The ivtvdev version is printed in the X log file (just after it loads it). The main version is 10.0 The version i pushed out last night identifies itself as 10.1 & also the messages in the X log file say IVTVDEV_TST instead of just IVTVDEV so i can identify if that variant is being used.
John --- "Patrick de Brabander [mythtv]" <[EMAIL PROTECTED]> wrote: > Mine experience is that livetv is working, but the > controls are extremly > slow. > Also OSD and EPG are not showing on the screen. > YUV is working fine, i can switch between livetv and > video. > > I've attached a piece of my messages.log. No strange > errors noticed. > > Using 0.3.5f and iivtvdev 1.0 (i believe, no version > attached) > > Maybe it is possible to let show a version number in > the log file like ivtv. > > Gr. > > Patrick > > > > -----Oorspronkelijk bericht----- > > Van: [EMAIL PROTECTED] > > [mailto:[EMAIL PROTECTED] > Namens John Harvey > > Verzonden: dinsdag 24 mei 2005 12:53 > > Aan: [email protected] > > Onderwerp: Re: [ivtv-devel] .3.5f report. YUV > working well, > > getting crashes though. > > > > With Myth it's getting the vbi insertion stuff > enabled which > > is asking for more memory which is failing. With > just dd'ing > > i doubt it is doing that. > > As for the 2nd crash i have no idea but i may look > later tonight. > > > > Can you send me a complete log from ivtv_init to > the first > > crash and i'll take a look through the buffer > allocation. > > Since i don't actually need any buffers in the Xv > case for > > YUV output i will probably try to stop it > allocating it for that case. > > > > John > > --- Lucas Meijer <[EMAIL PROTECTED]> wrote: > > > Heya. > > > > > > With 3.5f I can switch between mpeg decoding, > yuv decoding > > as much as > > > I like. Whenever I throw in myth's livetv > however, things go bad. > > > Either I crash when starting up livetv, or the > next > > recording I watch > > > after having been in livetv. I've tried a lot of > times, and > > have seen > > > two different looking types of problems in > dmesg. > > > Both of them pasted > > > below: > > > > > > ivtv: Allocate DMA stream 0 using 128 16384 byte > buffers 2097152 > > > kbytes total > > > ivtv: Allocate DMA stream 2 using 41 50540 byte > buffers 2097152 > > > kbytes total > > > ivtv: Setup VBI API header 0x0000bd06 pkts 1 > buffs > > > 48 ln 34 sz 64 > > > ivtv: Setup VBI start 0x0018ea04 frames 48 fpi 1 > lines 0x000000f1 > > > saa7115: decoder disable output > > > saa7115: decoder enable output > > > ivtv: VBI insertion started > > > ivtv: Allocate DMA stream 5 using 16 65536 byte > buffers 1048576 > > > ..................................... > > May 24 18:44:21 localhost kernel: ivtv: > ==================== START INIT IVTV > ==================== > May 24 18:44:21 localhost kernel: ivtv: version > 0.3.5 (f) loading > May 24 18:44:21 localhost kernel: ivtv: Linux > version: 2.6.10-1.771_FC2 686 REGPARM 4KSTACKS > gcc-3.3 > May 24 18:44:21 localhost kernel: ivtv: In case of > problems please include the debug info > May 24 18:44:21 localhost kernel: ivtv: between the > START INIT IVTV and END INIT IVTV lines when > May 24 18:44:21 localhost kernel: ivtv: mailing the > ivtv-devel mailinglist. > May 24 18:44:21 localhost kernel: ivtv: Autodetected > WinTV PVR 350 card > May 24 18:44:21 localhost kernel: ivtv: Found an > iTVC15 based chip > May 24 18:44:23 localhost kernel: PCI: Found IRQ 10 > for device 0000:02:0a.0 > May 24 18:44:23 localhost kernel: ivtv: XXX PCI > device: 0x1130 vendor: 0x8086 > May 24 18:44:23 localhost kernel: tveeprom: > Hauppauge: model = 48139, rev = K257, serial# = > 7596027 > May 24 18:44:24 localhost kernel: tveeprom: tuner = > Philips FM1216 ME MK3 (idx = 57, type = 38) > May 24 18:44:25 localhost kernel: tveeprom: tuner > fmt = PAL(B/G) PAL(I) SECAM(L/L) PAL(D/K) (eeprom = > 0x74, v4l2 = 0x00400e17) > May 24 18:44:25 localhost kernel: tveeprom: > audio_processor = CS5331 (type = 9) > May 24 18:44:25 localhost kernel: ivtv: i2c attach > [client=tveeprom[50],ok] > May 24 18:44:25 localhost kernel: ivtv: Tuner Type > 38, Tuner formats 0x00400e17, Radio: yes, Model > 0x00ad2557, Revision 0x00000001 > May 24 18:44:25 localhost kernel: ivtv: Radio > detected > May 24 18:44:25 localhost kernel: tuner: Ignoring > new-style parameters in presence of obsolete ones > May 24 18:44:25 localhost kernel: tuner: chip found > at addr 0xc2 i2c-bus ivtv i2c driver #0 > May 24 18:44:25 localhost kernel: ivtv: i2c attach > [client=(tuner unset),ok] > May 24 18:44:26 localhost kernel: saa7115: starting > probe for adapter ivtv i2c driver #0 (0x10005) > May 24 18:44:26 localhost kernel: saa7115: detecting > saa7115 client on address 0x42 > May 24 18:44:26 localhost kernel: saa7115: writing > init values > May 24 18:44:27 localhost kernel: ivtv: i2c attach > [client=saa7115[50],ok] > May 24 18:44:27 localhost kernel: saa7115: status: > (1E) 0x00, (1F) 0xc0 > May 24 18:44:27 localhost kernel: saa7127: Ignoring > new-style parameters in presence of obsolete ones > May 24 18:44:27 localhost kernel: saa7127: video > encoder driver version V 0.3 loaded > May 24 18:44:27 localhost kernel: saa7127: detecting > saa7127 client on address 0x88 > May 24 18:44:27 localhost kernel: saa7127: Selecting > NTSC video Standard > May 24 18:44:27 localhost kernel: saa7127: Selecting > S-Video+Composite > May 24 18:44:27 localhost kernel: saa7127: Turn WSS > off > May 24 18:44:27 localhost kernel: saa7127: > Widescreen Mode 4:3 Full Format > May 24 18:44:27 localhost lircd-0.7.1[2795]: > lircd(any) ready > May 24 18:44:27 localhost lircd: lircd start op > succeeded > May 24 18:44:28 localhost kernel: saa7127: Selecting > Normal Encoder Input > May 24 18:44:29 localhost lircd-0.7.1[2795]: > accepted new client on /dev/lircd > May 24 18:44:30 localhost kernel: saa7127: Enable > Video Output > May 24 18:44:30 localhost kernel: ivtv: i2c attach > [client=saa7127[50],ok] > May 24 18:44:30 localhost kernel: msp34xx: ivtv > version > May 24 18:44:30 localhost kernel: msp34xx: init: > chip=MSP3418W-B3, has NICAM support, simple (D) > mode, simpler (G) no-thread mode > May 24 18:44:30 localhost kernel: msp34xx: $Id$ > compiled on: May 24 2005 18:38:25 > May 24 18:44:30 localhost kernel: ivtv: i2c attach > [client=MSP3418W-B3,ok] > May 24 18:44:30 localhost kernel: tda9885/6/7: chip > found @ 0x86 > May 24 18:44:30 localhost kernel: ivtv: i2c attach > [client=tda9887,ok] > May 24 18:44:30 localhost kernel: ivtv: Encoder > revision: 0x02040011 > May 24 18:44:30 localhost kernel: ivtv: Decoder > revision: 0x02020023 > May 24 18:44:30 localhost kernel: ivtv: Configuring > WinTV PVR 350 card with 10 streams > May 24 18:44:30 localhost kernel: ivtv: Registered > v4l2 device, streamtype 0 minor 0 > May 24 18:44:30 localhost kernel: ivtv: Create DMA > stream 0 using 128 16384 byte buffers 0 kbytes > total > May 24 18:44:30 localhost kernel: ivtv: Registered > v4l2 device, streamtype 1 minor 32 > May 24 18:44:30 localhost kernel: ivtv: Create DMA > stream 1 using 80 25920 byte buffers 0 kbytes total > May 24 18:44:30 localhost kernel: ivtv: Registered > v4l2 device, streamtype 2 minor 224 > May 24 18:44:30 localhost kernel: ivtv: Create DMA > stream 2 using 41 50540 byte buffers 0 kbytes total > May 24 18:44:30 localhost kernel: ivtv: Registered > v4l2 device, streamtype 3 minor 24 > May 24 18:44:30 localhost kernel: ivtv: Create DMA > stream 3 using 455 4608 byte buffers 0 kbytes total > May 24 18:44:30 localhost kernel: ivtv: Registered > v4l2 device, streamtype 4 minor 64 > May 24 18:44:30 localhost kernel: ivtv: Create > stream 4 > May 24 18:44:30 localhost kernel: ivtv: Registered > v4l2 device, streamtype 5 minor 16 > May 24 18:44:30 localhost kernel: ivtv: Create DMA > stream 5 using 16 65536 byte buffers 0 kbytes total > May 24 18:44:30 localhost kernel: ivtv: Registered > v4l2 device, streamtype 6 minor 228 > May 24 18:44:30 localhost kernel: ivtv: Create DMA > stream 6 using 1024 2048 byte buffers 0 kbytes > total > May 24 18:44:30 localhost kernel: ivtv: Registered > v4l2 device, streamtype 7 minor 232 > May 24 18:44:30 localhost kernel: ivtv: Create > stream 7 > May 24 18:44:30 localhost kernel: ivtv: Registered > v4l2 device, streamtype 8 minor 48 > May 24 18:44:30 localhost kernel: ivtv: Create DMA > stream 8 using 80 25920 byte buffers 0 kbytes total > May 24 18:44:30 localhost kernel: ivtv: Create DMA > stream 9 using 32 65536 byte buffers 0 kbytes total > May 24 18:44:30 localhost kernel: ivtv: Setting > Tuner 38 > May 24 18:44:30 localhost kernel: tuner: type set to > 38 (Philips PAL/SECAM multi (FM1216ME MK3)) by ivtv > i2c driver #0 > May 24 18:44:30 localhost kernel: saa7115: decoder > set norm PAL > May 24 18:44:30 localhost kernel: saa7115: set > audio: 0x01 > May 24 18:44:30 localhost kernel: saa7115: decoder > set input (4) > May 24 18:44:30 localhost kernel: saa7115: now > setting Composite input > May 24 18:44:30 localhost kernel: ivtv: Setting > audio matrix to input 3, output 1 > May 24 18:44:30 localhost kernel: ivtv: Switching > standard to PAL. > May 24 18:44:30 localhost kernel: ivtv: > ivtv_enc_thread: pid = 2566, itv = 0xe0dff6a0 > May 24 18:44:30 localhost kernel: ivtv: > ivtv_enc_vbi_thread: pid = 2567, itv = 0xe0dff6a0 > May 24 18:44:30 localhost kernel: ivtv: > ivtv_dec_thread: pid = 2568, itv = 0xe0dff6a0 > May 24 18:44:30 localhost kernel: ivtv: > ivtv_dec_vbi_thread: pid = 2569, itv = 0xe0dff6a0 > May 24 18:44:30 localhost kernel: saa7115: decoder > set norm PAL > May 24 18:44:30 localhost kernel: saa7115: set > audio: 0x01 > May 24 18:44:30 localhost kernel: saa7127: Setting > Encoder Video Standard > May 24 18:44:30 localhost kernel: saa7127: Set PAL > Video Mode > May 24 18:44:30 localhost kernel: saa7127: Selecting > PAL video Standard > May 24 18:44:30 localhost kernel: ivtv: Initialized > WinTV PVR 350, card #0 > May 24 18:44:30 localhost kernel: ivtv: > ==================== END INIT IVTV > ==================== > May 24 18:44:30 localhost kernel: ivtv-osd: > Framebuffer module loaded (attached to ivtv card id > 0) > May 24 18:44:30 localhost kernel: ivtv-osd: > Framebuffer is at decoder-relative address > 0x00510000 and has 1704960 bytes. > May 24 18:44:30 localhost kernel: ivtv-osd: screen > coords: [0 0] -> [720 576] > May 24 18:44:30 localhost kernel: ivtv-osd: original > global alpha = 208 > May 24 18:44:31 localhost kernel: ivtv-osd: current > OSD state = 39 > May 24 18:44:31 localhost kernel: ivtv-osd: new > global alpha = 208 (1 255 0) > May 24 18:44:31 localhost kernel: ivtv-osd: > framebuffer at 0x45510000, mapped to 0xe1d10000, > size 1620k > May 24 18:44:31 localhost kernel: ivtv-osd: mode is > 720x576x32, linelength=2880 > May 24 18:44:31 localhost kernel: Console: switching > to colour frame buffer device 90x36 > === message truncated === ------------------------------------------------------- This SF.Net email is sponsored by Yahoo. Introducing Yahoo! Search Developer Network - Create apps using Yahoo! Search APIs Find out how you can build Yahoo! directly into your own Applications - visit http://developer.yahoo.net/?fr=offad-ysdn-ostg-q22005 _______________________________________________ ivtv-devel mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/ivtv-devel
