MIchel, Christian- Try using the parameter tda9887=0 for the ivtv module. Michel Verbraak wrote: > Christian, > > I have the same problem. It is only for my PVR-150. The PVR-350 I have > is rock solid. But for the PVR-150 if I do a cold reboot (power down) > than I only get static. When I use an older version 0.3.4p i get a good > functioning PVR-150 even after a cold reboot. > > I did not yet try version 0.3.5f. Will try it later today. > > Regards, > > Michel. > > Christian Viller Hansen wrote: > > > Hi > > > > To be able to use the tuner with the new drivers (at least d and f) I > > have to load an old driver first. The video taken from a cold reboot: > > > > http://viller.org/150mce_0.3.5f.mpeg (don't download it if you pay pr. > > mb because it's only black with some noise and blocks. It's not > > something funny like Dr. Phil) > > > > It works really well if load 0.3.4v, then unload it and load 0.3.5d. I > > haven't tried the same procedure with f, but I'm expecting the same > > behaviour. Is that the init of registers stuff you have been talking > > about? I have attached my dmesg output in the bottom. > > > > > > Regards > > Christian > > > > ivtv: ==================== START INIT IVTV ==================== > > ivtv: version 0.3.5 (f) loading > > ivtv: Linux version: 2.6.11 preempt PENTIUM4 gcc-3.3 > > ivtv: In case of problems please include the debug info > > ivtv: between the START INIT IVTV and END INIT IVTV lines when > > ivtv: mailing the ivtv-devel mailinglist. > > ivtv: Autodetected WinTV PVR 150 card > > ivtv: Found an iTVC16 based chip > > ACPI: PCI interrupt 0000:00:0d.0[A] -> GSI 17 (level, low) -> IRQ 17 > > ivtv: XXX PCI device: 0x0648 vendor: 0x1039 > > tveeprom: Hauppauge: model = 26559, rev = C260, serial# = 7705475 > > tveeprom: tuner = LG S001D MK3 (idx = 60, type = 58) > > tveeprom: tuner fmt = PAL(B/G) PAL(I) SECAM(L/L) PAL(D/K) (eeprom = > > 0x74, v4l2 = 0x00400e17) > > tveeprom: audio_processor = MSP3410D (type = 5) > > ivtv: i2c attach [client=tveeprom[50],ok] > > ivtv: Tuner Type 58, Tuner formats 0x00400e17, Radio: yes, Model > > 0x008d2590, Revision 0x00000001 > > ivtv: Radio detected > > tuner: Ignoring new-style parameters in presence of obsolete ones > > tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 > > ivtv: i2c attach [client=(tuner unset),ok] > > cx25840: starting probe for adapter ivtv i2c driver #0 (0x10005) > > cx25840: detecting client on address 0x88 > > cx25840: writing init values > > cx25840: FW image '/lib/modules/HcwMakoA.ROM' of size 14264 loaded. > > cx25840: FW image md5 digest: 3a4803384f749d644ee1f1ca9dcb12fa > > cx25840: FW image sha1 digest: 2b5e6292b7391c980b93d156cf6b34178ce770f6 > > cx25840: Status: cx258433 (DEVICE_ID) > > ivtv: i2c attach [client=cx25840[50],ok] > > ivtv: i2c attach [client=wm8775[50],ok] > > ivtv: Encoder revision: 0x02040011 > > ivtv: Configuring WinTV PVR 150 card with 5 streams > > ivtv: Registered v4l2 device, streamtype 0 minor 0 > > ivtv: Create DMA stream 0 using 128 16384 byte buffers 0 kbytes total > > ivtv: Registered v4l2 device, streamtype 1 minor 32 > > ivtv: Create DMA stream 1 using 80 25920 byte buffers 0 kbytes total > > ivtv: Registered v4l2 device, streamtype 2 minor 224 > > ivtv: Create DMA stream 2 using 41 50540 byte buffers 0 kbytes total > > ivtv: Registered v4l2 device, streamtype 3 minor 24 > > ivtv: Create DMA stream 3 using 455 4608 byte buffers 0 kbytes total > > ivtv: Registered v4l2 device, streamtype 4 minor 64 > > ivtv: Create stream 4 > > ivtv: Setting Tuner 58 > > tuner: type set to 58 (LG PAL TAPE-S001D) by ivtv i2c driver #0 > > ivtv: ivtv_enc_thread: pid = 5305, itv = 0xe0f09aa0 > > ivtv: ivtv_enc_vbi_thread: pid = 5306, itv = 0xe0f09aa0 > > cx25840: decoder set norm PAL > > cx25840: decoder set input (6) > > cx25840: Tuner Input > > cx25840: set_audio_input 0 > > ivtv: Switching standard to PAL. > > cx25840: decoder set norm PAL > > ivtv: Initialized WinTV PVR 150, card #0 > > ivtv: ==================== END INIT IVTV ==================== > > > > > > > > ------------------------------------------------------- > > This SF.Net email is sponsored by Oracle Space Sweepstakes > > Want to be the first software developer in space? > > Enter now for the Oracle Space Sweepstakes! > > http://ads.osdn.com/?ad_id=7412&alloc_id=16344&op=click > > _______________________________________________ > > ivtv-devel mailing list > > [email protected] > > https://lists.sourceforge.net/lists/listinfo/ivtv-devel > > > > > ------------------------------------------------------- > This SF.Net email is sponsored by Oracle Space Sweepstakes > Want to be the first software developer in space? > Enter now for the Oracle Space Sweepstakes! > http://ads.osdn.com/?ad_id=7412&alloc_id=16344&op=click > _______________________________________________ > ivtv-devel mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/ivtv-devel >
-- Tyler Trafford ------------------------------------------------------- This SF.Net email is sponsored by Yahoo. Introducing Yahoo! Search Developer Network - Create apps using Yahoo! Search APIs Find out how you can build Yahoo! directly into your own Applications - visit http://developer.yahoo.net/?fr=offad-ysdn-ostg-q22005 _______________________________________________ ivtv-devel mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/ivtv-devel
