John McCarthy wrote:
> Hi Kirk,
>
> Hmm, can you send your
> Xorg.0.log, /etc/modprobe.conf, /etc/X11/xorg.conf, and the IVTV startup
> from /var/log/messages? Maybe I can spot something. Did you try
> 'mplayer -vo xv' as well to see if it gives any better error messages?
Executing 'mplayer -vo xv dvd://' yields:
vo: X11 running at 720x480 with depth 24 and 32 bpp (":0.0" => local display)It
seems
there is no Xvideo support for your video card available.
> On my Fedora Core 4 + ATrpms MythTV box I've got the following ivtv
> RPMs:
I'm running CentOS 4.2 (RHEL4) X86_64 on an Intel P4 521. The motherboard I
picked
somehow refuses to boot i386 which would have been my first choice.
I am running kernel 2.6.14.6 in uniprocessor mode and thus compiling ivtv from
source.
I just installed a PVR-500 in addition to the PVR-350. I am running the ivtv
0.4.3
development snapshot downloaded last night. I thought the development snapshot
was a
fix for getting the PVR-500 to work. But now I think the problem was a
workaround for
a non-MPEG tuner I previously had installed. Probably removing that workaround
would
allow 0.4.2 to work but now that it's working with 0.4.3... well...
> Hmm, one thought, I see your ivtvdev_drv is for Xserver 4.3.99.902. Is
> that the version of Xserver you are running (check rpm pkg, xorg.0.log
> or xdpyinfo output). If not you should get an ivtvdev_drv built for at
> least the first 2 or 3 version numbers (e.g. 4.3 above). Going by your
> log output I suspect that should be an Xorg version (6.X) not XFree86
> (4.X). My FC4 has xorg-x11-6.8.2-37.FC4.49.2_4.rhfc4.at which is an
> Xorg 6.8.2 Xserver.
I am using the distro's packages for xorg: xorg-x11-6.8.2-1.EL.13.20. Looking
through
/var/log/Xorg.0.log I don't see any 'Xserver' version numbers, just the 6.8.2
version
number.
> I also see you are using the framebuffer driver--is it possible to use
> the 350's output without the fb driver? If so it might be worth a try.
Not sure how to do this. I thought the 'Option "fbdev" "/dev/fb0"' in xorg.conf
is
required to use the 350 for video out?
> I also see by the lib64 that you have a 64-bit system. Is that correct?
> If so make sure you have 64-bit compatible drivers.
Everything is either compiled from source or x86_64 packages from atrpms.
The modprobe.conf and ivtv boot messages are below.
Thanks for your help.
Kirk
===================================
modprobe.conf (in part):
alias char-major-81 videodev
alias char-major-81-0 ivtv
alias char-major-81-1 ivtv
alias char-major-81-2 ivtv
options tuner debug=1
# I2C module options
alias char-major-89 i2c-dev
#lirc module
#Depends on ivtv module
alias char-major-61 lirc_i2c
install lirc_i2c /sbin/modprobe ivtv; /sbin/modprobe --ignore-install lirc_i2c
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.4.3 (development snapshot compiled on Wed 25 Jan 2006 08:36:25
PM
PST) loading
ivtv: Linux version: 2.6.14.6-up-wcpvr01 gcc-3.4
ivtv: In case of problems please include the debug info between
ivtv: the START INIT IVTV and END INIT IVTV lines, along with
ivtv: any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected WinTV PVR 350 card (cx23415 based)
ACPI: PCI Interrupt 0000:01:02.0[A] -> GSI 17 (level, low) -> IRQ 185
ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
tveeprom: The eeprom says no radio is present, but the tuner type 68
tveeprom: indicates otherwise. I will assume that radio is present.
tveeprom: ivtv version
tveeprom: Hauppauge: model = 48132, rev = K268, serial# = 2985761
tveeprom: tuner = LG TAPE H001F MK3 (idx = 68, type = 47)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio processor = MSP4448 (type = 1b)
tveeprom: decoder processor = SAA7115 (type = 13)
ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61]
saa7115 0-0021: ivtv driver
saa7115 0-0021: saa7115 found @ 0x42 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=saa7115, addr=21]
saa7127 0-0044: ivtv driver
saa7127 0-0044: saa7129 found @ 0x88 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=saa7127, addr=44]
msp3400 0-0040: ivtv driver
msp3400 0-0040: chip=MSP4448G-A2 +nicam +simple +simpler +radio mode=simpler
ivtv0: i2c attach to card #0 ok [client=MSP4448G-A2, addr=40]
msp3400 0-0040: msp34xxg daemon started
tda9887 0-0043: (ivtv) chip found @ 0x86 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43]
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes)
ivtv0: Encoder revision: 0x02050032
ivtv0: Decoder revision: 0x02020023
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
ivtv0: Create encoder radio stream
ivtv0: Allocate DMA decoder MPEG stream: 16 x 65536 buffers (1024KB total)
ivtv0: Allocate DMA decoder VBI stream: 512 x 2048 buffers (1024KB total)
ivtv0: Create decoder VOUT stream
ivtv0: Allocate DMA decoder YUV stream: 24 x 43200 buffers (1024KB total)
ivtv0: unable to open firmware v4l-cx2341x-init.mpg
ivtv0: did you put the firmware in the hotplug firmware directory?
ivtv0: failed to read mpeg decoder initialisation file v4l-cx2341x-init.mpg
tuner: type set to 47 (LG NTSC (TAPE series)) by ivtv i2c driver #0
tuner: switching to v4l2
tuner: tv freq set to 67.25
tuner: tv 0x07 0x10 0x8e 0x01
ivtv0: Initialized WinTV PVR 350, card #0
ivtv: ====================== NEXT CARD ======================
ivtv1: Autodetected WinTV PVR 150 card (cx23416 based)
ACPI: PCI Interrupt 0000:02:08.0[A] -> GSI 22 (level, low) -> IRQ 193
ivtv1: Unreasonably low latency timer, setting to 64 (was 32)
tveeprom: Second (radio) tuner idx 101
tveeprom: ivtv version
tveeprom: Hauppauge: model = 23552, rev = D487, serial# = 8921592
tveeprom: tuner = Samsung TCPN 2121P30A (idx = 87, type = 68)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio processor = CX25843 (type = 25)
tveeprom: decoder processor = CX25843 (type = 1e)
ivtv1: i2c attach to card #1 ok [client=tveeprom, addr=50]
tuner (ivtv): chip found at addr 0xc0 i2c-bus ivtv i2c driver #1
TEA5767 detected.
ivtv1: i2c attach to card #1 ok [client=(tuner unset), addr=60]
tuner: type set to 62 (Philips TEA5767HN FM Radio) by autodetect
type set to 62 (Philips TEA5767HN FM Radio)
tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #1
ivtv1: i2c attach to card #1 ok [client=(tuner unset), addr=61]
ivtv1: This is the first unit of a PVR500
cx25840 1-0044: ivtv driver
cx25840 1-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #1)
cx25840 1-0044: loaded v4l-cx25840.fw firmware (14264 bytes)
ivtv1: i2c attach to card #1 ok [client=cx25840, addr=44]
wm8775 1-001b: ivtv driver
wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #1)
ivtv1: i2c attach to card #1 ok [client=wm8775, addr=1b]
ivtv1: Detected a TEA5767 radio tuner. Enabling radio support.
ivtv1: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv1: Encoder revision: 0x02050032
ivtv1: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv1: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv1: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv1: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
ivtv1: Create encoder radio stream
tuner: type set to 68 (Samsung TCPN 2121P30A) by ivtv i2c driver #1
tuner: switching to v4l2
tuner: tv freq set to 67.25
tuner: tv 0x07 0x10 0xce 0x01
ivtv1: Initialized WinTV PVR 500 (unit #1), card #1
ivtv: ====================== NEXT CARD ======================
ivtv2: Autodetected WinTV PVR 150 card (cx23416 based)
ACPI: PCI Interrupt 0000:02:09.0[A] -> GSI 21 (level, low) -> IRQ 201
ivtv2: Unreasonably low latency timer, setting to 64 (was 32)
tveeprom: Second (radio) tuner idx 101
tveeprom: ivtv version
tveeprom: Hauppauge: model = 23552, rev = D487, serial# = 8921592
tveeprom: tuner = Samsung TCPN 2121P30A (idx = 87, type = 68)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio processor = CX25843 (type = 25)
tveeprom: decoder processor = CX25843 (type = 1e)
ivtv2: i2c attach to card #2 ok [client=tveeprom, addr=50]
tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #2
ivtv2: i2c attach to card #2 ok [client=(tuner unset), addr=61]
cx25840 2-0044: ivtv driver
cx25840 2-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #2)
cx25840 2-0044: loaded v4l-cx25840.fw firmware (14264 bytes)
ivtv2: i2c attach to card #2 ok [client=cx25840, addr=44]
wm8775 2-001b: ivtv driver
wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #2)
ivtv2: i2c attach to card #2 ok [client=wm8775, addr=1b]
ivtv2: This is the second unit of a PVR500
ivtv2: Correcting tveeprom data: no radio present on second unit
ivtv2: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv2: Encoder revision: 0x02050032
ivtv2: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv2: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv2: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv2: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
tuner: type set to 68 (Samsung TCPN 2121P30A) by ivtv i2c driver #2
tuner: switching to v4l2
tuner: tv freq set to 67.25
tuner: tv 0x07 0x10 0xce 0x01
ivtv2: Initialized WinTV PVR 500 (unit #2), card #2
ivtv: ==================== END INIT IVTV ====================
_______________________________________________
ivtv-users mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-users
