On 1/18/06, Scott Reynolds <[EMAIL PROTECTED]> wrote: > This is very likely to be the problem: > > On Jan 18, 2006, at 4:08 AM, Viljo Viitanen wrote: > > > ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) > > ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes) > > ivtv0: Encoder revision: 0x02040024 > > ivtv0 warning: Encoder Firmware can be buggy, use version 0x02040011 > > or 0x02050032. > > ivtv0: Decoder revision: 0x02020023 > > My experience is that ivtv 0.3.9 and later work best with encoder > firmware 0x02050032.
Thanks for the hint, but it didn't help :/ I still get the same i2c warnings when loading the module and when trying to access /dev/video: ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.4.2 (tagged release) loading ivtv: Linux version: 2.6.15-1.1823_FC4 686 REGPARM 4KSTACKS gcc-4.0 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected WinTV PVR 350 card (cx23415 based) PCI: Found IRQ 11 for device 0000:01:09.0 PCI: Sharing IRQ 11 with 0000:01:0d.0 ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50] tveeprom 1-0050: Hauppauge model 48134, rev J342, serial# 7068133 tveeprom 1-0050: tuner model is Temic 4009FR5 (idx 42, type 20) tveeprom 1-0050: TV standards PAL(B/G) (eeprom 0x04) tveeprom 1-0050: audio processor is MSP4418 (idx 25) tveeprom 1-0050: decoder processor is SAA7115 (idx 19) tveeprom 1-0050: has radio, has IR remote tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61] ivtv0 warning: i2c client addr: 0x21 not found for command 0x8004646b! saa7127 1-0044: saa7127 found @ 0x88 (ivtv i2c driver #0) ivtv0: i2c attach to card #0 ok [client=saa7127, addr=44] msp3400 1-0040: chip=MSP4418G-A2 +nicam +simple +simpler +radio mode=simpler ivtv0: i2c attach to card #0 ok [client=MSP4418G-A2, addr=40] msp3400 1-0040: msp34xxg daemon started ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes) ivtv0: Encoder revision: 0x02050032 ivtv0: Decoder revision: 0x02020023 ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) ivtv0: Create encoder radio stream ivtv0: Allocate DMA decoder MPEG stream: 16 x 65536 buffers (1024KB total) ivtv0: Allocate DMA decoder VBI stream: 512 x 2048 buffers (1024KB total) ivtv0: Create decoder VOUT stream ivtv0: Allocate DMA decoder YUV stream: 20 x 51840 buffers (1024KB total) ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 bytes) tuner 1-0061: type set to 20 (Temic PAL_BG (4009 FR5) or PAL_I (4069 FR5)) ivtv0 warning: i2c client addr: 0x21 not found for command 0x40085618! ivtv0 warning: i2c client addr: 0x21 not found for command 0xc0045627! ivtv0 warning: i2c client addr: 0x21 not found for command 0x40085618! spurious 8259A interrupt: IRQ7. ivtv0 warning: i2c client addr: 0x21 not found for command 0x40045613! ivtv0 warning: i2c client addr: 0x21 not found for command 0x40045612! ivtv0: Initialized WinTV PVR 350, card #0 ivtv: ==================== END INIT IVTV ==================== (cat -v /dev/video) ivtv0 warning: i2c client addr: 0x21 not found for command 0xc0cc5605! ivtv0 warning: i2c client addr: 0x21 not found for command 0x40045613! ivtv0 warning: i2c client addr: 0x21 not found for command 0x40045612! -- Viljo Viitanen [EMAIL PROTECTED] _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
