option ivtv tuner=50
to my /etc/modules.conf
and now video works like a champ. Thanks to Hans for his suggestions.
thanks,
tom
On 6/8/06, Tom Stokoe <[EMAIL PROTECTED]> wrote:
The saga continues. . . As you'll recall, my ivtv drivers were freezing when the channel/input was being changed while the video stream was being read (ie. cat /dev/video0 > /dev/null). I decided to build my own 2.6.16.20 kernel (which was a minor nightmare since i kept forgeting to include the conexiant drivers for the encoder chip) this was rather poorly documented by the HOWTO and READMEs in the 0.6 ivtv version. Anywho, i installed 0.6, and am now getting the dreaded:
tuner 0-0061: tuner type not set
Both the input and channel can now be changed during a stream, but now i can't see any stations. It's classic white noise (video and audio). I did install Windoze and verified that the card is functioning properly there (which it is.) I feel the answer's within sight, but it's not quite there yet. Is it possible there's another kernel driver that i need that isn't getting loaded?
Here's the steaming new syslog:
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.6.2 (tagged release) loading
ivtv: Linux version: 2.6.16.20 PENTIUM4 gcc-3.3
ivtv: In case of problems please include the debug info between
ivtv: the START INIT IVTV and END INIT IVTV lines, along with
ivtv: any module options, when mailing the ivtv-users mailinglist.ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based)
ACPI: PCI Interrupt 0000:01:02.0[A] -> Link [LNKB] -> GSI 3 (level, low) -> IRQ 3tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0)
cx25840 0-0044: cx25841-23 found @ 0x88 (ivtv i2c driver #0)
cx25840 0-0044: loaded v4l-cx25840.fw firmware (14264 bytes)tveeprom 0-0050: Hauppauge model 26132, rev F0B2, serial# 9329517
tveeprom 0-0050: tuner model is TCL M2523_5N_E (idx 112, type 4)
tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 0-0050: audio processor is CX25841 (idx 35)
tveeprom 0-0050: decoder processor is CX25841 (idx 28)
tveeprom 0-0050: has no radio, has IR remote
wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0)ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv0: Encoder revision: 0x02050032
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)tuner 0-0061: tuner type not set
tuner 0-0061: tuner type not set
ivtv0: Initialized Hauppauge WinTV PVR-150, card #0
ivtv: ==================== END INIT IVTV ====================
Any input whould be appreciated,
thanks,tom
_______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
