Robert, Not sure about the lockup's but I know your not getting the correct modules loaded for your board. I had similar ivtv log output and always got static on every channel.
>tveeprom: The eeprom says no radio is present, but the tuner type >tveeprom: indicates otherwise. I will assume that radio is present. >tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 7805262 >tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57) >tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) >tveeprom: audio_processor = MSP3410D (type = 5) The no radio present is the key. I'm running FC3 using ATrpm's as per Jarod's guide.The tricky part is that there is module overlap between V4L2, IVTV and the base kernel. I think you need to install the IVTV last to make sure nothing get's overwritten. I was close to having it working before and the IVTV logs looked good except it was complaining about the radio on the 500 mce. Now that it's working that message is gone from the log. Bottom line is that I was loading either the wrong tveeprom or tuner module. It was close but not quite there. Here are the lines from my modprobe.conf # alias char-major-81 videodev alias char-major-81-0 ivtv alias char-major-81-1 ivtv alias char-major-81-2 bttv alias tveeprom tveeprom-ivtv alias tuner tuner-ivtv alias msp3400 msp3400-ivtv options cx25840 no_black_magic=1 # kernel-2.6.10-1.770_14.rhfc3.at video4linux-kmdl-2.6.10-1.770_14.rhfc3.at-20050310_100754-57.rhfc3.at ivtv-kmdl-2.6.10-1.770_14.rhfc3.at-0.3.2i-72.rhfc3.at bttv-kmdl-2.6.10-1.770_14.rhfc3.at-0.9.15_20050310_100754-57.rhfc3.at Attached are logs form my working 500mce config for both i & j... On Mon, 21 Mar 2005 20:13:28 -0600, Robert Del Huerto <[EMAIL PROTECTED]> wrote: > I downloaded the ivtv-0.3.2j source and configured my card as > instructed. When I do 'cat /dev/video0 > test.mpg' my computer would > reboot after about 10 seconds of video capture. > > Later, I installed the following from atrpms.net: > kernel-2.6.10-1.770_14.rhfc3.at > video4linux-kmdl-2.6.10-1.770_14.rhfc3.at-20050310_100754-57.rhfc3.at > ivtv-kmdl-2.6.10-1.770_14.rhfc3.at-0.3.2i-72.rhfc3.at > > ...and for a moment I thought the problem was gone. But, after about 3 > minutes of video capture my computer rebooted. This happened whether I > was running the capture from a command line (runlevel 3) or KDE. > > Any help will be greatly appreciated. > > My system is: > AMD Athlon 1800 > Biostar M7VIT motherboard > with a VIA VT8377 (KT400)/VT8235 chipset > and a Winbond W83697HF > NVidia FX video card > 1GB RAM > Hauppauge 500MCE > Fedora Core 3 > 480W Power Supply > > and my ivtv log is as follows:
ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.3.2 (i) loading ivtv: Linux version: 2.6.10-1.770_14.rhfc3.at 686 REGPARM gcc-3.4 ivtv: In case of problems please include the debug info ivtv: between the START INIT IVTV and END INIT IVTV lines when ivtv: mailing the ivtv-devel mailinglist. ivtv: Autodetected WinTV PVR 150 card ivtv: Found an iTVC16 based chip ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 5 ACPI: PCI interrupt 0000:02:08.0[A] -> GSI 5 (level, low) -> IRQ 5 ivtv: Unreasonably low latency timer, setting to 64 (was 32) ivtv: XXX PCI device: 0x01e0 vendor: 0x10de ivtv: i2c attach [client=tveeprom,ok] tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 ivtv: i2c attach [client=(tuner unset),ok] tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 7855605 tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57) tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) tveeprom: audio_processor = MSP3410D (type = 5) ivtv: Tuner Type 57, Tuner formats 0x00001000, Radio: yes, Model 0x00914652, Revision 0xdcc9cc28 ivtv: NTSC tuner detected ivtv: Radio detected cx25840: Ignoring new-style parameters in presence of obsolete ones cx25840: FW image '/lib/modules/HcwMakoA.ROM' of size 14264 loaded. cx25840: FW image md5 digest: 3a4803384f749d644ee1f1ca9dcb12fa cx25840: FW image sha1 digest: 2b5e6292b7391c980b93d156cf6b34178ce770f6 ivtv: i2c attach [client=cx25840[0],ok] wm8775: Ignoring new-style parameters in presence of obsolete ones wm8775: Setting register ADCFMT (7) to 1, R11.0..1, old value 02 wm8775: Setting register ADCMS (8) to 1, R12.8..8, old value 00 wm8775: Setting register DCY (24) to 8, R18.4..7, old value 03 wm8775: Setting register NGAT (27) to 1, R19.0..0, old value 00 wm8775: Setting register LRBOTH (30) to 1, R21.8..8, old value 00 wm8775: Setting register AMX (33) to 15, R21.0..3, old value 01 wm8775: Updating register 0 (R23), config: 2e01 active: 2e00. wm8775: Skipping register 1 (R7), config: 0e00 active: 0e00. wm8775: Updating register 2 (R11), config: 1622 active: 1621. wm8775: Updating register 3 (R12), config: 1802 active: 1902. wm8775: Skipping register 4 (R13), config: 1a00 active: 1a00. wm8775: Skipping register 5 (R14), config: 1ccf active: 1ccf. wm8775: Skipping register 6 (R15), config: 1ecf active: 1ecf. wm8775: Skipping register 7 (R16), config: 207b active: 207b. wm8775: Skipping register 8 (R17), config: 2200 active: 2200. wm8775: Updating register 9 (R18), config: 2432 active: 2482. wm8775: Updating register 10 (R19), config: 2600 active: 2601. wm8775: Skipping register 11 (R20), config: 2826 active: 2826. wm8775: Updating register 12 (R21), config: 2a01 active: 2b0f. ivtv: i2c attach [client=wm8775[0],ok] ivtv: Encoder revision: 0x02050032 ivtv: Encoder Firmware may be buggy, use version 0x02040011 ivtv: Configuring WinTV PVR 150 card with 5 streams ivtv: Create DMA stream 0 using 1024 16384 byte buffers 16777216 kbytes total ivtv: Registered v4l2 device, streamtype 0 minor 1 ivtv: Create DMA stream 1 ivtv: Registered v4l2 device, streamtype 1 minor 32 ivtv: Create stream 2 using 40 52224 byte buffers 2097152 kbytes total ivtv: Registered v4l2 device, streamtype 2 minor 225 ivtv: Create DMA stream 3 using 455 4608 byte buffers 2097152 kbytes total ivtv: Registered v4l2 device, streamtype 3 minor 24 ivtv: Create stream 4 ivtv: Registered v4l2 device, streamtype 4 minor 64 ivtv: Setting Tuner 57 tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #0 ivtv: Switching standard to NTSC. ivtv: Initialized WinTV PVR 150, card #0 ivtv: Autodetected WinTV PVR 150 card ivtv: Found an iTVC16 based chip ivtv: ivtv_enc_thread: pid = 4649, itv = 0xdcc91a20 ACPI: PCI interrupt 0000:02:09.0[A] -> GSI 12 (level, low) -> IRQ 12 ivtv: Unreasonably low latency timer, setting to 64 (was 32) ivtv: XXX PCI device: 0x01e0 vendor: 0x10de ivtv: i2c attach [client=tveeprom,ok] tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #1 ivtv: i2c attach [client=(tuner unset),ok] cx25840: FW image '/lib/modules/HcwMakoA.ROM' of size 14264 loaded. cx25840: FW image md5 digest: 3a4803384f749d644ee1f1ca9dcb12fa cx25840: FW image sha1 digest: 2b5e6292b7391c980b93d156cf6b34178ce770f6 ivtv: i2c attach [client=cx25840[1],ok] wm8775: Setting register ADCFMT (7) to 1, R11.0..1, old value 02 wm8775: Setting register ADCMS (8) to 1, R12.8..8, old value 00 wm8775: Setting register DCY (24) to 8, R18.4..7, old value 03 wm8775: Setting register NGAT (27) to 1, R19.0..0, old value 00 wm8775: Setting register LRBOTH (30) to 1, R21.8..8, old value 00 wm8775: Setting register AMX (33) to 15, R21.0..3, old value 01 wm8775: Updating register 0 (R23), config: 2e01 active: 2e00. wm8775: Skipping register 1 (R7), config: 0e00 active: 0e00. wm8775: Updating register 2 (R11), config: 1622 active: 1621. wm8775: Updating register 3 (R12), config: 1802 active: 1902. wm8775: Skipping register 4 (R13), config: 1a00 active: 1a00. wm8775: Skipping register 5 (R14), config: 1ccf active: 1ccf. wm8775: Skipping register 6 (R15), config: 1ecf active: 1ecf. wm8775: Skipping register 7 (R16), config: 207b active: 207b. wm8775: Skipping register 8 (R17), config: 2200 active: 2200. wm8775: Updating register 9 (R18), config: 2432 active: 2482. wm8775: Updating register 10 (R19), config: 2600 active: 2601. wm8775: Skipping register 11 (R20), config: 2826 active: 2826. wm8775: Updating register 12 (R21), config: 2a01 active: 2b0f. ivtv: i2c attach [client=wm8775[1],ok] tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 7855605 tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57) tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) tveeprom: audio_processor = MSP3410D (type = 5) ivtv: Tuner Type 57, Tuner formats 0x00001000, Radio: yes, Model 0x00914652, Revision 0xdccb10ec ivtv: NTSC tuner detected ivtv: Radio detected ivtv: Encoder revision: 0x02050032 ivtv: Encoder Firmware may be buggy, use version 0x02040011 ivtv: Configuring WinTV PVR 150 card with 5 streams ivtv: Create DMA stream 0 using 1024 16384 byte buffers 16777216 kbytes total ivtv: Registered v4l2 device, streamtype 0 minor 2 ivtv: Create DMA stream 1 ivtv: Registered v4l2 device, streamtype 1 minor 33 ivtv: Create stream 2 using 40 52224 byte buffers 2097152 kbytes total ivtv: Registered v4l2 device, streamtype 2 minor 226 ivtv: Create DMA stream 3 using 455 4608 byte buffers 2097152 kbytes total ivtv: Registered v4l2 device, streamtype 3 minor 25 ivtv: Create stream 4 ivtv: Registered v4l2 device, streamtype 4 minor 65 ivtv: Setting Tuner 57 tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #1 ivtv: Switching standard to NTSC. ivtv: Initialized WinTV PVR 150, card #1 ivtv: ==================== END INIT IVTV ====================
ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.3.2 (j) loading ivtv: Linux version: 2.6.10-1.770_14.rhfc3.at 686 REGPARM gcc-3.4 ivtv: In case of problems please include the debug info ivtv: between the START INIT IVTV and END INIT IVTV lines when ivtv: mailing the ivtv-devel mailinglist. ivtv: Autodetected WinTV PVR 150 card ivtv: Found an iTVC16 based chip ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 5 ACPI: PCI interrupt 0000:02:08.0[A] -> GSI 5 (level, low) -> IRQ 5 ivtv: Unreasonably low latency timer, setting to 64 (was 32) ivtv: XXX PCI device: 0x01e0 vendor: 0x10de ivtv: i2c attach [client=tveeprom,ok] tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 ivtv: i2c attach [client=(tuner unset),ok] tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 7855605 tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57) tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) tveeprom: audio_processor = MSP3410D (type = 5) ivtv: Tuner Type 57, Tuner formats 0x00001000, Radio: yes, Model 0x00914652, Revision 0xde230128 ivtv: NTSC tuner detected ivtv: Radio detected cx25840: Ignoring new-style parameters in presence of obsolete ones cx25840: FW image '/lib/modules/HcwMakoA.ROM' of size 14264 loaded. cx25840: FW image md5 digest: 3a4803384f749d644ee1f1ca9dcb12fa cx25840: FW image sha1 digest: 2b5e6292b7391c980b93d156cf6b34178ce770f6 ivtv: i2c attach [client=cx25840[0],ok] ivtv: i2c attach [client=wm8775[0],ok] ivtv: Encoder revision: 0x02050032 ivtv: Encoder Firmware may be buggy, use version 0x02040011 ivtv: Configuring WinTV PVR 150 card with 5 streams ivtv: Registered v4l2 device, streamtype 0 minor 1 ivtv: Create DMA stream 0 using 1024 16384 byte buffers 0 kbytes total ivtv: Allocate DMA stream 0 using 1024 16384 byte buffers 16777216 kbytes total ivtv: Registered v4l2 device, streamtype 1 minor 32 ivtv: Create DMA stream 1 ivtv: Allocate DMA stream 1 ivtv: Registered v4l2 device, streamtype 2 minor 225 ivtv: Create stream 2 using 40 52224 byte buffers 0 kbytes total ivtv: Allocate stream 2 using 40 52224 byte buffers 2097152 kbytes total ivtv: Registered v4l2 device, streamtype 3 minor 24 ivtv: Create DMA stream 3 using 455 4608 byte buffers 0 kbytes total ivtv: Allocate DMA stream 3 using 455 4608 byte buffers 2097152 kbytes total ivtv: Registered v4l2 device, streamtype 4 minor 64 ivtv: Create stream 4 ivtv: Allocate stream 4 ivtv: Setting Tuner 57 tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #0 ivtv: Switching standard to NTSC. ivtv: Initialized WinTV PVR 150, card #0 ivtv: Autodetected WinTV PVR 150 card ivtv: Found an iTVC16 based chip ivtv: ivtv_enc_thread: pid = 4494, itv = 0xde224f20 ACPI: PCI interrupt 0000:02:09.0[A] -> GSI 12 (level, low) -> IRQ 12 ivtv: Unreasonably low latency timer, setting to 64 (was 32) ivtv: XXX PCI device: 0x01e0 vendor: 0x10de ivtv: i2c attach [client=tveeprom,ok] tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #1 ivtv: i2c attach [client=(tuner unset),ok] cx25840: FW image '/lib/modules/HcwMakoA.ROM' of size 14264 loaded. cx25840: FW image md5 digest: 3a4803384f749d644ee1f1ca9dcb12fa cx25840: FW image sha1 digest: 2b5e6292b7391c980b93d156cf6b34178ce770f6 ivtv: i2c attach [client=cx25840[1],ok] ivtv: i2c attach [client=wm8775[1],ok] tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 7855605 tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57) tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) tveeprom: audio_processor = MSP3410D (type = 5) ivtv: Tuner Type 57, Tuner formats 0x00001000, Radio: yes, Model 0x00914652, Revision 0xde244634 ivtv: NTSC tuner detected ivtv: Radio detected ivtv: Encoder revision: 0x02050032 ivtv: Encoder Firmware may be buggy, use version 0x02040011 ivtv: Configuring WinTV PVR 150 card with 5 streams ivtv: Registered v4l2 device, streamtype 0 minor 2 ivtv: Create DMA stream 0 using 1024 16384 byte buffers 0 kbytes total ivtv: Allocate DMA stream 0 using 1024 16384 byte buffers 16777216 kbytes total ivtv: Registered v4l2 device, streamtype 1 minor 33 ivtv: Create DMA stream 1 ivtv: Allocate DMA stream 1 ivtv: Registered v4l2 device, streamtype 2 minor 226 ivtv: Create stream 2 using 40 52224 byte buffers 0 kbytes total ivtv: Allocate stream 2 using 40 52224 byte buffers 2097152 kbytes total ivtv: Registered v4l2 device, streamtype 3 minor 25 ivtv: Create DMA stream 3 using 455 4608 byte buffers 0 kbytes total ivtv: Allocate DMA stream 3 using 455 4608 byte buffers 2097152 kbytes total ivtv: Registered v4l2 device, streamtype 4 minor 65 ivtv: Create stream 4 ivtv: Allocate stream 4 ivtv: Setting Tuner 57 tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #1 ivtv: Switching standard to NTSC. ivtv: Initialized WinTV PVR 150, card #1 ivtv: ==================== END INIT IVTV ====================
