Hello, when loading the driver with a PVR250, I get the message, that the eeprom might be corrupt:
Oct 30 17:26:02 epia2 kernel: ivtv: ==================== START INIT IVTV ==================== Oct 30 17:26:02 epia2 kernel: ivtv: version 0.8.0 (tagged release) loading Oct 30 17:26:02 epia2 kernel: ivtv: Linux version: 2.6.18-epia mod_unload VIAC3-2 gcc-4.1 Oct 30 17:26:02 epia2 kernel: ivtv: In case of problems please include the debug info between Oct 30 17:26:02 epia2 kernel: ivtv: the START INIT IVTV and END INIT IVTV lines, along with Oct 30 17:26:02 epia2 kernel: ivtv: any module options, when mailing the ivtv-users mailinglist. Oct 30 17:26:02 epia2 kernel: ivtv0: Autodetected Hauppauge WinTV PVR-250 card (cx23416 based) Oct 30 17:26:02 epia2 kernel: ivtv0 info: base addr: 0xdc000000 Oct 30 17:26:02 epia2 kernel: ivtv0 info: Enabling pci device Oct 30 17:26:02 epia2 kernel: ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10 Oct 30 17:26:02 epia2 kernel: ivtv0 info: Bus Mastering Enabled. Oct 30 17:26:02 epia2 kernel: ivtv0: Unreasonably low latency timer, setting to 64 (was 32) Oct 30 17:26:02 epia2 kernel: ivtv0 info: 22 (rev 1) at 00:14.0, irq: 10, latency: 64, memory: 0xdc000000 Oct 30 17:26:02 epia2 kernel: ivtv0 info: attempting ioremap at 0xdc000000 len 0x00800000 Oct 30 17:26:02 epia2 kernel: ivtv0 info: attempting ioremap at 0xdd000000 len 0x00800000 Oct 30 17:26:02 epia2 kernel: ivtv0 info: attempting ioremap at 0xde000000 len 0x00010000 Oct 30 17:26:02 epia2 kernel: ivtv0 info: Stopping VDM Oct 30 17:26:02 epia2 kernel: ivtv0 info: Stopping AO Oct 30 17:26:02 epia2 kernel: ivtv0 info: pinging (?) APU Oct 30 17:26:02 epia2 kernel: ivtv0 info: Stopping VPU Oct 30 17:26:02 epia2 kernel: ivtv0 info: Resetting Hw Blocks Oct 30 17:26:02 epia2 kernel: ivtv0 info: Stopping SPU Oct 30 17:26:02 epia2 kernel: ivtv0 info: Sleeping for 10ms Oct 30 17:26:02 epia2 kernel: ivtv0 info: init Encoder SDRAM pre-charge Oct 30 17:26:02 epia2 kernel: ivtv0 info: init Encoder SDRAM refresh to 1us Oct 30 17:26:02 epia2 kernel: ivtv0 info: init Decoder SDRAM pre-charge Oct 30 17:26:02 epia2 kernel: ivtv0 info: init Decoder SDRAM refresh to 1us Oct 30 17:26:02 epia2 kernel: ivtv0 info: Sleeping for 600ms (600 recommended) Oct 30 17:26:02 epia2 kernel: ivtv0 info: Card ready for firmware! Oct 30 17:26:02 epia2 kernel: ivtv0 info: Loading encoder image Oct 30 17:26:02 epia2 kernel: ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) Oct 30 17:26:02 epia2 kernel: ivtv0 info: Sleeping for 100 ms Oct 30 17:26:03 epia2 kernel: ivtv0 info: Sleeping for 100 ms Oct 30 17:26:03 epia2 kernel: ivtv0 info: activating i2c... Oct 30 17:26:03 epia2 kernel: ivtv0 info: Active card count: 1. Oct 30 17:26:03 epia2 kernel: ivtv0 info: Loaded module tveeprom Oct 30 17:26:03 epia2 kernel: tveeprom 1-0050: Encountered bad packet header [ff]. Corrupt or not a Hauppauge eeprom. Oct 30 17:26:03 epia2 kernel: ivtv0 info: Loaded module tuner Oct 30 17:26:03 epia2 kernel: saa7115 1-0021: saa71115 found @ 0x42 (ivtv i2c driver #0) Oct 30 17:26:03 epia2 kernel: ivtv0 info: Loaded module saa7115 Oct 30 17:26:03 epia2 kernel: msp3400 1-0040: MSP18415O-C31 found @ 0x80 (ivtv i2c driver #0) Oct 30 17:26:03 epia2 kernel: msp3400 1-0040: MSP18415O-C31 supports nicam and radio, mode is autodetect and autoselect Oct 30 17:26:03 epia2 kernel: ivtv0 info: Loaded module msp3400 Oct 30 17:26:03 epia2 kernel: ivtv0 info: About to search for mailboxes Oct 30 17:26:03 epia2 kernel: ivtv0 info: Searching for encoder mailbox Oct 30 17:26:03 epia2 kernel: ivtv0 info: match: 0x34567812 at 0xced80104. match: 1 Oct 30 17:26:03 epia2 kernel: ivtv0 info: match: 0x56781234 at 0xced80108. match: 2 Oct 30 17:26:03 epia2 kernel: ivtv0 info: match: 0x78123456 at 0xced8010c. match: 3 Oct 30 17:26:03 epia2 kernel: ivtv0 info: found encoder mailbox! Oct 30 17:26:03 epia2 kernel: ivtv0 info: Encoder OK Oct 30 17:26:03 epia2 kernel: ivtv0 info: Getting firmware version.. Oct 30 17:26:03 epia2 kernel: ivtv0 info: Getting encoder firmware rev. Oct 30 17:26:03 epia2 kernel: ivtv0: Encoder revision: 0x02050032 Oct 30 17:26:03 epia2 kernel: ivtv0 info: v4l2 streams setup Oct 30 17:26:03 epia2 kernel: ivtv0 info: Configuring Hauppauge WinTV PVR-250 card with 4 streams Oct 30 17:26:03 epia2 kernel: ivtv0: Registered device video1 for encoder MPEG Oct 30 17:26:03 epia2 kernel: ivtv0 info: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) Oct 30 17:26:03 epia2 kernel: ivtv0: Registered device video33 for encoder YUV Oct 30 17:26:03 epia2 kernel: ivtv0 info: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total) Oct 30 17:26:03 epia2 kernel: ivtv0: Registered device vbi1 for encoder VBI Oct 30 17:26:03 epia2 kernel: ivtv0 info: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total) Oct 30 17:26:03 epia2 kernel: ivtv0: Registered device video25 for encoder PCM audio Oct 30 17:26:03 epia2 kernel: ivtv0 info: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) Oct 30 17:26:03 epia2 kernel: ivtv0 info: Starting Threads Oct 30 17:26:03 epia2 kernel: ivtv0 info: Changing input from 1 to 0 Oct 30 17:26:03 epia2 kernel: ivtv0 info: Mute Oct 30 17:26:03 epia2 kernel: ivtv0 info: ivtv_enc_thread: pid = 3453, itv = 0xc1d20000 Oct 30 17:26:03 epia2 kernel: ivtv0 info: encoder thread sleeping 3453 Oct 30 17:26:03 epia2 kernel: ivtv0 info: ivtv_enc_vbi_thread: pid = 3454, itv = 0xc1d20000 Oct 30 17:26:03 epia2 kernel: ivtv0 info: encoder thread sleeping 3454 Oct 30 17:26:03 epia2 kernel: ivtv0 info: Unmute Oct 30 17:26:03 epia2 kernel: ivtv0 info: Switching standard to 7. Oct 30 17:26:03 epia2 kernel: ivtv0 info: Mute Oct 30 17:26:03 epia2 kernel: ivtv0 info: v4l2 ioctl: set frequency 6400 Oct 30 17:26:03 epia2 kernel: ivtv0 info: Unmute Oct 30 17:26:03 epia2 kernel: ivtv0: Initialized Hauppauge WinTV PVR-250, card #0 Oct 30 17:26:03 epia2 kernel: ivtv: ==================== END INIT IVTV ==================== Is there any way to repair the eeprom contents? I have also some Problems with the tuner, I receive only noise, but the HW must be ok, it works with aformer version. Thanks for help! Dirk _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
