I believe I have the 0.4.3 ivtv driver loading
successfully. I'm able to display the test image and
capture from /dev/video0, but when I try passthrough
mode:
# ivtvctl -K 1
ioctl IVTV_IOC_PASSTHROUGH ok
all I get is a black screen in the PVR-350 video out.
Last time I posted on this subject, one of the users
suggested that I do
# cat test.mpg > /dev/video16
This also results in a black screen. Does this mean
that I won't be able to watch live TV when I install
MythTV? I'm capturing from composite input 0 and I'm
on FC4, if that makes any difference.
Thanks in advance,
Boris
------------
modprobe.conf:
alias eth0 via-rhine
alias snd-card-0 snd-via82xx
options snd-card-0 index=0
options snd-via82xx index=0
remove snd-via82xx { /usr/sbin/alsactl store 0
>/dev/null 2>&1 || : ; }; /sbin/modprobe -r
--ignore-remove snd-via82xx
alias usb-controller ehci-hcd
alias usb-controller1 uhci-hcd
# ivtv
install ivtv /sbin/modprobe --ignore-install ivtv;
/sbin/modprobe ivtv-fb
---------------------
dmesg output:
ivtv: ==================== START INIT IVTV
====================
ivtv: version 0.4.3 (development snapshot compiled on
Tue Feb 14 19:46:32 2006) loading
ivtv: Linux version: 2.6.15-1.1831_FC4 686 REGPARM
4KSTACKS gcc-4.0
ivtv: In case of problems please include the debug
info between
ivtv: the START INIT IVTV and END INIT IVTV lines,
along with
ivtv: any module options, when mailing the ivtv-users
mailinglist.
ivtv0: Autodetected WinTV PVR 350 card (cx23415 based)
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKD] ->
GSI 10 (level, low) -> IRQ 10
ivtv0: Unreasonably low latency timer, setting to 64
(was 32)
tveeprom: ivtv version
tveeprom: Hauppauge: model = 48132, rev = K268,
serial# = 2867223
tveeprom: tuner = LG TAPE H001F MK3 (idx = 68, type =
47)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 =
0x00001000)
tveeprom: audio processor = MSP4448 (type = 1b)
tveeprom: decoder processor = SAA7115 (type = 13)
ivtv0: i2c attach to card #0 ok [client=tveeprom,
addr=50]
tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c
driver #0
ivtv0: i2c attach to card #0 ok [client=(tuner unset),
addr=61]
saa7115 1-0021: saa7115 found @ 0x42 (ivtv i2c driver
#0)
ivtv0: i2c attach to card #0 ok [client=saa7115,
addr=21]
saa7127 1-0044: saa7129 found @ 0x88 (ivtv i2c driver
#0)
ivtv0: i2c attach to card #0 ok [client=saa7127,
addr=44]
msp3400 1-0040: chip=MSP4448G-A2 +nicam +simple
+simpler +radio mode=simpler
ivtv0: i2c attach to card #0 ok [client=MSP4448G-A2,
addr=40]
msp3400 1-0040: msp34xxg daemon started
tda9887 1-0043: (ivtv) chip found @ 0x86 (ivtv i2c
driver #0)
ivtv0: i2c attach to card #0 ok [client=tda9887,
addr=43]
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144
bytes)
ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144
bytes)
ivtv0: Encoder revision: 0x02050032
ivtv0: Decoder revision: 0x02020023
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768
buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 194 x 10800
buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 120 x 17472
buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x
4608 buffers (2048KB total)
ivtv0: Create encoder radio stream
ivtv0: Allocate DMA decoder MPEG stream: 16 x 65536
buffers (1024KB total)
ivtv0: Allocate DMA decoder VBI stream: 512 x 2048
buffers (1024KB total)
ivtv0: Create decoder VOUT stream
ivtv0: Allocate DMA decoder YUV stream: 24 x 43200
buffers (1024KB total)
ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648
bytes)
tuner: type set to 47 (LG NTSC (TAPE series)) by ivtv
i2c driver #0
ivtv0: Initialized WinTV PVR 350, card #0
ivtv: ==================== END INIT IVTV
====================
__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com
_______________________________________________
ivtv-users mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-users
