I am running FC3 and just updated my kernel to 2.6.12-1.1381_FC3 using atrpms via yum. I then also updated ivtv to the latest of 0.4.3.
Now I can't tune any channels on my PVR-150, using ivtv-tune. I have tried all inputs and different channels and the same results each time of static with sound (static sound). All testing was done using the #cat /dev/video0 /tmp/test.mpg - method. I also have a PVR-250 which I can change channels using ivtv-tune and I get a picture. I don't get any sound out of the pvr-250. I tried adjusting the audio inputs which didn't help. I tried playing with the msp3400.ko, but wasn't sure what to do with it. My latest working setup was kernel 2.6.11-1.35_FC3 and ivtv 0.3.7d?? Any help or advice would be appreciated. Thanks, Adam $rpm -qa '*ivtv*' returns this: ----------------------- ivtv-firmware-enc-2.04.024-8.at ivtv-firmware-audio-0.0.1-5.at ivtv-0.4.3-103.rhfc3.at perl-Video-ivtv-0.13-7.rhfc3.at ivtv-kmdl-2.6.12-1.1381_FC3-0.4.3-103.rhfc3.at ivtv-firmware-dec-2.02.023-8.at ====================== Here is my ivtv part of Modprobe.conf: ---------------- alias char-major-81 videodev alias char-major-81-0 ivtv alias char-major-81-1 ivtv I tried adding these but no help: alias tveeprom tveeprom-ivtv alias msp3400 msp3400-ivtv alias tuner tuner-ivtv ================== Here is what dmesg gives: ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.4.3 (tagged release) loading ivtv: Linux version: 2.6.12-1.1381_FC3 686 REGPARM 4KSTACKS gcc-3.4 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected WinTV PVR 150 card (cx23416 based) ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 11 ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [LNK1] -> GSI 11 (level, low) -> IRQ 11 ivtv0: Unreasonably low latency timer, setting to 64 (was 32) ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50] tveeprom: Hauppauge: model = 26032, rev = C199, serial# = 8002882 tveeprom: tuner = <unknown> (idx = 99, type = -1069826176) tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) tveeprom: audio_processor = TDA9850 (type = 3) ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61] tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #0) cx25840 2-0044: ivtv driver cx25840 2-0044: cx25841-23 found @ 0x88 (ivtv i2c driver #0) cx25840 2-0044: loaded v4l-cx25840.fw firmware (13353 bytes) ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44] wm8775 2-001b: ivtv driver wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #0) ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b] ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv0: Encoder revision: 0x02040024 ivtv0 warning: Encoder Firmware can be buggy, use version 0x02040011 or 0x02050032. ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) ivtv0: Create encoder radio stream tuner 2-0061: tuner type not set ivtv0: Initialized WinTV PVR 150, card #0 ivtv: ====================== NEXT CARD ====================== ivtv1: Autodetected WinTV PVR 250 card (cx23416 based) ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 3 ACPI: PCI Interrupt 0000:01:0a.0[A] -> Link [LNK3] -> GSI 3 (level, low) -> IRQ 3 ivtv1: Unreasonably low latency timer, setting to 64 (was 32) ivtv1: i2c attach to card #1 ok [client=tveeprom, addr=50] ivtv1: i2c attach to card #1 ok [client=(tuner unset), addr=61] tuner 3-0061: chip found @ 0xc2 (ivtv i2c driver #1) tveeprom: Hauppauge: model = 32062, rev = B185, serial# = 7478082 tveeprom: tuner = TCL 2002N 6A (idx = 85, type = 50) tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) tveeprom: audio_processor = MSP3445 (type = 12) saa7115 3-0021: ivtv driver saa7115 3-0021: saa7115 found @ 0x42 (ivtv i2c driver #1) ivtv1: i2c attach to card #1 ok [client=saa7115, addr=21] msp34xx: init: chip=MSP3445G-B8 +nicam +simple +simpler +radio mode=simpler ivtv1: i2c attach to card #1 ok [client=MSP3445G-B8, addr=40] msp34xxg: daemon started ivtv1: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv1: Encoder revision: 0x02040024 ivtv1 warning: Encoder Firmware can be buggy, use version 0x02040011 or 0x02050032. ivtv1: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv1: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv1: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) ivtv1: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) ivtv1: Create encoder radio stream tuner 3-0061: type set to 50 (TCL 2002N) ivtv1: Initialized WinTV PVR 250, card #1 ivtv: ==================== END INIT IVTV ==================== _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
