Hi Chris,
I'm curious if you have any ideas why the PVR-500 rev D492 seem to be
giving so many people issues with just getting static on the tuner?I've tried every combination of modules.conf settings, firmware versions, and ivtv versions that I can think of, and even tried the card in two different machines, still no luck. The cards composite input does work fine though, just not the tuner. Any insight would be greatly appreciated. Thanks. On Fri, 2005-05-06 at 23:44 -0500, Chris Kennedy wrote: > This happens on one motherboard of mine, not on another, others have > reported similar results, seems these cards don't like every motherboard, > seem like quite a complex device so just figures they would be difficult > (I really wish I could use mine in my pvr, double my inputs, kinda > depressing). > > Thanks, > Chris > On Fri, May 06, 2005 at 11:37:32PM -0500, James A. Pattie wrote: > > -----BEGIN PGP SIGNED MESSAGE----- > > Hash: SHA1 > > > > Just got my PVR-500 rev D492 and built 2.6.11.8 from scratch on Debian > > testing > > (just updated to latest today). > > > > I've tried with both 0.2.0-rc3j and 0.3.4b and when I go and do an > > mplayer <options here> /dev/video1 the machine instantly reboots > > or it may not reboot until I try to tune to a channel, since all I'm > > getting is > > static. > > > > I've had it happen with both /dev/video0 and /dev/video1. > > > > I was getting good picture/sound from 0.3.4b, but only from /dev/video1 and > > then > > I rebooted and plugged in the 2nd connector (svideo and composite). I > > wonder if > > plugging that in backwards, which I thought it was keyed, would cause the > > rebooting? > > > > Question for other pvr-500 owners: Do you only have 1 antenna connector > > for tv > > and does the card internally multiplex it? My second connector doesn't > > have an > > antenna jack on it, just svideo and composite inputs. > > > > Here's the output from 0.2.0-rc3j. I'll try with 0.3.4c after sending this > > e-mail. > > > > Linux video capture interface: v1.00 > > ivtv: ==================== START INIT IVTV ==================== > > ivtv: version 0.2.0 (rc3j) loading > > ivtv: Linux version: 2.6.11.8-pcx-1-k7 preempt K7 gcc-3.3 > > ivtv: In case of problems please include the debug info > > ivtv: between the START INIT IVTV and END INIT IVTV lines when > > ivtv: mailing the ivtv-devel mailinglist. > > ivtv: Autodetected WinTV PVR 150 card > > ivtv: Found an iTVC16 based chip > > ACPI: PCI interrupt 0000:02:08.0[A] -> GSI 10 (level, low) -> IRQ 10 > > ivtv: VIA PCI device: 0x0305 vendor: 0x1106 > > tveeprom: The eeprom says no radio is present, but the tuner type > > tveeprom: indicates otherwise. I will assume that radio is present. > > tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 8023497 > > tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57) > > tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) > > tveeprom: audio_processor = MSP3410D (type = 5) > > ivtv: i2c attach [client=tveeprom[2],ok] > > tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 > > ivtv: i2c attach [client=(tuner unset),ok] > > cx25840: FW image '/lib/modules/HcwMakoA.ROM' of size 14264 loaded. > > cx25840: FW image md5 digest: 3a4803384f749d644ee1f1ca9dcb12fa > > cx25840: FW image sha1 digest: 2b5e6292b7391c980b93d156cf6b34178ce770f6 > > ivtv: i2c attach [client=cx25840[2],ok] > > wm8775: Setting register ADCFMT (7) to 1, R11.0..1, old value 02 > > wm8775: Setting register ADCMS (8) to 1, R12.8..8, old value 00 > > wm8775: Setting register DCY (24) to 8, R18.4..7, old value 03 > > wm8775: Setting register NGAT (27) to 1, R19.0..0, old value 00 > > wm8775: Setting register LRBOTH (30) to 1, R21.8..8, old value 00 > > wm8775: Setting register AMX (33) to 15, R21.0..3, old value 01 > > wm8775: Updating register 0 (R23), config: 2e01 active: 2e00. > > wm8775: Skipping register 1 (R7), config: 0e00 active: 0e00. > > wm8775: Updating register 2 (R11), config: 1622 active: 1621. > > wm8775: Updating register 3 (R12), config: 1802 active: 1902. > > wm8775: Skipping register 4 (R13), config: 1a00 active: 1a00. > > wm8775: Skipping register 5 (R14), config: 1ccf active: 1ccf. > > wm8775: Skipping register 6 (R15), config: 1ecf active: 1ecf. > > wm8775: Skipping register 7 (R16), config: 207b active: 207b. > > wm8775: Skipping register 8 (R17), config: 2200 active: 2200. > > wm8775: Updating register 9 (R18), config: 2432 active: 2482. > > wm8775: Updating register 10 (R19), config: 2600 active: 2601. > > wm8775: Skipping register 11 (R20), config: 2826 active: 2826. > > wm8775: Updating register 12 (R21), config: 2a01 active: 2b0f. > > ivtv: i2c attach [client=wm8775[2],ok] > > ivtv: Tuner Type 57, Tuner formats 0x00001000, Radio: yes, Model 0x00914652, > > Revision 0x00000001 > > ivtv: NTSC tuner detected > > ivtv: Radio detected > > ivtv: Encoder revision: 0x02050032 > > ivtv: Encoder Firmware may be buggy, use version 0x02040011 > > ivtv: Configuring WinTV PVR 150 card with 5 streams > > ivtv: Create DMA stream 0 using 256 16384 byte buffers 4194304 kbytes total > > ivtv: Registered v4l2 device, streamtype 0 minor 0 > > ivtv: Create DMA stream 1 > > ivtv: Registered v4l2 device, streamtype 1 minor 32 > > ivtv: Create stream 2 using 40 52224 byte buffers 2097152 kbytes total > > ivtv: Registered v4l2 device, streamtype 2 minor 224 > > ivtv: Create DMA stream 3 using 455 4608 byte buffers 2097152 kbytes total > > ivtv: Registered v4l2 device, streamtype 3 minor 24 > > ivtv: Create stream 4 > > ivtv: Registered v4l2 device, streamtype 4 minor 64 > > ivtv: Setting Tuner 57 > > tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #0 > > ivtv: ivtv_enc_thread: pid = 3591, itv = 0xe0ca0fe0 > > ivtv: Switching standard to NTSC. > > ivtv: Initialized WinTV PVR 150, card #0 > > ivtv: Autodetected WinTV PVR 150 card > > ivtv: Found an iTVC16 based chip > > ACPI: PCI interrupt 0000:02:09.0[A] -> GSI 11 (level, low) -> IRQ 11 > > ivtv: VIA PCI device: 0x0305 vendor: 0x1106 > > tveeprom: The eeprom says no radio is present, but the tuner type > > tveeprom: indicates otherwise. I will assume that radio is present. > > tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 8023497 > > tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57) > > tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) > > tveeprom: audio_processor = MSP3410D (type = 5) > > ivtv: i2c attach [client=tveeprom[3],ok] > > tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #1 > > ivtv: i2c attach [client=(tuner unset),ok] > > cx25840: FW image '/lib/modules/HcwMakoA.ROM' of size 14264 loaded. > > cx25840: FW image md5 digest: 3a4803384f749d644ee1f1ca9dcb12fa > > cx25840: FW image sha1 digest: 2b5e6292b7391c980b93d156cf6b34178ce770f6 > > ivtv: i2c attach [client=cx25840[3],ok] > > wm8775: Setting register ADCFMT (7) to 1, R11.0..1, old value 02 > > wm8775: Setting register ADCMS (8) to 1, R12.8..8, old value 00 > > wm8775: Setting register DCY (24) to 8, R18.4..7, old value 03 > > wm8775: Setting register NGAT (27) to 1, R19.0..0, old value 00 > > wm8775: Setting register LRBOTH (30) to 1, R21.8..8, old value 00 > > wm8775: Setting register AMX (33) to 15, R21.0..3, old value 01 > > wm8775: Updating register 0 (R23), config: 2e01 active: 2e00. > > wm8775: Skipping register 1 (R7), config: 0e00 active: 0e00. > > wm8775: Updating register 2 (R11), config: 1622 active: 1621. > > wm8775: Updating register 3 (R12), config: 1802 active: 1902. > > wm8775: Skipping register 4 (R13), config: 1a00 active: 1a00. > > wm8775: Skipping register 5 (R14), config: 1ccf active: 1ccf. > > wm8775: Skipping register 6 (R15), config: 1ecf active: 1ecf. > > wm8775: Skipping register 7 (R16), config: 207b active: 207b. > > wm8775: Skipping register 8 (R17), config: 2200 active: 2200. > > wm8775: Updating register 9 (R18), config: 2432 active: 2482. > > wm8775: Updating register 10 (R19), config: 2600 active: 2601. > > wm8775: Skipping register 11 (R20), config: 2826 active: 2826. > > wm8775: Updating register 12 (R21), config: 2a01 active: 2b0f. > > ivtv: i2c attach [client=wm8775[3],ok] > > ivtv: Tuner Type 57, Tuner formats 0x00001000, Radio: yes, Model 0x00914652, > > Revision 0x00000001 > > ivtv: NTSC tuner detected > > ivtv: Radio detected > > ivtv: Encoder revision: 0x02050032 > > ivtv: Encoder Firmware may be buggy, use version 0x02040011 > > ivtv: Configuring WinTV PVR 150 card with 5 streams > > ivtv: Create DMA stream 0 using 256 16384 byte buffers 4194304 kbytes total > > ivtv: Registered v4l2 device, streamtype 0 minor 1 > > ivtv: Create DMA stream 1 > > ivtv: Registered v4l2 device, streamtype 1 minor 33 > > ivtv: Create stream 2 using 40 52224 byte buffers 2097152 kbytes total > > ivtv: Registered v4l2 device, streamtype 2 minor 225 > > ivtv: Create DMA stream 3 using 455 4608 byte buffers 2097152 kbytes total > > ivtv: Registered v4l2 device, streamtype 3 minor 25 > > ivtv: Create stream 4 > > ivtv: Registered v4l2 device, streamtype 4 minor 65 > > ivtv: Setting Tuner 57 > > tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #1 > > ivtv: Switching standard to NTSC. > > ivtv: Initialized WinTV PVR 150, card #1 > > ivtv: ==================== END INIT IVTV ==================== > > ivtv: ivtv_enc_thread: pid = 3612, itv = 0xe0cb52a0 > > > > - -- > > James A. Pattie > > [EMAIL PROTECTED] > > > > Linux -- SysAdmin / Programmer > > Xperience, Inc. > > http://www.pcxperience.com/ > > http://www.xperienceinc.com/ > > http://www.pcxperience.org/ > > > > GPG Key Available at http://www.pcxperience.com/gpgkeys/james.html > > -----BEGIN PGP SIGNATURE----- > > Version: GnuPG v1.2.5 (GNU/Linux) > > Comment: Using GnuPG with Thunderbird - http://enigmail.mozdev.org > > > > iD8DBQFCfEYLtUXjwPIRLVERAmKNAJ4hxIMNlonhK+R9aMZS3dOsgNzfIACfb4/L > > vfOnDfv++QjOqpt/fec3zHI= > > =b5YJ > > -----END PGP SIGNATURE----- > > > > -- > > This message has been scanned for viruses and > > dangerous content by MailScanner, and is > > believed to be clean. > > MailScanner thanks transtec Computers for their support. > > > > > > > > ------------------------------------------------------- > > This SF.Net email is sponsored by: NEC IT Guy Games. > > Get your fingers limbered up and give it your best shot. 4 great events, 4 > > opportunities to win big! Highest score wins.NEC IT Guy Games. Play to > > win an NEC 61 plasma display. Visit http://www.necitguy.com/?r=20 > > _______________________________________________ > > ivtv-devel mailing list > > [email protected] > > https://lists.sourceforge.net/lists/listinfo/ivtv-devel > -- Mike Benoit <[EMAIL PROTECTED]>
signature.asc
Description: This is a digitally signed message part
