I'm no expert, but it seems in all other ivtv dmesg output i've seen there is more info on it attaching to the tuner module...yours seems to be missing that info, perhaps thats why its not recognizing the 0x40 commands, they are meant for the tuner which it is not seeing?
my own ivtv dmesg out has lines like these: (but then again my myth box is broken at the moment, so take it with a grain of salt :) tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61] <snip> tuner 1-0061: type set to 21 (Temic NTSC (4039 FR5)) that last "tuner 1-0061" line above is exactly where your 0x40 errors start in my output...I don't know what your problem could be, but you might want to focus on the tuner module. Good luck. John Sutherland wrote: > I've googled, I've read the howto, and the troubleshooting sections.. > Nothing seems to work.. > > I have a pvr350, running on via epia MII 10000, running gentoo.. > (kernel 2.6.14gentoo-r5) I had everything working up until I upgraded > ivtv (from 0.3.x something).. The 0.4.2 version I'm running now will > not record sound.. > > My current setup is using the S-video and Line-in on the 350.. This > is only a mythtv server, so no framebuffer.. I do a "cat /dev/video0 > > file.mpg", and I get video, but no sound.. I can't test to /dev/ > video16, since I don't have the cable for it anymore.... > > lsmod: > > video ~ # lsmod > Module Size Used by > snd_via82xx 22688 0 > snd_ac97_codec 91400 1 snd_via82xx > snd_ac97_bus 1760 1 snd_ac97_codec > snd_mpu401_uart 6112 1 snd_via82xx > snd_rawmidi 20736 1 snd_mpu401_uart > tda9887 14320 0 > msp3400 32608 0 > saa7127 11412 0 > saa7115 14928 0 > tuner 22848 0 > tveeprom 12268 0 > ivtv 214548 0 > firmware_class 7904 1 ivtv > videodev 7296 1 ivtv > > No options set in modules.conf..... > > One thing I noticed is that I can't set the volume: > > video ~ # ivtvctl -Y > ioctl: VIDIOC_QUERYCTRL > Brightness = 127 > Contrast = 63 > Saturation = 63 > Hue = 0 > Volume = 0 > Mute = 0 > video ~ # ivtvctl -y volume=65000 > ioctl VIDIOC_S_CTRL ok > video ~ # ivtvctl -Y > ioctl: VIDIOC_QUERYCTRL > Brightness = 127 > Contrast = 63 > Saturation = 63 > Hue = 0 > Volume = 0 > Mute = 0 > > Maybe thats a clue? > > Here's the dmesg stuff: > > ivtv: ==================== START INIT IVTV ==================== > ivtv: version 0.4.2 (tagged release) loading > ivtv: Linux version: 2.6.14-gentoo-r5 preempt VIAC3-2 gcc-3.4 > ivtv: In case of problems please include the debug info between > ivtv: the START INIT IVTV and END INIT IVTV lines, along with > ivtv: any module options, when mailing the ivtv-users mailinglist. > ivtv0: Autodetected WinTV PVR 350 card (cx23415 based) > PCI: Found IRQ 5 for device 0000:00:14.0 > PCI: Sharing IRQ 5 with 0000:00:0a.1 > PCI: Sharing IRQ 5 with 0000:00:0d.0 > ivtv0: Unreasonably low latency timer, setting to 64 (was 32) > tveeprom: ivtv version > tveeprom: Hauppauge: model = 48132, rev = J323, serial# = 7065327 > tveeprom: tuner = Philips FM1236 (idx = 23, type = 2) > tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) > tveeprom: audio processor = MSP4448 (type = 1b) > tveeprom: decoder processor = SAA7115 (type = 13) > ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50] > saa7115 1-0021: ivtv driver > saa7115 1-0021: saa7115 found @ 0x42 (ivtv i2c driver #0) > ivtv0: i2c attach to card #0 ok [client=saa7115, addr=21] > saa7127 1-0044: ivtv driver > saa7127 1-0044: saa7127 found @ 0x88 (ivtv i2c driver #0) > ivtv0: i2c attach to card #0 ok [client=saa7127, addr=44] > ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) > ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes) > ivtv0: Encoder revision: 0x02050032 > ivtv0: Decoder revision: 0x02020023 > ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB > total) > ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB > total) > ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB > total) > ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers > (2048KB total) > ivtv0: Create encoder radio stream > ivtv0: Allocate DMA decoder MPEG stream: 16 x 65536 buffers (1024KB > total) > ivtv0: Allocate DMA decoder VBI stream: 512 x 2048 buffers (1024KB > total) > ivtv0: Create decoder VOUT stream > ivtv0: Allocate DMA decoder YUV stream: 24 x 43200 buffers (1024KB > total) > ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 bytes) > ivtv0 warning: i2c client addr: 0x00 not found for command 0x40045403! > ivtv0 warning: i2c client addr: 0x40 not found for command 0x40086d11! > ivtv0 warning: i2c client addr: 0x40 not found for command 0x80287610! > ivtv0 warning: i2c client addr: 0x40 not found for command 0x40287611! > ivtv0 warning: i2c client addr: 0x00 not found for command 0x40085618! > ivtv0 warning: i2c client addr: 0x40 not found for command 0x40085618! > ivtv0 warning: i2c client addr: 0x40 not found for command 0x80287610! > ivtv0 warning: i2c client addr: 0x40 not found for command 0x40287611! > ivtv0 warning: i2c client addr: 0x00 not found for command 0x402c5639! > ivtv0 warning: i2c client addr: 0x40 not found for command 0x402c5639! > ivtv0 warning: i2c client addr: 0x40 not found for command 0x80287610! > ivtv0 warning: i2c client addr: 0x40 not found for command 0x40287611! > ivtv0: Initialized WinTV PVR 350, card #0 > ivtv: ==================== END INIT IVTV ==================== > > > I also get more of the 0x40 not found's after that... > > Any ideas? > > --John > > _______________________________________________ > ivtv-users mailing list > [email protected] > http://ivtvdriver.org/mailman/listinfo/ivtv-users > _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
