Hi,
I had no sound with 0.3.2w also - 0.3.2z works. You might want to try that. This is on my 150MCE, PAL.
Cheers,
-Morten
Allan Wilson wrote:
I have gotten everything but sound working properly. I have searched through some of the forums and mail lists but with no luck. Sorry to bother but any help would be appreciated. The following is from dmesg
ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.3.2 (w) loading ivtv: Linux version: 2.6.10-1.770_14.rhfc3.atsmp SMP 686 REGPARM gcc-3.4 ivtv: In case of problems please include the debug info ivtv: between the START INIT IVTV and END INIT IVTV lines when ivtv: mailing the ivtv-devel mailinglist. ivtv: Autodetected WinTV PVR 250 card ivtv: Found an iTVC16 based chip ACPI: PCI interrupt 0000:02:0a.0[A] -> GSI 22 (level, low) -> IRQ 177 ivtv: XXX PCI device: 0x2570 vendor: 0x8086 tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 ivtv: i2c attach [client=(tuner unset),ok] saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005) saa7115: detecting saa7115 client on address 0x42 saa7115: writing init values ivtv: i2c attach [client=saa7115[1],ok] saa7115: status: (1E) 0x81, (1F) 0xb1 tveeprom: Hauppauge: model = 32032, rev = B182, serial# = 2778996 tveeprom: tuner = LG TAPC H791F (idx = 82, type = 39) tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) tveeprom: audio_processor = MSP3440 (type = 11) ivtv: i2c attach [client=tveeprom[50],ok] ivtv: Failed to load module tveeprom ivtv: Tuner Type 39, Tuner formats 0x00001000, Radio: yes, Model 0x00891612, Revision 0x00000000 ivtv: NTSC tuner detected ivtv: Radio detected ivtv: Failed to load module msp3400 ivtv: Encoder revision: 0x02040011 ivtv: Configuring WinTV PVR 250 card with 5 streams ivtv: Registered v4l2 device, streamtype 0 minor 0 ivtv: Create DMA stream 0 using 1024 16384 byte buffers 0 kbytes total ivtv: Allocate DMA stream 0 using 1024 16384 byte buffers 16777216 kbytes totalivtv: Registered v4l2 device, streamtype 1 minor 32 ivtv: Create DMA stream 1 ivtv: Allocate DMA stream 1 ivtv: Registered v4l2 device, streamtype 2 minor 224 ivtv: Create stream 2 using 40 52224 byte buffers 0 kbytes total ivtv: Allocate stream 2 using 40 52224 byte buffers 2097152 kbytes total ivtv: Registered v4l2 device, streamtype 3 minor 24 ivtv: Create DMA stream 3 using 455 4608 byte buffers 0 kbytes total ivtv: Allocate DMA stream 3 using 455 4608 byte buffers 2097152 kbytes total ivtv: Registered v4l2 device, streamtype 4 minor 64 ivtv: Create stream 4 ivtv: Allocate stream 4 ivtv: Setting Tuner 39 tuner: type set to 39 (LG NTSC (newer TAPC series)) by ivtv i2c driver #0 saa7115: decoder set input (4) saa7115: now setting Composite input ivtv: Setting audio matrix to input 3, output 1 ivtv: i2c client addr: 0x40 not found! ivtv: i2c client addr: 0x40 not found! ivtv: i2c client addr: 0x40 not found! ivtv: Switching standard to NTSC. ivtv: i2c client addr: 0x40 not found! saa7115: decoder set norm NTSC ivtv: ivtv_enc_thread: pid = 7113, itv = 0xe2222da0 saa7115: set audio: 0x01 ivtv: Initialized WinTV PVR 250, card #0 ivtv: ==================== END INIT IVTV ====================
My /etc/modprobe.conf file alias eth0 sk98lin alias scsi_hostadapter ata_piix alias char-major-61 lirc_i2c alias snd-card-0 snd-intel8x0 options snd-card-0 index=0 install snd-intel8x0 /sbin/modprobe --ignore-install snd-intel8x0 && /usr/sbin/alsactl restore >/dev/null 2>&1 || : remove snd-intel8x0 { /usr/sbin/alsactl store >/dev/null 2>&1 || : ; }; /sbin/modprobe -r --ignore-remove snd-intel8x0 alias usb-controller ehci-hcd alias usb-controller1 uhci-hcd # nvidia kernel module alias char-major-195 nvidia-1_0-7174 alias nvidia nvidia-1_0-7174 # ivtv modules setup alias char-major-81 videodev alias char-major-81-0 ivtv alias tveeprom tveeprom-ivtv alias msp3400 msp3400-ivtv options ivtv ivtv_debug=1 tuner=39 #options ivtv ivtv_debug=1 tuner=47 # lirc for remote control #install lirc_i2c /sbin/modprobe ivtv; /sbin/modprobe --ignore-install lirc_i2c
I read in earlier posts to make sure that I was using the correct msp3400 so I deleted all msp3400.ko files and reinstall ivtv but this did not seem to help. I have also unmuted everything in Gnome's volume control. I am using FC3. Any ideas? Thanks for the help.
-------------------------------------------------------
This SF.Net email is sponsored by: New Crystal Reports XI.
Version 11 adds new functionality designed to reduce time involved in
creating, integrating, and deploying reporting solutions. Free runtime info,
new features, or free trial, at: http://www.businessobjects.com/devxi/728
_______________________________________________
ivtv-devel mailing list
ivtv-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/ivtv-devel
-- ------------------------------------------------------------------- WEB-fx Morten Lerskau Rønseth http://www.webfx.no Odinsvei 15c mailto:[EMAIL PROTECTED] 1413 Tårnåsen Tlf.: (47) 6680 9191 Norway Mob : (47) 9343 4357
------------------------------------------------------- This SF.Net email is sponsored by: New Crystal Reports XI. Version 11 adds new functionality designed to reduce time involved in creating, integrating, and deploying reporting solutions. Free runtime info, new features, or free trial, at: http://www.businessobjects.com/devxi/728 _______________________________________________ ivtv-devel mailing list ivtv-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/ivtv-devel
