Hello,
I have Hauppauge WinTV PVR-150. I compiled latest driver, new kernel
(2.6.19.1) and I followed Debian Howto from wiki (mostly):
http://ivtvdriver.org/index.php/Howto:Debian
This is dmesg output of card initialization:
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.9.1 (tagged release) loading
ivtv: Linux version: 2.6.19.1jb3 SMP preempt mod_unload PENTIUMIII REGPARM
ivtv: In case of problems please include the debug info between
ivtv: the START INIT IVTV and END INIT IVTV lines, along with
ivtv: any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected Hauppauge card (cx23416 based)
ACPI: PCI Interrupt 0000:05:09.0[A] -> GSI 21 (level, low) -> IRQ 20
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0)
ivtv0: Failed to load module tveeprom
tveeprom 0-0050: Hauppauge model 26559, rev F089, serial# 9360137
tveeprom 0-0050: tuner model is TCL MFPE05 2 (idx 89, type 38)
tveeprom 0-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K)
(eeprom 0x74)
tveeprom 0-0050: audio processor is CX25843 (idx 37)
tveeprom 0-0050: decoder processor is CX25843 (idx 30)
tveeprom 0-0050: has radio, has no IR remote
ivtv0: Autodetected Hauppauge WinTV PVR-150
ivtv0: Failed to load module tuner
ivtv0: Failed to load module cx25840
ivtv0: Failed to load module wm8775
ivtv0: Encoder revision: 0x02050032
ivtv0: Registered device video0 for encoder MPEG
ivtv0: Registered device video32 for encoder YUV
ivtv0: Registered device vbi0 for encoder VBI
ivtv0: Registered device video24 for encoder PCM audio
ivtv0: Registered device radio0 for encoder radio
ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c!
ivtv0: i2c addr 0x44 not found for command 0x4008646f!
ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0x4008646d!
ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c!
ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c!
ivtv0: i2c hardware 0x00000001 (cx2584x) not found for command 0xc008561c!
ivtv0: Initialized Hauppauge WinTV PVR-150, card #0
ivtv: ==================== END INIT IVTV ====================
I have source and standard set up:
[EMAIL PROTECTED]:~$ v4l2-ctl -I
Video input : 0 (Tuner 1)
[EMAIL PROTECTED]:~$ v4l2-ctl -S
Video standard = 0x000000ff
PAL-B/B1/G/H/I/D/D1/K
When I do cat /dev/video0 | xine stdin://mpeg2, I see only noise (seems tuner
is tuned to dead channel). When I try tuning using ivtv-tune (or ptune-ui), I
still see dead channel. No matter how I tried changing the settings
(pal-europe,
pal-europe-east, ...), I see dead channel.
The input has signal (I got it from TV, my cable TV is working okay). Seems,
that tuning does not work well. Is there some software to
automatically discover
channels or settings? I'm in Slovak Republic, using UPC as cable provider.
Any ideas?
Thank you,
Juraj Bednar.
_______________________________________________
ivtv-users mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-users
