Bonk.. Does anyone have any possible help for me on this? I'm really stuck. Is there anything I should try? Thanks! Paul
On Thursday 08 September 2005 10:18 pm, Paul V. Gratz wrote: > Hi, > I have a myth box that has been happily running with an old winTV go > card for about a year or so and recently I picked up a pvr-500 as an > upgrade. I've taken the old wintv card out so I only have the pvr-500 in > the system. I've installed the ivtv 0.3.7k drivers and I'm running the > gentoo 2.6.12-r9 kernel with all the i2c stuff compiled in as part of the > kernel (is this a problem?). When I modprobe the ivtv driver and then try > to cat /dev/video0 > tmp.mpg the file size stays 0. Following the > instructions on the wiki I downloaded and installed the > pvr48wdm_1.8.22037.exe version of the firmware and have used the > ivtvfwextract.pl script to extract the .rom files and place them in > /lib/modules/. Here is my modules.conf: > > ----- > alias char-major-81 videodev > alias char-major-81-0 ivtv > alias char-major-81-1 ivtv > options ivtv ivtv_std=1 tuner=57,57 ivtv_debug=1 > options cx25840 debug=1 > options saa7127 > options msp3400 once=1 simple=1 > ----- > > (I've tried a number of variations but none seem to work for me) > > Here are the messages from dmesg when I modprobe ivtv: > > ------ > Linux video capture interface: v1.00 > ivtv: ==================== START INIT IVTV ==================== > ivtv: version 0.3.7 (k) loading > ivtv: Linux version: 2.6.12-gentoo-r9 SMP preempt PENTIUM4 gcc-3.3 > ivtv: In case of problems please include the debug info > ivtv: between the START INIT IVTV and END INIT IVTV lines when > ivtv: mailing the ivtv-devel mailinglist. > ivtv: Autodetected WinTV PVR 150 card (iTVC16 based) > ACPI: PCI Interrupt 0000:03:08.0[A] -> GSI 22 (level, low) -> IRQ 22 > tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 7967223 > tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57) > tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) > tveeprom: audio processor = CX25843 (type = 25) > tveeprom: decoder processor = CX25843 (type = 1e) > ivtv: i2c attach to card #0 ok [client=tveeprom[50], addr=50] > ivtv: This is the first unit of a PVR500 > ivtv: i2c attach to card #0 ok [client=(tuner unset), addr=60] > tuner 2-0060: chip found @ 0xc0 (ivtv i2c driver #0) > cx25840 debug: Module init > cx25840 debug: starting probe on adapter ivtv i2c driver #0 (0x10005) > ivtv warning: i2c client addr: 0x44 not found for command 0x800464cb! > ivtv: Failed to load module wm8775 > ivtv: Encoder revision: 0x02040011 > ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total) > ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total) > ivtv: Create DMA encoder VBI stream: 0 x 17472 buffers (0KB total) > ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total) > tuner 2-0060: type set to 57 (Philips FQ1236A MK4) > ivtv warning: i2c client addr: 0x44 not found for command 0x40046403! > ivtv warning: i2c client addr: 0x44 not found for command 0x40046404! > ivtv warning: i2c client addr: 0x1b not found for command 0x40047767! > ivtv warning: i2c client addr: 0x44 not found for command 0x4004646e! > ivtv warning: i2c client addr: 0x44 not found for command 0x40046403! > ivtv warning: i2c client addr: 0x44 not found for command 0x40046406! > ivtv warning: i2c client addr: 0x44 not found for command 0x40046406! > ivtv: Initialized WinTV PVR 150, card #0 > ivtv: ====================== NEXT CARD ====================== > ivtv: Autodetected WinTV PVR 150 card (iTVC16 based) > ACPI: PCI Interrupt 0000:03:09.0[A] -> GSI 23 (level, low) -> IRQ 23 > tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 7967223 > tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57) > tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) > tveeprom: audio processor = CX25843 (type = 25) > tveeprom: decoder processor = CX25843 (type = 1e) > ivtv: i2c attach to card #1 ok [client=tveeprom[50], addr=50] > ivtv: i2c attach to card #1 ok [client=(tuner unset), addr=61] > tuner 3-0061: chip found @ 0xc2 (ivtv i2c driver #1) > cx25840 debug: starting probe on adapter ivtv i2c driver #1 (0x10005) > ivtv: This is the second unit of a PVR500 > ivtv: Correcting tveeprom data: no radio present on second tuner > ivtv warning: i2c client addr: 0x44 not found for command 0x800464cb! > ivtv: Failed to load module wm8775 > ivtv: Encoder revision: 0x02040011 > ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total) > ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total) > ivtv: Create DMA encoder VBI stream: 0 x 17472 buffers (0KB total) > ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total) > tuner 3-0061: type set to 57 (Philips FQ1236A MK4) > ivtv warning: i2c client addr: 0x44 not found for command 0x40046403! > ivtv warning: i2c client addr: 0x44 not found for command 0x40046404! > ivtv warning: i2c client addr: 0x1b not found for command 0x40047767! > ivtv warning: i2c client addr: 0x44 not found for command 0x4004646e! > ivtv warning: i2c client addr: 0x44 not found for command 0x40046403! > ivtv warning: i2c client addr: 0x44 not found for command 0x40046406! > ivtv warning: i2c client addr: 0x44 not found for command 0x40046406! > ivtv: Initialized WinTV PVR 150, card #1 > ivtv: ==================== END INIT IVTV ==================== > > ------ > > When I try to cat /dev/video0 >tmp.mpg I get a zero sized file and the > following entries show up in dmesg: > > ivtv: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) > ivtv warning: i2c client addr: 0x44 not found for command 0x401c6466! > ivtv warning: i2c client addr: 0x44 not found for command 0x40046406! > ivtv warning: i2c client addr: 0x44 not found for command 0x40046406! > > > I've been searching around the web and various mailing lists all night but > I haven't been able to reach a conclusion on what is up. Do any of you all > think you could help me? > > Thanks! > Paul
pgpM1U5BBYv8z.pgp
Description: PGP signature
