Hi, I have a PVR150 that worked just fine with some previous versions, but since upgrading to 0.6.x it won't budge anymore. Syslog notes:
Aug 21 08:59:04 vanquish kernel: ivtv: ==================== START INIT IVTV ==================== Aug 21 08:59:04 vanquish kernel: ivtv: version 0.6.3 (tagged release) loading Aug 21 08:59:04 vanquish kernel: ivtv: Linux version: 2.6.16.11 preempt K7 gcc-4.0 Aug 21 08:59:04 vanquish kernel: ivtv: In case of problems please include the debug info between Aug 21 08:59:04 vanquish kernel: ivtv: the START INIT IVTV and END INIT IVTV lines, along with Aug 21 08:59:04 vanquish kernel: ivtv: any module options, when mailing the ivtv-users mailinglist. Aug 21 08:59:04 vanquish kernel: ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based) Aug 21 08:59:04 vanquish kernel: ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 18 (level, low) -> IRQ 201 Aug 21 08:59:04 vanquish kernel: tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0) Aug 21 08:59:04 vanquish kernel: tda9887 0-0043: chip found @ 0x86 (ivtv i2c driver #0) Aug 21 08:59:04 vanquish kernel: tveeprom 0-0050: Hauppauge model 26559, rev C260, serial# 7627091 Aug 21 08:59:04 vanquish kernel: tveeprom 0-0050: tuner model is LG S001D MK3 (idx 60, type 38) Aug 21 08:59:04 vanquish kernel: tveeprom 0-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) (eeprom 0x74) Aug 21 08:59:04 vanquish kernel: tveeprom 0-0050: audio processor is CX25843 (idx 37) Aug 21 08:59:04 vanquish kernel: tveeprom 0-0050: decoder processor is CX25843 (idx 30) Aug 21 08:59:04 vanquish kernel: tveeprom 0-0050: has radio, has no IR remote Aug 21 08:59:04 vanquish kernel: ivtv0: Failed to load module cx25840 Aug 21 08:59:05 vanquish kernel: ivtv0: Failed to load module wm8775 Aug 21 08:59:05 vanquish kernel: ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) Aug 21 08:59:05 vanquish kernel: ivtv0: Encoder revision: 0x02050032 Aug 21 08:59:05 vanquish kernel: ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) Aug 21 08:59:05 vanquish kernel: ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total) Aug 21 08:59:05 vanquish kernel: ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total) Aug 21 08:59:05 vanquish kernel: ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) Aug 21 08:59:05 vanquish kernel: ivtv0: Create encoder radio stream Aug 21 08:59:05 vanquish kernel: tuner 0-0061: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3)) Aug 21 08:59:05 vanquish kernel: ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c! Aug 21 08:59:05 vanquish kernel: ivtv0: i2c addr 0x44 not found for command 0xc0045627! Aug 21 08:59:05 vanquish kernel: ivtv0: i2c hardware 0x00000020 not found for command 0x40345622! Aug 21 08:59:05 vanquish kernel: ivtv0: i2c addr 0x44 not found for command 0x40345622! Aug 21 08:59:05 vanquish kernel: ivtv0: i2c hardware 0x00000001 not found for command 0xc008561c! Aug 21 08:59:05 vanquish last message repeated 2 times Aug 21 08:59:05 vanquish kernel: ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 Aug 21 08:59:05 vanquish kernel: ivtv: ==================== END INIT IVTV ==================== and each time we try to access the driver (i.e. cat /dev/video0 > test.mpg) it shows errors like: Aug 21 09:00:50 vanquish kernel: ivtv0: i2c addr 0x44 not found for command 0xc0cc5605! Aug 21 09:00:50 vanquish kernel: ivtv0: i2c addr 0x44 not found for command 0x40045613! Aug 21 09:00:50 vanquish kernel: ivtv0: i2c addr 0x44 not found for command 0x40045612! (the resulting file is 0 bytes) I am running ivtv0.6.3 with the firmware downloaded from ivtvdriver.org. As someone on a forum suggested I also tried several PCI slots, but this had no result. Anyone have a suggestion for this ? Best regards, Florian _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
