Hi, After switching to version 0.10.0, I can now get the test pattern when doing a modprobe saa7127 test_image=1.
After loading the ivtv module, dmesg says: ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.10.0 (tagged release) loading ivtv: Linux version: 2.6.19-1.2911.fc6 mod_unload ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected Hauppauge card (cx23415 based) PCI: Enabling device 0000:01:03.0 (0014 -> 0016) ivtv0: Unreasonably low latency timer, setting to 64 (was 16) pcilynx0: resetting bus (short bus reset) on request pcilynx0: bus reset interrupt pcilynx0: SelfID process finished (phyid 0, root) pcilynx0: SelfID packet 0x807f8c56 rcvd ieee1394: Host added: ID:BUS[0-00:1023] GUID[0800070200000000] scsi0 : MESH ivtv0: loaded v4l-cx2341x-enc.fw firmware (376836 bytes) ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes) ivtv0: Encoder revision: 0x02060039 ivtv0: Decoder revision: 0x02020023 tveeprom 0-0050: Hauppauge model 48132, rev K268, serial# 9904748 tveeprom 0-0050: tuner model is LG TAPE H001F MK3 (idx 68, type 47) tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08) tveeprom 0-0050: audio processor is MSP4448 (idx 27) tveeprom 0-0050: decoder processor is SAA7115 (idx 19) tveeprom 0-0050: has radio, has IR remote ivtv0: Autodetected Hauppauge WinTV PVR-350 tuner 0-0043: chip found @ 0x86 (ivtv i2c driver #0) tda9887 0-0043: tda988[5/6/7] found @ 0x43 (tuner) tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0) eth0: BMAC+ at 00:05:02:0f:b8:c2 saa7115 0-0021: saa7115 found (1f7115d0e100000) @ 0x42 (ivtv i2c driver #0) saa7127 0-0044: saa7129 found @ 0x88 (ivtv i2c driver #0) msp3400 0-0040: MSP4448G-A2 found @ 0x80 (ivtv i2c driver #0) msp3400 0-0040: MSP4448G-A2 supports radio, mode is autodetect and autoselect ivtv0: Registered device video0 for encoder MPEG (4 MB) ivtv0: Registered device video32 for encoder YUV (2 MB) ivtv0: Registered device vbi0 for encoder VBI (1 MB) ivtv0: Registered device video24 for encoder PCM audio (1 MB) ivtv0: Registered device radio0 for encoder radio ivtv0: Registered device video16 for decoder MPEG (1 MB) ivtv0: Registered device vbi8 for decoder VBI (1 MB) ivtv0: Registered device vbi16 for decoder VOUT ivtv0: Registered device video48 for decoder YUV (1 MB) ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 bytes) tuner 0-0061: type set to 47 (LG NTSC (TAPE series)) ivtv0: Initialized Hauppauge WinTV PVR-350, card #0 ivtv: ==================== END INIT IVTV ==================== after loading the ivtv-fb module, I get in dmesg: ivtv0-fb: Framebuffer at 0x85510000, mapped to 0xd7090000, size 1665k ivtv0-fb: === Validated display mode === ivtv0-fb: Display size 720x480 (720x480 Virtual) @ 32bpp ivtv0-fb: Display position 1,1 ivtv0-fb: Display filter : on ivtv0-fb: Color space : RGB ivtv0-fb: === Display mode change === ivtv0-fb: Display size 720x480 (720x480 Virtual) @ 32bpp ivtv0-fb: Display position 1,1 ivtv0-fb: Display filter : on ivtv0-fb: Color space : RGB ivtv0-fb: Running in compatibility mode. Display resize & mode change disabled ivtv0-fb: Framebuffer registered on ivtv card id 0 I still get a hang when I try [EMAIL PROTECTED] henry]# ivtvfbctl /dev/fb1 --globalalpha=off --localalpha=on It just hangs, but comes back after <CNTL>-C I also can't dd from /dev/video0 to /dev/video16 (blank screen) Is there anyone using ivtv on a PPC machine out there? (BTW, the xdriver won't load , but that's another problem) Thanks, Henry _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
