I have a system with a Hauppauge PVR350 and PVR250 installed. I have been unable to get kradio (or other radio app like xmms-fmradio) to work.
$ ivtv-radio -f 91.5 works fine so I think I have the drives installed and loading ok. Is there some trick to getting this configured? Am I missing a piece here? Thanks R.Parr, RHCE, Temporal Arts $ dmesg | tac | > sed -n '/=\ \ END INIT IVTV\ \ =/,/= START INIT IVTV =/p; > /= START INIT IVTV =/q' | > tac ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.6.2 (tagged release) loading ivtv: Linux version: 2.6.16-2-amd64-k8 gcc-4.0 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. eth0: forcedeth.c: subsystem: 015d9:1011 bound to 0000:00:0a.0 ACPI: PCI Interrupt Link [LK2N] enabled at IRQ 45 GSI 21 sharing vector 0x42 and IRQ 21 ACPI: PCI Interrupt 0000:80:0a.0[A] -> Link [LK2N] -> GSI 45 (level, low) -> IRQ 66 PCI: Setting latency timer of device 0000:80:0a.0 to 64 ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 19 GSI 22 sharing vector 0x4A and IRQ 22 ACPI: PCI Interrupt 0000:05:02.2[B] -> Link [LNKA] -> GSI 19 (level, low) -> IRQ 74 ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[74] MMIO=[afbff800-afbfffff] Max Packet=[2048] IR/IT contexts=[4/8] i2c_adapter i2c-0: nForce2 SMBus adapter at 0x4c00 i2c_adapter i2c-1: nForce2 SMBus adapter at 0x4c40 gameport: EMU10K1 is pci0000:05:02.1/gameport0, io 0x9c00, speed 1206kHz ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based) ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 18 GSI 23 sharing vector 0x52 and IRQ 23 ACPI: PCI Interrupt 0000:06:08.0[A] -> Link [LNKC] -> GSI 18 (level, low) -> IRQ 82 tveeprom 2-0050: Hauppauge model 23552, rev D492, serial# 7894525 tveeprom 2-0050: tuner model is Philips FQ1236A MK4 (idx 92, type 57) tveeprom 2-0050: TV standards NTSC(M) (eeprom 0x08) tveeprom 2-0050: second tuner model is Philips TEA5768HL FM Radio (idx 101, type 62) tveeprom 2-0050: audio processor is CX25843 (idx 37) tveeprom 2-0050: decoder processor is CX25843 (idx 30) tveeprom 2-0050: has radio, has no IR remote ivtv0: This is the first unit of a PVR500 input: ImExPS/2 Generic Explorer Mouse as /class/input/input1 input: PC Speaker as /class/input/input2 tuner 2-0060: TEA5767 detected. tuner 2-0060: chip found @ 0xc0 (ivtv i2c driver #0) tuner 2-0060: type set to 62 (Philips TEA5767HN FM Radio) tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #0) ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 22 ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUS2] -> GSI 22 (level, low) -> IRQ 217 PCI: Setting latency timer of device 0000:00:02.1 to 64 ehci_hcd 0000:00:02.1: EHCI Host Controller ehci_hcd 0000:00:02.1: debug port 1 PCI: cache line size of 64 is not supported by device 0000:00:02.1 ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:02.1: irq 217, io mem 0xafce0000 ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 10 ports detected ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) pci_hotplug: PCI Hot Plug PCI Core version: 0.5 ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 21 ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUS0] -> GSI 21 (level, low) -> IRQ 225 PCI: Setting latency timer of device 0000:00:02.0 to 64 ohci_hcd 0000:00:02.0: OHCI Host Controller ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:02.0: irq 225, io mem 0xafcfc000 tda9887 2-0043: chip found @ 0x86 (ivtv i2c driver #0) usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 10 ports detected cx25840 2-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0) eth1: forcedeth.c: subsystem: 015d9:1011 bound to 0000:80:0a.0 usb 1-3: new high speed USB device using ehci_hcd and address 2 usb 1-3: configuration #1 chosen from 1 choice hub 1-3:1.0: USB hub found hub 1-3:1.0: 3 ports detected cx25840 2-0044: loaded v4l-cx25840.fw firmware (14264 bytes) wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #0) usb 1-3.1: new high speed USB device using ehci_hcd and address 3 usb 1-3.1: configuration #1 chosen from 1 choice hub 1-3.1:1.0: USB hub found hub 1-3.1:1.0: 3 ports detected ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023c0151113a32] eth1394: eth2: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0) usb 1-3.1.1: new high speed USB device using ehci_hcd and address 4 usb 1-3.1.1: configuration #1 chosen from 1 choice ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv0: Encoder revision: 0x02050032 ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) ivtv0: Create encoder radio stream tuner 2-0061: type set to 57 (Philips FQ1236A MK4) ivtv0: Initialized WinTV PVR 500 (unit #1), card #0 ivtv: ====================== NEXT CARD ====================== ivtv1: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based) ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 17 GSI 24 sharing vector 0x5A and IRQ 24 ACPI: PCI Interrupt 0000:06:09.0[A] -> Link [LNKD] -> GSI 17 (level, low) -> IRQ 90 tuner 3-0061: chip found @ 0xc2 (ivtv i2c driver #1) tda9887 3-0043: chip found @ 0x86 (ivtv i2c driver #1) wm8775 3-001b: chip found @ 0x36 (ivtv i2c driver #1) tveeprom 3-0050: Hauppauge model 23552, rev D492, serial# 7894525 tveeprom 3-0050: tuner model is Philips FQ1236A MK4 (idx 92, type 57) tveeprom 3-0050: TV standards NTSC(M) (eeprom 0x08) tveeprom 3-0050: second tuner model is Philips TEA5768HL FM Radio (idx 101, type 62) tveeprom 3-0050: audio processor is CX25843 (idx 37) tveeprom 3-0050: decoder processor is CX25843 (idx 30) tveeprom 3-0050: has radio, has no IR remote ivtv1: This is the second unit of a PVR500 ivtv1: Correcting tveeprom data: no radio present on second unit ivtv1: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv1: Encoder revision: 0x02050032 ivtv1: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv1: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total) ivtv1: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total) ivtv1: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) tuner 3-0061: type set to 57 (Philips FQ1236A MK4) ivtv1: i2c hardware 0x00000001 not found for command 0xc008561c! ivtv1: i2c addr 0x44 not found for command 0x40045613! ivtv1: i2c addr 0x44 not found for command 0xc0045627! ivtv1: i2c addr 0x44 not found for command 0x40345622! ivtv1: i2c addr 0x44 not found for command 0x40045612! ivtv1: i2c hardware 0x00000001 not found for command 0xc008561c! ivtv1: i2c hardware 0x00000001 not found for command 0xc008561c! ivtv1: i2c addr 0x44 not found for command 0x40045613! ivtv1: i2c addr 0x44 not found for command 0x40045612! ivtv1: i2c hardware 0x00000001 not found for command 0xc008561c! ivtv1: Initialized WinTV PVR 500 (unit #2), card #1 ivtv: ==================== END INIT IVTV ==================== _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
