Hi, I got a pvr150 (not mce). I saw the following when loading the module: tveeprom: Encountered bad packet header [ff]. Corrupt or not a Hauppauge eeprom.
Should I be concerned, thanks.. Here is the full output of syslog: ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.3.5 (l) loading ivtv: Linux version: 2.6.10-1.770_FC3 686 REGPARM 4KSTACKS gcc-3.4 ivtv: In case of problems please include the debug info ivtv: between the START INIT IVTV and END INIT IVTV lines when ivtv: mailing the ivtv-devel mailinglist. ivtv: Autodetected WinTV PVR 150 card ivtv: Found an iTVC16 based chip ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 10 (level, low) -> IRQ 10 ivtv: Unreasonably low latency timer, setting to 64 (was 32) ivtv: VIA PCI device: 0x3189 vendor: 0x1106 tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 ivtv: i2c attach [client=(tuner unset),ok] tveeprom: Encountered bad packet header [ff]. Corrupt or not a Hauppauge eeprom. tveeprom: Hauppauge: model = 26032, rev = C199, serial# = 2984694 tveeprom: tuner = TCL 2002N 5H (idx = 99, type = 50) tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) tveeprom: audio_processor = TDA9850 (type = 3) ivtv: i2c attach [client=tveeprom[50],ok] ivtv: Tuner Type 50, Tuner formats 0x00001000, Radio: yes, Model 0x008d1659, Rev ision 0x00000000 ivtv: Radio detected cx25840: starting probe for adapter bt878 #0 [sw] (0x10005) cx25840: starting probe for adapter ivtv i2c driver #0 (0x10005) cx25840: detecting cx25840 client on address 0x88 cx25840: writing init values cx25840: FW image '/lib/modules/HcwMakoA.ROM' of size 14264 loaded. cx25840: FW image md5 digest: 3a4803384f749d644ee1f1ca9dcb12fa cx25840: FW image sha1 digest: 2b5e6292b7391c980b93d156cf6b34178ce770f6 cx25840: Status: cx258413 (DEVICE_ID) ivtv: i2c attach [client=cx25840[50],ok] ivtv: i2c attach [client=wm8775[50],ok] ivtv: Encoder revision: 0x02040024 ivtv: Encoder Firmware may be buggy, use version 0x02040011 ivtv: Configuring WinTV PVR 150 card with 5 streams ivtv: Registered v4l2 device, streamtype 0 minor 1 ivtv: Create DMA stream 0 using 128 16384 byte buffers 0 kbytes total ivtv: Registered v4l2 device, streamtype 1 minor 32 ivtv: Create DMA stream 1 using 97 21600 byte buffers 0 kbytes total ivtv: Registered v4l2 device, streamtype 2 minor 225 ivtv: Create DMA stream 2 using 60 34656 byte buffers 0 kbytes total ivtv: Registered v4l2 device, streamtype 3 minor 24 ivtv: Create DMA stream 3 using 455 4608 byte buffers 0 kbytes total ivtv: Registered v4l2 device, streamtype 4 minor 65 ivtv: Create stream 4 ivtv: Setting Tuner 50 tuner: type set to 50 (TCL 2002N) by ivtv i2c driver #0 cx25840: decoder set norm NTSC cx25840: decoder set input (6) cx25840: now setting Tuner input cx25840: set audio input (0) ivtv: Switching standard to NTSC. ivtv: Initialized WinTV PVR 150, card #0 ivtv: ==================== END INIT IVTV ==================== ivtv: ivtv_enc_thread: pid = 5910, itv = 0xf8d88c20 ivtv: ivtv_enc_vbi_thread: pid = 5911, itv = 0xf8d88c20 ------------------------------------------------------- This SF.Net email is sponsored by: NEC IT Guy Games. How far can you shotput a projector? How fast can you ride your desk chair down the office luge track? If you want to score the big prize, get to know the little guy. Play to win an NEC 61" plasma display: http://www.necitguy.com/?r _______________________________________________ ivtv-devel mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/ivtv-devel
