected WinTV PVR 350 card ivtv: Found an iTVC15 based chip ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10 PCI: setting IRQ 10 as level-triggered ACPI: PCI interrupt 0000:00:14.0[A] -> GSI 10 (level, low) -> IRQ 10 ivtv: Unreasonably low latency timer, setting to 64 (was 32) ivtv: VIA PCI device: 0x3123 vendor: 0x1106 tveeprom: Hauppauge: model = 48139, rev = K157, serial# = 2944075 tveeprom: tuner = Philips FM1216 ME MK3 (idx = 57, type = 38) tveeprom: tuner fmt = PAL(D/K) (eeprom = 0x74, v4l2 = 0x00400e17) tveeprom: audio_processor = CS5331 (type = 9) ivtv: i2c attach [client=tveeprom[0],ok] ivtv: Tuner Type 38, Tuner formats 0x00400e17, Radio: yes, Model 0x00ad1557, Revision 0x00000001 ivtv: PAL tuner detected ivtv: SECAM tuner detected ivtv: Radio detected tuner: Ignoring new-style parameters in presence of obsolete ones tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 ivtv: i2c attach [client=(tuner unset),ok] saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005) saa7115: detecting saa7115 client on address 0x42 saa7115: writing init values ivtv: i2c attach [client=saa7115[0],ok] saa7115: status: (1E) 0x40, (1F) 0xc0 saa7127: Ignoring new-style parameters in presence of obsolete ones saa7127: video encoder driver version V 0.3 loaded saa7127: detecting saa7127 client on address 0x88 saa7127: Selecting NTSC video Standard saa7127: Selecting S-Video+Composite saa7127: Turn WSS off saa7127: Widescreen Mode 4:3 Full Format saa7127: Selecting Normal Encoder Input saa7127: Enable Video Output ivtv: i2c attach [client=saa7127[0],ok] msp34xx: ivtv version msp34xx: init: chip=MSP3418W-B3, has NICAM support, simple (D) mode, simpler (G) no-thread mode msp34xx: $Id$ compiled on: Mar 15 2005 00:23:30 ivtv: i2c attach [client=MSP3418W-B3,ok] ivtv: Encoder revision: 0x02040011 ivtv: Decoder revision: 0x02020023 ivtv: Configuring WinTV PVR 350 card with 10 streams ivtv: Create DMA stream 0 using 1024 16384 byte buffers 16777216 kbytes total ivtv: Registered v4l2 device, streamtype 0 minor 0 ivtv: Create DMA stream 1 ivtv: Registered v4l2 device, streamtype 1 minor 32 ivtv: Create stream 2 using 40 52224 byte buffers 2097152 kbytes total ivtv: Registered v4l2 device, streamtype 2 minor 224 ivtv: Create DMA stream 3 using 455 4608 byte buffers 2097152 kbytes total ivtv: Registered v4l2 device, streamtype 3 minor 24 ivtv: Create stream 4 ivtv: Registered v4l2 device, streamtype 4 minor 64 ivtv: Create DMA stream 5 using 16 65536 byte buffers 1048576 kbytes total ivtv: Registered v4l2 device, streamtype 5 minor 16 ivtv: Create stream 6 using 1024 2048 byte buffers 262144 kbytes total ivtv: Registered v4l2 device, streamtype 6 minor 228 ivtv: Create stream 7 ivtv: Registered v4l2 device, streamtype 7 minor 232 ivtv: Create DMA stream 8 using 6 86400 byte buffers 518400 kbytes total ivtv: Registered v4l2 device, streamtype 8 minor 48 ivtv: Create DMA stream 9 using 32 65536 byte buffers 2097152 kbytes total ivtv: Setting Tuner 38 tuner: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3)) by ivtv i2c driver #0 saa7115: decoder set input (4) saa7115: now setting Composite input ivtv: Setting audio matrix to input 3, output 1 ivtv: Switching standard to PAL. ivtv: ivtv_enc_thread: pid = 1522, itv = 0xde920320 ivtv: ivtv_dec_thread: pid = 1523, itv = 0xde920320 saa7115: decoder set norm PAL saa7115: set audio: 0x01 saa7127: Setting Encoder Video Standard saa7127: Set PAL Video Mode saa7127: Selecting PAL video Standard ivtv: Initialized WinTV PVR 350, card #0 ivtv: ==================== END INIT IVTV ==================== > I have noticed that tda9887 don't load automatically for me. I have tried > modprobing it myself but it doesn't seem to make any difference, but I do > get the 'tda9885/6/7: chip found @ 0x86' output if I do. Do you modprobe it > manually or it auto-loads by ivtv? Same for me in this case. Cheers, Ray (somewhat desperate :-) ------------------------------------------------------- SF email is sponsored by - The IT Product Guide Read honest & candid reviews on hundreds of IT Products from real users. Discover which products truly live up to the hype. Start reading now. http://ads.osdn.com/?ad_ide95&alloc_id396&op=ick _______________________________________________ ivtv-devel mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/ivtv-devel ------------------------------------------------------- SF email is sponsored by - The IT Product Guide Read honest & candid reviews on hundreds of IT Products from real users. Discover which products truly live up to the hype. Start reading now. http://ads.osdn.com/?ad_id=6595&alloc_id=14396&op=click _______________________________________________ ivtv-devel mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/ivtv-devel
