>> How can I find out if my PVR-150 is IR blasting-capable? Is is
>> possible to find out from software, or must one examine the hardware
>> itself?
>
> You get a special ir-receiver + ir-transmitter with the card. Also you
> can find the below in INIT IVTV.
> ivtv0: reopen i2c bus for IR-blaster support
>
> I am not sure if ivtv detects when it is not connected.
Here's my IVTV boot trace:
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.9.1 (tagged release) loading
ivtv: Linux version: 2.6.19.1-V2 mod_unload PENTIUM4 REGPARM
ivtv: In case of problems please include the debug info between
ivtv: the START INIT IVTV and END INIT IVTV lines, along with
ivtv: any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected Hauppauge card (cx23416 based)
ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 9
ACPI: PCI Interrupt 0000:01:01.0[A] -> Link [LNKG] -> GSI 9 (level,
low) -> IRQ 9
ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
input: MOSART Semi. Wireless Keyboard & Mouse as /class/input/input1
input: USB HID v1.10 Keyboard [MOSART Semi. Wireless Keyboard & Mouse]
on usb-0000:00:1d.0-1
input: MOSART Semi. Wireless Keyboard & Mouse as /class/input/input2
input: USB HID v1.10 Mouse [MOSART Semi. Wireless Keyboard & Mouse] on
usb-0000:00:1d.0-1
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
tveeprom 1-0050: Hauppauge model 26552, rev F068, serial# 10115408
tveeprom 1-0050: tuner model is LG TAPE H001F MK3 (idx 68, type 47)
tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 1-0050: audio processor is CX25843 (idx 37)
tveeprom 1-0050: decoder processor is CX25843 (idx 30)
tveeprom 1-0050: has radio, has no IR remote
ivtv0: Autodetected Hauppauge WinTV PVR-150
tuner 1-0043: chip found @ 0x86 (ivtv i2c driver #0)
tda9887 1-0043: tda988[5/6/7] found @ 0x43 (tuner)
tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)
cx25840 1-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
cx25840 1-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0)
ivtv0: Encoder revision: 0x02050032
ivtv0: Registered device video0 for encoder MPEG
ivtv0: Registered device video32 for encoder YUV
ivtv0: Registered device vbi0 for encoder VBI
ivtv0: Registered device video24 for encoder PCM audio
ivtv0: Registered device radio0 for encoder radio
tuner 1-0061: type set to 47 (LG NTSC (TAPE series))
ivtv0: Initialized Hauppauge WinTV PVR-150, card #0
ivtv: ==================== END INIT IVTV ====================
Based on this, it would seem that it has no IR blasting capabilities.
_______________________________________________
ivtv-users mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-users
