I have recently upgraded to FC 2.6.15-1.1830_FC4 Would this have anything to do with;
tveeprom: disagrees about version of symbol struct_module saa7115: disagrees about version of symbol struct_module tda9887: disagrees about version of symbol struct_module ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.4.2 (tagged release) loading ivtv: Linux version: 2.6.15-1.1830_FC4 686 REGPARM 4KSTACKS gcc-4.0 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected WinTV PVR 250 card (cx23416 based) PCI: Found IRQ 12 for device 0000:00:09.0 ivtv0: Unreasonably low latency timer, setting to 64 (was 32) tveeprom: disagrees about version of symbol struct_module ivtv0: Failed to load module tveeprom ivtv0 warning: i2c client addr: 0x50 not found for command 0x0! ivtv0: Error -19 reading Hauppauge eeprom. ivtv0: Possible causes: the tveeprom module was not loaded, or ivtv0: the eeprom kernel module was loaded before the tveeprom module. tuner: disagrees about version of symbol struct_module ivtv0: Failed to load module tuner saa7115: disagrees about version of symbol struct_module ivtv0: Failed to load module saa7115 ivtv0 warning: i2c client addr: 0x21 not found for command 0x8004646b! msp3400: disagrees about version of symbol struct_module ivtv0: Failed to load module msp3400 tda9887: disagrees about version of symbol struct_module ivtv0: Failed to load module tda9887 ivtv0: Could not detect tuner standard, defaulting to NTSC. ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv0: Encoder revision: 0x02050032 ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) ivtv0 warning: i2c client addr: 0x21 not found for command 0x40085618! ivtv0 warning: i2c client addr: 0x21 not found for command 0xc0045627! ivtv0 warning: i2c client addr: 0x40 not found for command 0x40086d11! ivtv0 warning: i2c client addr: 0x40 not found for command 0x80287610! ivtv0 warning: i2c client addr: 0x40 not found for command 0x40287611! ivtv0 warning: i2c client addr: 0x00 not found for command 0x40085618! ivtv0 warning: i2c client addr: 0x40 not found for command 0x40085618! ivtv0 warning: i2c client addr: 0x21 not found for command 0x40085618! ivtv0 warning: i2c client addr: 0x40 not found for command 0x80287610! ivtv0 warning: i2c client addr: 0x40 not found for command 0x40287611! ivtv0 warning: i2c client addr: 0x21 not found for command 0x40045613! ivtv0 warning: i2c client addr: 0x00 not found for command 0x402c5639! ivtv0 warning: i2c client addr: 0x40 not found for command 0x402c5639! ivtv0 warning: i2c client addr: 0x21 not found for command 0x40045612! ivtv0 warning: i2c client addr: 0x40 not found for command 0x80287610! ivtv0 warning: i2c client addr: 0x40 not found for command 0x40287611! ivtv0: Initialized WinTV PVR 250, card #0 ivtv: ==================== END INIT IVTV ==================== Mik _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
