Hello
Thanks for the short answer. Here is the dmesg output:
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.7.0 (development snapshot compiled on So 23 Jul 2006 11:08:56 CEST) loading
ivtv: Linux version: 2.6.16.13-4-smp SMP 586 REGPARM gcc-4.1
ivtv: In case of problems please include the debug info between
ivtv: the START INIT IVTV and END INIT IVTV lines, along with
ivtv: any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected Hauppauge WinTV PVR-350 card (cx23415 based)
ACPI: PCI Interrupt 0000:01:0a.0[A] -> GSI 22 (level, low) -> IRQ 66
tveeprom 1-0050: Hauppauge model 48139, rev K257, serial# 8379299
tveeprom 1-0050: tuner model is Philips FM1216 ME MK3 (idx 57, type 38)
tveeprom 1-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) (eeprom 0x74)
tveeprom 1-0050: audio processor is MSP4418 (idx 25)
tveeprom 1-0050: decoder processor is SAA7115 (idx 19)
tveeprom 1-0050: has radio, has IR remote
tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)
tda9887 1-0043: chip found @ 0x86 (ivtv i2c driver #0)
saa7115 1-0021: saa7115 found @ 0x42 (ivtv i2c driver #0)
saa7127 1-0044: saa7129 found @ 0x88 (ivtv i2c driver #0)
msp3400 1-0040: MSP4418G-B3 found @ 0x80 (ivtv i2c driver #0)
msp3400 1-0040: MSP4418G-B3 supports nicam and radio, mode is autodetect and autoselect
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes)
ivtv0: Encoder revision: 0x02050032
ivtv0: Decoder revision: 0x02020023
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
ivtv0: Create encoder radio stream
ivtv0: Allocate DMA decoder MPEG stream: 16 x 65536 buffers (1024KB total)
ivtv0: Allocate DMA decoder VBI stream: 512 x 2048 buffers (1024KB total)
ivtv0: Create decoder VOUT stream
ivtv0: Allocate DMA decoder YUV stream: 20 x 51840 buffers (1024KB total)
ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 bytes)
tuner 1-0061: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3))
tuner 1-0061: pal= argument not recognised
ivtv0: Initialized Hauppauge WinTV PVR-350, card #0
ivtv: ==================== END INIT IVTV ====================
When I try to view or stream the signal, I get these error messages:
ivtv0: All encoder MPEG stream buffers are full. Dropping data.
ivtv0: Cause: the application is not reading fast enough.
ivtv0: All encoder MPEG stream buffers are full. Dropping data.
ivtv0: Cause: the application is not reading fast enough.
ivtv0: All encoder MPEG stream buffers are full. Dropping data.
ivtv0: Cause: the application is not reading fast enough.
ivtv0: All encoder MPEG stream buffers are full. Dropping data.
ivtv0: Cause: the application is not reading fast enough.
ivtv0: All encoder MPEG stream buffers are full. Dropping data.
ivtv0: Cause: the application is not reading fast enough.
ivtv0: All encoder MPEG stream buffers are full. Dropping data.
ivtv0: Cause: the application is not reading fast enough.
ivtv0: All encoder MPEG stream buffers are full. Dropping data.
ivtv0: Cause: the application is not reading fast enough.
ivtv0 warning: ivtv ioctl: set bitrate=900000 < peak=510000: failed
ivtv0 warning: ivtv ioctl: set bitrate=1200000 < peak=910000: failed
ivtv0 warning: ivtv ioctl: set bitrate=5200000 < peak=1300000: failed
ivtv0 warning: ivtv ioctl: set bitrate=52000000 < peak=5300000: failed
The machine is a brand new (/proc/cpuinfo): Intel(R) Pentium(R) D CPU 3.00GHz with about 512 MB Ram. I use SuSE 10.1 (plain install without any updates). Unfortunately I have a bit a time problem. The Installation (PVR-350) is for media (streaming) event in september and should actually be tested.
Many thanks
Roland Kaeser
Thanks for the short answer. Here is the dmesg output:
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.7.0 (development snapshot compiled on So 23 Jul 2006 11:08:56 CEST) loading
ivtv: Linux version: 2.6.16.13-4-smp SMP 586 REGPARM gcc-4.1
ivtv: In case of problems please include the debug info between
ivtv: the START INIT IVTV and END INIT IVTV lines, along with
ivtv: any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected Hauppauge WinTV PVR-350 card (cx23415 based)
ACPI: PCI Interrupt 0000:01:0a.0[A] -> GSI 22 (level, low) -> IRQ 66
tveeprom 1-0050: Hauppauge model 48139, rev K257, serial# 8379299
tveeprom 1-0050: tuner model is Philips FM1216 ME MK3 (idx 57, type 38)
tveeprom 1-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) (eeprom 0x74)
tveeprom 1-0050: audio processor is MSP4418 (idx 25)
tveeprom 1-0050: decoder processor is SAA7115 (idx 19)
tveeprom 1-0050: has radio, has IR remote
tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)
tda9887 1-0043: chip found @ 0x86 (ivtv i2c driver #0)
saa7115 1-0021: saa7115 found @ 0x42 (ivtv i2c driver #0)
saa7127 1-0044: saa7129 found @ 0x88 (ivtv i2c driver #0)
msp3400 1-0040: MSP4418G-B3 found @ 0x80 (ivtv i2c driver #0)
msp3400 1-0040: MSP4418G-B3 supports nicam and radio, mode is autodetect and autoselect
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes)
ivtv0: Encoder revision: 0x02050032
ivtv0: Decoder revision: 0x02020023
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
ivtv0: Create encoder radio stream
ivtv0: Allocate DMA decoder MPEG stream: 16 x 65536 buffers (1024KB total)
ivtv0: Allocate DMA decoder VBI stream: 512 x 2048 buffers (1024KB total)
ivtv0: Create decoder VOUT stream
ivtv0: Allocate DMA decoder YUV stream: 20 x 51840 buffers (1024KB total)
ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 bytes)
tuner 1-0061: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3))
tuner 1-0061: pal= argument not recognised
ivtv0: Initialized Hauppauge WinTV PVR-350, card #0
ivtv: ==================== END INIT IVTV ====================
When I try to view or stream the signal, I get these error messages:
ivtv0: All encoder MPEG stream buffers are full. Dropping data.
ivtv0: Cause: the application is not reading fast enough.
ivtv0: All encoder MPEG stream buffers are full. Dropping data.
ivtv0: Cause: the application is not reading fast enough.
ivtv0: All encoder MPEG stream buffers are full. Dropping data.
ivtv0: Cause: the application is not reading fast enough.
ivtv0: All encoder MPEG stream buffers are full. Dropping data.
ivtv0: Cause: the application is not reading fast enough.
ivtv0: All encoder MPEG stream buffers are full. Dropping data.
ivtv0: Cause: the application is not reading fast enough.
ivtv0: All encoder MPEG stream buffers are full. Dropping data.
ivtv0: Cause: the application is not reading fast enough.
ivtv0: All encoder MPEG stream buffers are full. Dropping data.
ivtv0: Cause: the application is not reading fast enough.
ivtv0 warning: ivtv ioctl: set bitrate=900000 < peak=510000: failed
ivtv0 warning: ivtv ioctl: set bitrate=1200000 < peak=910000: failed
ivtv0 warning: ivtv ioctl: set bitrate=5200000 < peak=1300000: failed
ivtv0 warning: ivtv ioctl: set bitrate=52000000 < peak=5300000: failed
The machine is a brand new (/proc/cpuinfo): Intel(R) Pentium(R) D CPU 3.00GHz with about 512 MB Ram. I use SuSE 10.1 (plain install without any updates). Unfortunately I have a bit a time problem. The Installation (PVR-350) is for media (streaming) event in september and should actually be tested.
Many thanks
Roland Kaeser
----- Ursprüngliche Mail ----
Von: Hans Verkuil <[EMAIL PROTECTED]>
An: Roland Kaeser <[EMAIL PROTECTED]>
CC: User discussion about IVTV <[email protected]>
Gesendet: Donnerstag, den 3. August 2006, 08:40:30 Uhr
Betreff: Re: AW: [ivtv-users] Sound disapears after a few seconds
Von: Hans Verkuil <[EMAIL PROTECTED]>
An: Roland Kaeser <[EMAIL PROTECTED]>
CC: User discussion about IVTV <[email protected]>
Gesendet: Donnerstag, den 3. August 2006, 08:40:30 Uhr
Betreff: Re: AW: [ivtv-users] Sound disapears after a few seconds
On Thursday 03 August 2006 08:30, Roland Kaeser wrote:
> Hello
>
> You have absolutly right. Its a brand new PVR-350. And I'm using
> Kernel 2.6.16-13. But in my distro, the msp3400 module was shipped
> with the distro kernel and was not compiled with the ivtv-drivers.
> Have I made something wrong?
Please provide the INIT IVTV messages from the kernel log (dmesg).
Mito's problem is related to his specific msp3400 chip (the msp3435g).
If you have a brand new pvr350 then it is unlikely that your problem is
related since you almost certainly have another msp model.
Hans
>
> regards
>
> Roland
>
> ----- Ursprüngliche Mail ----
> Von: Mito Tranin - Lists <[EMAIL PROTECTED]>
> An: Roland Kaeser <[EMAIL PROTECTED]>; User discussion about IVTV
> <[email protected]> CC: Hans Verkuil <[EMAIL PROTECTED]>
> Gesendet: Donnerstag, den 3. August 2006, 04:19:53 Uhr
> Betreff: Re: [ivtv-users] Sound disapears after a few seconds
>
> Roland Kaeser wrote:
> > Hello
> >
> > I have a strange problem with the sound of the card. When I
> > initially configure the card with ivtvctl the sound remains like
> > muted altough mute is set to 0. When I then later switch the
> > audio inputs from 1 to 3 and back the sound comes for about 3
> > seconds and then goes back to muted. But the muted values remains
> > to 0. Can somebody give me a hint what could happend .
>
> I'm having this exact same problem, and Hans is helping me through
> it. It apears as though my version of the PVR-350 is incompatible
> with the current msp3400 module, and he is working through it to fix
> it up. Do you possibly have a PVR-350? or possibly a very old
> PVR-250? If so, you might be suffering from the same problem. If
> so, let Hans know, as he would probably love another test subject for
> this problem.
>
> Mito
> Hello
>
> You have absolutly right. Its a brand new PVR-350. And I'm using
> Kernel 2.6.16-13. But in my distro, the msp3400 module was shipped
> with the distro kernel and was not compiled with the ivtv-drivers.
> Have I made something wrong?
Please provide the INIT IVTV messages from the kernel log (dmesg).
Mito's problem is related to his specific msp3400 chip (the msp3435g).
If you have a brand new pvr350 then it is unlikely that your problem is
related since you almost certainly have another msp model.
Hans
>
> regards
>
> Roland
>
> ----- Ursprüngliche Mail ----
> Von: Mito Tranin - Lists <[EMAIL PROTECTED]>
> An: Roland Kaeser <[EMAIL PROTECTED]>; User discussion about IVTV
> <[email protected]> CC: Hans Verkuil <[EMAIL PROTECTED]>
> Gesendet: Donnerstag, den 3. August 2006, 04:19:53 Uhr
> Betreff: Re: [ivtv-users] Sound disapears after a few seconds
>
> Roland Kaeser wrote:
> > Hello
> >
> > I have a strange problem with the sound of the card. When I
> > initially configure the card with ivtvctl the sound remains like
> > muted altough mute is set to 0. When I then later switch the
> > audio inputs from 1 to 3 and back the sound comes for about 3
> > seconds and then goes back to muted. But the muted values remains
> > to 0. Can somebody give me a hint what could happend .
>
> I'm having this exact same problem, and Hans is helping me through
> it. It apears as though my version of the PVR-350 is incompatible
> with the current msp3400 module, and he is working through it to fix
> it up. Do you possibly have a PVR-350? or possibly a very old
> PVR-250? If so, you might be suffering from the same problem. If
> so, let Hans know, as he would probably love another test subject for
> this problem.
>
> Mito
_______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
