Hans, here is the output you requested. I'll do a bit of poking around with ivtvctl myself. My memory must be failing because I had been certain it was a pvr-150, but there you go. Also, I notice that the video signal is listed as bad yet when I plug it into the television with the exact same cable path, the reception on the television is great.
Thanks very much for your help and suggestions. Daniel % ivtv-tune -c7 -d/dev/video -tus-cable /dev/video: 175.250 MHz % ivtvctl --log-status ioctl VIDIOC_LOG_STATUS ok ivtv0: ================= START STATUS CARD #0 ================= tveeprom 2-0050: Hauppauge model 48011, rev F310, serial# 5193118 tveeprom 2-0050: tuner model is Philips FI1236 MK2 (idx 10, type 2) tveeprom 2-0050: TV standards NTSC(M) (eeprom 0x08) tveeprom 2-0050: audio processor is MSP3435 (idx 10) tveeprom 2-0050: has radio tuner 2-0061: Tuner mode: analog TV tuner 2-0061: Frequency: 175.25 MHz tuner 2-0061: Standard: 0x0000b000 saa7115 2-0021: Audio frequency: 48000 Hz saa7115 2-0021: Input: Composite 4 saa7115 2-0021: Video signal: bad saa7115 2-0021: Frequency: 60 Hz saa7115 2-0021: Detected format: NTSC msp3400 2-0040: MSP3435G-B6 rev1 = 0x0207 rev2 = 0x2346 msp3400 2-0040: Audio: volume 58880 msp3400 2-0040: Audio: balance 32768 bass 32768 treble 32768 loudness off msp3400 2-0040: Standard: 4.5 M BTSC-Stereo (stereo) msp3400 2-0040: Audmode: 0x0001 msp3400 2-0040: Routing: 0x00000000 (input) 0x00000044 (output) msp3400 2-0040: ACB: 0x0c00 ivtv0: ================== END STATUS CARD #0 ================== -- On Fri, 2006-09-08 at 21:46 +0200, Hans Verkuil wrote: > On Friday 08 September 2006 20:05, Daniel Parish wrote: > > My pvr-150 is now recognized and I can capture video/audio from the > > s-video port, despite misidentification of the card as a pvr-250 and > > the firmware loading errors in the log file (see below). > > It's not misdetected. You DO have a PVR-250. The 150 has completely > differect supporting chips. There is no mistake possible. > > The firmware loading errors are actually a bug in the hotplug scripts > (if I remember correctly) and can be ignored. > > > The tuner > > appears to be recognized and set properly, but I can't tune with it; > > the channels aren't received properly, but I can see/hear enough to > > know that I am close. > > Can you give the output of ivtvctl --log-status? Perhaps that might give > me a clue. The tuner is programmed correctly (I checked against the > datasheet). > > Hans > > > > > I have verified that the cable is good by hooking it to a tv. I have > > tried the us-cable, us-cable-hrm, us-cable-irc and us-bcast frequency > > tables via ivtv-tune, but but still no luck. > > > > The system info: > > > > Fedora Core 5 > > Kernel 2.6.17-1, compiled from kernel org sources using a slightly > > modified FC5 config-2.6.17-1.2157_FC5 > > DFI Lanparty NFII Ultra B motherboard with an Athlon 2500+ processor > > Chipset nforce 2 > > > > Software -- All installed from source > > ivtv-0.7.0 > > Video-Frequencies-0.03 > > Video-ivtv-0.13 > > Config-IniFiles-2.39 > > Latest firmware files installed in /lib/firmware. > > > > Suggestions would be greatly appreciated. > > > > Thanks. > > > > Daniel > > > > > > > > kernel: ivtv: ==================== START INIT IVTV > > ==================== kernel: ivtv: version 0.7.0 (tagged release) > > loading > > kernel: ivtv: Linux version: 2.6.17.6-c1 mod_unload 686 REGPARM > > 4KSTACKS gcc-4.1 > > kernel: ivtv: In case of problems please include the debug info > > between kernel: ivtv: the START INIT IVTV and END INIT IVTV lines, > > along with kernel: ivtv: any module options, when mailing the > > ivtv-users mailinglist. > > kernel: ivtv0: Autodetected Hauppauge WinTV PVR-250 card (cx23415 > > based) kernel: ACPI: PCI Interrupt 0000:01:09.0[A] -> Link [APC2] -> > > GSI 17 (level, high) -> IRQ 19 > > kernel: tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #0) > > kernel: saa7115 2-0021: saa7115 found @ 0x42 (ivtv i2c driver #0) > > kernel: msp3400 2-0040: MSP3435G-B6 found @ 0x80 (ivtv i2c driver #0) > > kernel: msp3400 2-0040: MSP3435G-B6 supports radio, mode is > > autodetect and autoselect > > kernel: tveeprom 2-0050: Hauppauge model 48011, rev F310, serial# > > 5193118 > > kernel: tveeprom 2-0050: tuner model is Philips FI1236 MK2 (idx 10, > > type 2) > > kernel: tveeprom 2-0050: TV standards NTSC(M) (eeprom 0x08) > > kernel: tveeprom 2-0050: audio processor is MSP3435 (idx 10) > > kernel: tveeprom 2-0050: has radio > > kernel: ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) > > kernel: ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes) > > firmware_helper[3109]: Loading of /lib/firmware/v4l-cx2341x-enc.fw > > for ivtv driver failed: No such file or directory > > firmware_helper[3112]: Loading of /lib/firmware/v4l-cx2341x-dec.fw > > for ivtv driver failed: No such file or directory > > kernel: ivtv0: Encoder revision: 0x02050032 > > kernel: ivtv0: Decoder revision: 0x02020023 > > kernel: ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers > > (4096KB total) > > kernel: ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers > > (2048KB total) > > kernel: ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers > > (2048KB total) > > kernel: ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 > > buffers (2048KB total) > > kernel: ivtv0: Create encoder radio stream > > kernel: tuner 2-0061: type set to 2 (Philips NTSC (FI1236,FM1236 and > > compatibles)) > > kernel: ivtv0: Initialized Hauppauge WinTV PVR-250, card #0 > > kernel: ivtv: ==================== END INIT IVTV > > ==================== > > _______________________________________________ > ivtv-users mailing list > [email protected] > http://ivtvdriver.org/mailman/listinfo/ivtv-users -- Daniel Parish <[EMAIL PROTECTED]> _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
