Hello, After the above message, the card doesn't give any data until I perform a reset of the computer.
This is with version 0.3.7C of the ivtv driver. The problem occurs when I try to read from the same drive that is saving captured data. Is there a way to either avoid this problem, or get the card going again without reboot? ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.3.7 (c) loading ivtv: Linux version: 2.6.11.11 SMP preempt K7 4KSTACKS gcc-3.3 ivtv: In case of problems please include the debug info ivtv: between the START INIT IVTV and END INIT IVTV lines when ivtv: mailing the ivtv-devel mailinglist. ivtv: Autodetected WinTV PVR 150 card ivtv: Found an iTVC16 based chip ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 18 (level, low) -> IRQ 18 ivtv: Unreasonably low latency timer, setting to 64 (was 32) tveeprom: Hauppauge: model = 26559, rev = B260, serial# = 7678759 tveeprom: tuner = LG S001D MK3 (idx = 60, type = 58) tveeprom: tuner fmt = PAL(B/G) PAL(I) SECAM(L/L) PAL(D/K) (eeprom = 0x74, v4l2 = 0x00400e17) tveeprom: audio_processor = MSP3410D (type = 5) ivtv: i2c attach [client=tveeprom[50],ok] ivtv: Tuner Type 58, Tuner formats 0x00400e17, Radio: yes, Model 0x00892590, Revision 0x00000001 ivtv: PAL tuner detected ivtv: Radio detected tuner: Ignoring new-style parameters in presence of obsolete ones tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 ivtv: i2c attach [client=(tuner unset),ok] cx25840: starting probe on adapter ivtv i2c driver #0 (0x10005) cx25840: detecting cx25840 client on address 0x88 cx25840: cx25843-23 found. Initializing... cx25840: requesting /lib/modules/HcwMakoA.ROM cx25840: firmware loaded ivtv: i2c attach [client=cx25840[50],ok] ivtv: i2c attach [client=wm8775[50],ok] tda9885/6/7: chip found @ 0x86 ivtv: i2c attach [client=tda9887,ok] ivtv: Encoder revision: 0x02050032 ivtv: Encoder Firmware can be buggy, use version 0x02040011!!!! ivtv: Configuring WinTV PVR 150 card with 5 streams ivtv: Registered v4l2 device for encoder MPEG minor 0 ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total) ivtv: Registered v4l2 device for encoder YUV minor 32 ivtv: Create DMA encoder YUV stream: 0 x 12960 buffers (0KB total) ivtv: Registered v4l2 device for encoder VBI minor 224 ivtv: Create DMA encoder VBI stream: 0 x 12740 buffers (0KB total) ivtv: Registered v4l2 device for encoder PCM audio minor 24 ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total) ivtv: Registered v4l2 device for encoder radio minor 64 ivtv: Create encoder radio stream ivtv: Setting Tuner 58 tuner: type set to 58 (LG PAL TAPE-S001D) by ivtv i2c driver #0 cx25840: decoder set norm PAL ivtv: ivtv_enc_thread: pid = 7236, itv = 0xdebf3c60 ivtv: ivtv_enc_vbi_thread: pid = 7237, itv = 0xdebf3c60 cx25840: decoder set input (6) cx25840: now setting Tuner input cx25840: set audio input (0) ivtv: Switching standard to PAL. cx25840: decoder set norm PAL cx25840: decoder disable output cx25840: decoder enable output cx25840: decoder set norm PAL cx25840: decoder set input (6) cx25840: now setting Tuner input cx25840: set audio input (0) ivtv: Initialized WinTV PVR 150, card #0 ivtv: ==================== END INIT IVTV ==================== And finally: ivtv: ENC: REG_DMAXFER 2 wait failed Kind regards, Henk. ------------------------------------------------------- SF.Net email is Sponsored by the Better Software Conference & EXPO September 19-22, 2005 * San Francisco, CA * Development Lifecycle Practices Agile & Plan-Driven Development * Managing Projects & Teams * Testing & QA Security * Process Improvement & Measurement * http://www.sqe.com/bsce5sf _______________________________________________ ivtv-devel mailing list ivtv-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/ivtv-devel
