Is anyone else experiencing this problem?
I'm running Knoppmyth R5B7 on an athlon 650 Mhz system with a PVR-500
MCE. I have upgraded ivtv to 0.4.4 and am still having problems. If I
specify a tuner (Options ivtv tuner=50,50) I get most* of the channels,
but if I don't I get the "type 4" tuner not loaded and only one channel
works (the last channel I watched before reboot).
*Channel breakdown
2-56 Good
57 Flickers
58-61 Pure Static
62+ Good
I have read that people we adding aliases to their modprobe.conf (or
/etc/modprobe.d/KnoppMyth in Knoppmyth) to get it working so I tried:
alias char-major-81-0 ivtv
alias char-major-81-1 ivtv
alias tveeprom tveeprom-ivtv
alias tuner tuner-ivtv
alias tda9887 tda9887-ivtv
alias msp3400 msp3400-ivtv
And just about every combination of the above. When I have tveeprom
aliased it recognizes the tuner as type 68, but then later gives me the
error "Failed to load module tuner"
Here is my init ivtv with (tuner,tveeprom...etc) aliased.
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.4.4 (tagged release) loading
ivtv: Linux version: 2.6.15-chw-2 SMP preempt 586 gcc-3.3
ivtv: In case of problems please include the debug info between
ivtv: the START INIT IVTV and END INIT IVTV lines, along with
ivtv: any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected WinTV PVR 150 card (cx23416 based)
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [LNKB] -> GSI 5 (level, low)
-> IRQ 5
ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
cx25840 1-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
eth0: no IPv6 routers present
cx25840 1-0044: loaded v4l-cx25840.fw firmware (14264 bytes)
ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44]
wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b]
tveeprom: Second (radio) tuner idx 101
tveeprom: ivtv version
tveeprom: Hauppauge: model = 23552, rev = E587, serial# = 8826077
tveeprom: tuner = Samsung TCPN 2121P30A (idx = 87, type = 68)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio processor = CX25843 (type = 25)
tveeprom: decoder processor = CX25843 (type = 1e)
ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
ivtv0: Failed to load module tveeprom
ivtv0: This is the first unit of a PVR500
ivtv0: Failed to load module tuner
ivtv0: Failed to load module tda9887
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv0: Encoder revision: 0x02050032
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB
total)
ivtv0: Create encoder radio stream
ivtv0 warning: i2c client addr: 0x00 not found for command 0x40045403!
ivtv0 warning: i2c client addr: 0x00 not found for command 0x40085618!
ivtv0 warning: i2c client addr: 0x00 not found for command 0x402c5639!
ivtv0: Initialized WinTV PVR 500 (unit #1), card #0
ivtv: ====================== NEXT CARD ======================
ivtv1: Autodetected WinTV PVR 150 card (cx23416 based)
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [LNKC] -> GSI 10 (level,
low) -> IRQ 10
ivtv1: Unreasonably low latency timer, setting to 64 (was 32)
cx25840 2-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #1)
cx25840 2-0044: loaded v4l-cx25840.fw firmware (14264 bytes)
ivtv1: i2c attach to card #1 ok [client=cx25840, addr=44]
wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #1)
ivtv1: i2c attach to card #1 ok [client=wm8775, addr=1b]
tveeprom: Second (radio) tuner idx 101
tveeprom: ivtv version
tveeprom: Hauppauge: model = 23552, rev = E587, serial# = 8826077
tveeprom: tuner = Samsung TCPN 2121P30A (idx = 87, type = 68)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio processor = CX25843 (type = 25)
tveeprom: decoder processor = CX25843 (type = 1e)
ivtv1: i2c attach to card #1 ok [client=tveeprom, addr=50]
ivtv1: Failed to load module tveeprom
ivtv1: This is the second unit of a PVR500
ivtv1: Correcting tveeprom data: no radio present on second unit
ivtv1: Failed to load module tuner
ivtv1: Failed to load module tda9887
ivtv1: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv1: Encoder revision: 0x02050032
ivtv1: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv1: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv1: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv1: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB
total)
ivtv1 warning: i2c client addr: 0x00 not found for command 0x40045403!
ivtv1 warning: i2c client addr: 0x00 not found for command 0x40085618!
ivtv1 warning: i2c client addr: 0x00 not found for command 0x402c5639!
ivtv1: Initialized WinTV PVR 500 (unit #2), card #1
ivtv: ==================== END INIT IVTV ====================
Here is my init ivtv without any ivtv aliases (Knoppmyth default)
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.4.4 (tagged release) loading
ivtv: Linux version: 2.6.15-chw-2 SMP preempt 586 gcc-3.3
ivtv: In case of problems please include the debug info between
ivtv: the START INIT IVTV and END INIT IVTV lines, along with
ivtv: any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected WinTV PVR 150 card (cx23416 based)
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [LNKB] -> GSI 5 (level, low)
-> IRQ 5
ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
tuner 1-0060: TEA5767 detected.
tuner 1-0060: chip found @ 0xc0 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=60]
tuner 1-0060: type set to 62 (Philips TEA5767HN FM Radio)
tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61]
cx25840 1-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
cx25840 1-0044: loaded v4l-cx25840.fw firmware (14264 bytes)
ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44]
wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b]
tveeprom 1-0050: Hauppauge model 23552, rev E587, serial# 8826077
tveeprom 1-0050: tuner model is Samsung TCPN 2121P30A (idx 87, type 4)
tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 1-0050: second tuner model is Philips TEA5768HL FM Radio (idx
101, type 62)
tveeprom 1-0050: audio processor is CX25843 (idx 37)
tveeprom 1-0050: decoder processor is CX25843 (idx 30)
tveeprom 1-0050: has radio, has no IR remote
ivtv0: This is the first unit of a PVR500
ivtv0: Detected a TEA5767 radio tuner. Enabling radio support.
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv0: Encoder revision: 0x02050032
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB
total)
ivtv0: Create encoder radio stream
tuner 1-0061: tuner type not set
tuner 1-0061: tuner type not set
ivtv0: Initialized WinTV PVR 500 (unit #1), card #0
ivtv: ====================== NEXT CARD ======================
ivtv1: Autodetected WinTV PVR 150 card (cx23416 based)
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [LNKC] -> GSI 10 (level,
low) -> IRQ 10
ivtv1: Unreasonably low latency timer, setting to 64 (was 32)
ivtv1: i2c attach to card #1 ok [client=tveeprom, addr=50]
tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #1)
ivtv1: i2c attach to card #1 ok [client=(tuner unset), addr=61]
cx25840 2-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #1)
cx25840 2-0044: loaded v4l-cx25840.fw firmware (14264 bytes)
ivtv1: i2c attach to card #1 ok [client=cx25840, addr=44]
wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #1)
ivtv1: i2c attach to card #1 ok [client=wm8775, addr=1b]
tveeprom 2-0050: Hauppauge model 23552, rev E587, serial# 8826077
tveeprom 2-0050: tuner model is Samsung TCPN 2121P30A (idx 87, type 4)
tveeprom 2-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 2-0050: second tuner model is Philips TEA5768HL FM Radio (idx
101, type 62)
tveeprom 2-0050: audio processor is CX25843 (idx 37)
tveeprom 2-0050: decoder processor is CX25843 (idx 30)
tveeprom 2-0050: has radio, has no IR remote
ivtv1: This is the second unit of a PVR500
ivtv1: Correcting tveeprom data: no radio present on second unit
ivtv1: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv1: Encoder revision: 0x02050032
ivtv1: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv1: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv1: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv1: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB
total)
tuner 2-0061: tuner type not set
tuner 2-0061: tuner type not set
ivtv1: Initialized WinTV PVR 500 (unit #2), card #1
ivtv: ==================== END INIT IVTV ====================
And for completeness sake here's the output of `lspci -vv`:
0000:02:08.0 Multimedia video controller: Internext Compression Inc
iTVC16 (CX23416) MPEG-2 Encoder (rev 01)
Subsystem: Hauppauge computer works Inc.: Unknown device e807
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (32000ns min, 2000ns max), Cache Line Size: 0x08 (32
bytes)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:02:09.0 Multimedia video controller: Internext Compression Inc
iTVC16 (CX23416) MPEG-2 Encoder (rev 01)
Subsystem: Hauppauge computer works Inc.: Unknown device e817
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (32000ns min, 2000ns max), Cache Line Size: 0x08 (32
bytes)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at e4000000 (32-bit, prefetchable) [size=64M]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Any help would be great. If I forgot to post any information let me
know and I will post it ASAP.
Thanks.
-UNOmar
_______________________________________________
ivtv-users mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-users
