Hello, I found the problem, my card seems to require the parameter newi2c=0 to be set, then I get this output and everything is fine:
Nov 1 20:44:17 epia2 kernel: ivtv: ==================== START INIT IVTV ==================== Nov 1 20:44:17 epia2 kernel: ivtv: version 0.8.0 (tagged release) loading Nov 1 20:44:17 epia2 kernel: ivtv: Linux version: 2.6.18-epia mod_unload VIAC3-2 gcc-4.1 Nov 1 20:44:17 epia2 kernel: ivtv: In case of problems please include the debug info between Nov 1 20:44:17 epia2 kernel: ivtv: the START INIT IVTV and END INIT IVTV lines, along with Nov 1 20:44:17 epia2 kernel: ivtv: any module options, when mailing the ivtv-users mailinglist. Nov 1 20:44:17 epia2 kernel: ivtv0: Autodetected Hauppauge WinTV PVR-250 card (cx23416 based) Nov 1 20:44:17 epia2 kernel: ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10 Nov 1 20:44:17 epia2 kernel: ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) Nov 1 20:44:18 epia2 kernel: i2c-algo-bit.o: (0) scl=1, sda=1 Nov 1 20:44:18 epia2 kernel: i2c-algo-bit.o: (1) scl=1, sda=0 Nov 1 20:44:18 epia2 kernel: i2c-algo-bit.o: (2) scl=1, sda=1 Nov 1 20:44:18 epia2 kernel: i2c-algo-bit.o: (3) scl=0, sda=1 Nov 1 20:44:18 epia2 kernel: i2c-algo-bit.o: (4) scl=1, sda=1 Nov 1 20:44:18 epia2 kernel: i2c-algo-bit.o: ivtv i2c driver #0 passed test. Nov 1 20:44:18 epia2 kernel: tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) Nov 1 20:44:18 epia2 kernel: saa7115 1-0021: saa7115 found @ 0x42 (ivtv i2c driver #0) Nov 1 20:44:18 epia2 kernel: msp3400 1-0040: MSP3415G-B8 found @ 0x80 (ivtv i2c driver #0) Nov 1 20:44:18 epia2 kernel: msp3400 1-0040: MSP3415G-B8 supports nicam and radio, mode is autodetect and autosele ct Nov 1 20:44:18 epia2 kernel: tveeprom 1-0050: Hauppauge model 32034, rev B248, serial# 6476004 Nov 1 20:44:18 epia2 kernel: tveeprom 1-0050: tuner model is LG TP18PSB11D (idx 48, type 29) Nov 1 20:44:18 epia2 kernel: tveeprom 1-0050: TV standards PAL(B/G) (eeprom 0x04) Nov 1 20:44:18 epia2 kernel: tveeprom 1-0050: audio processor is MSP3415 (idx 6) Nov 1 20:44:18 epia2 kernel: tveeprom 1-0050: decoder processor is SAA7115 (idx 19) Nov 1 20:44:18 epia2 kernel: tveeprom 1-0050: has no radio, has IR remote Nov 1 20:44:18 epia2 kernel: ivtv0: Encoder revision: 0x02050032 Nov 1 20:44:18 epia2 kernel: ivtv0: Registered device video1 for encoder MPEG Nov 1 20:44:18 epia2 kernel: ivtv0: Registered device video33 for encoder YUV Nov 1 20:44:18 epia2 kernel: ivtv0: Registered device vbi1 for encoder VBI Nov 1 20:44:18 epia2 kernel: ivtv0: Registered device video25 for encoder PCM audio Nov 1 20:44:18 epia2 kernel: tuner 1-0061: type set to 29 (LG PAL_BG (TPI8PSB11D)) Nov 1 20:44:19 epia2 kernel: ivtv0: Initialized Hauppauge WinTV PVR-250, card #0 Nov 1 20:44:19 epia2 kernel: ivtv: ==================== END INIT IVTV ==================== The tuner works! The question is onyl why is my cord not compatible with the new i2c implementation? Am Sonntag, 29. Oktober 2006 21:56 schrieb Dirk Aust: > Hello, > I have some problems with with the tuner on a PVR250, everything works > properly, but with the tuner as source I get only snow, what is the right > value for the PAL parameter in Germany? > > Thanks! > > _______________________________________________ > ivtv-users mailing list > [email protected] > http://ivtvdriver.org/mailman/listinfo/ivtv-users _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
