Yes. I applied the patch and it was successful. Then did a kernel re-compile and reboot.
Maarten Maathuis wrote: > Do you have the patch for the bug in kernel 2.6.20 applied? (the one > in the misc directory of the source iirc) It's for the cx25840. > > Maarten. > > On 3/6/07, David Liana <[EMAIL PROTECTED]> wrote: >> I have a problem with my WinTV-PVR-150 MCE. Using ivtv-0.10.1 and >> 2.6.20-gentoo, with the latest firmware. This is can be reproduced with >> many kernel/driver versions (tried with several versions of Ubuntu and >> Knoppmyth). Card works under Windows. >> >> I can run the "cat /dev/video0 > /tmp/test.mpg" and get video (but no >> sound). >> >> I try to use kdetv and I just get colored snow. However, it detects the >> channels I have. I get several of these messages when I use kdetv in >> /var/log/syslog: >> Mar 5 19:34:56 mccoy kernel: [81311.071338] ivtv0 warning: Cannot >> obtain 1690835328 bytes for encoder VBI data transfer >> >> MythTV also refuses to play and record TV. >> >> Here is my lspci -vvv output: >> 02:00.0 Multimedia video controller: Internext Compression Inc iTVC16 >> (CX23416) MPEG-2 Encoder (rev 01) >> Subsystem: Hauppauge computer works Inc. Unknown device b7f1 >> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- >> ParErr- Stepping- SERR+ FastB2B- >> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- >> <TAbort- <MAbort- >SERR- <PERR- >> Latency: 64 (32000ns min, 2000ns max), Cache Line Size: 64 bytes >> Interrupt: pin A routed to IRQ 21 >> Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M] >> Capabilities: [44] Power Management version 2 >> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA >> PME(D0-,D1-,D2-,D3hot-,D3cold-) >> Status: D0 PME-Enable- DSel=0 DScale=0 PME- >> >> >> Here is ivtv output: >> [ 6257.953201] ivtv: ==================== START INIT IVTV >> ==================== >> [ 6257.953210] ivtv: version 0.10.1 (tagged release) loading >> [ 6257.953214] ivtv: Linux version: 2.6.20-gentoo SMP mod_unload >> PENTIUM4 >> [ 6257.953218] ivtv: In case of problems please include the debug info >> between >> [ 6257.953221] ivtv: the START INIT IVTV and END INIT IVTV lines, along >> with >> [ 6257.953225] ivtv: any module options, when mailing the ivtv-users >> mailinglist. >> [ 6257.953312] ivtv0: Autodetected Hauppauge card (cx23416 based) >> [ 6258.014267] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 21 (level, >> low) -> IRQ 21 >> [ 6258.628479] PM: Adding info for No Bus:0000:02:00.0 >> [ 6258.651683] PM: Removing info for No Bus:0000:02:00.0 >> [ 6258.656914] ivtv0: loaded v4l-cx2341x-enc.fw firmware (376836 bytes) >> [ 6258.868091] ivtv0: Encoder revision: 0x02060039 >> [ 6258.868123] PM: Adding info for No Bus:i2c-0 >> [ 6258.871701] PM: Adding info for i2c:0-0050 >> [ 6258.877743] tuner 0-0043: chip found @ 0x86 (ivtv i2c driver #0) >> [ 6258.877768] PM: Adding info for i2c:0-0043 >> [ 6258.877810] tda9887 0-0043: tda988[5/6/7] found @ 0x43 (tuner) >> [ 6258.882420] tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0) >> [ 6258.882442] PM: Adding info for i2c:0-0061 >> [ 6258.905586] cx25840 0-0044: cx25843-23 found @ 0x88 (ivtv i2c >> driver #0) >> [ 6258.905619] PM: Adding info for i2c:0-0044 >> [ 6258.930059] PM: Adding info for No Bus:0-0044 >> [ 6258.940218] PM: Removing info for No Bus:0-0044 >> [ 6263.951729] cx25840 0-0044: loaded v4l-cx25840.fw firmware (16382 >> bytes) >> [ 6264.061566] wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0) >> [ 6264.073385] PM: Adding info for i2c:0-001b >> [ 6264.149919] tveeprom 0-0050: Hauppauge model 26552, rev F0A3, serial# >> 10217684 >> [ 6264.149927] tveeprom 0-0050: tuner model is TCL MFNM05-4 (idx 103, >> type 43) >> [ 6264.149935] tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08) >> [ 6264.149940] tveeprom 0-0050: audio processor is CX25843 (idx 37) >> [ 6264.149946] tveeprom 0-0050: decoder processor is CX25843 (idx 30) >> [ 6264.149952] tveeprom 0-0050: has radio, has no IR receiver, has no IR >> transmitter >> [ 6264.149959] ivtv0: Autodetected Hauppauge WinTV PVR-150 >> [ 6264.237934] ivtv0: Registered device video0 for encoder MPEG (4 MB) >> [ 6264.238178] ivtv0: Registered device video32 for encoder YUV (2 MB) >> [ 6264.238481] ivtv0: Registered device vbi0 for encoder VBI (1 MB) >> [ 6264.238588] ivtv0: Registered device video24 for encoder PCM audio >> (1 MB) >> [ 6264.238913] ivtv0: Registered device radio0 for encoder radio >> [ 6264.238938] tuner 0-0061: type set to 43 (Philips NTSC MK3 (FM1236MK3 >> or FM1236/F)) >> [ 6264.641092] ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 >> [ 6264.641145] ivtv: ==================== END INIT IVTV >> ==================== >> >> >> What am I missing here? >> >> Let me know if I need to provide anything else. >> >> Thanks, >> >> Dave >> >> _______________________________________________ >> ivtv-users mailing list >> [email protected] >> http://ivtvdriver.org/mailman/listinfo/ivtv-users >> > > _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
